Manual do usuário JL Audio Stealthbox SB-P-CYNNE/10W6v2/BK

Resumo do conteúdo contido na página número 1

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1
INSTALLATION
DIFFICULT Y:
If you choose to perform the installation yourself, it is absolutely vital that
®
OUT
the Stealthbox be properly mounted to the vehicle according to these
OF
instructions. Failure to mount the enclosure properly presents two problems:
INSTALL ATION GUIDE
for the 1) The sub-bass performance will suffer due to the movement of the enclosure
35
caused by the f

Resumo do conteúdo contido na página número 2

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 4 STEP 8 Remove the bottom sill plate. Remove the upper d-pillar trim. STEP 5 STEP 9 Remove the lower d-pillar trim. With a T-30 socket, remove the bolt and metal bracket that is located between the two rear seats. STEP 6 STEP 10 Remove the top sill plate. Grab a hold of the back of the driver’s side rear seat as in the picture. Lift the right side of the seat up and out of the hi

Resumo do conteúdo contido na página número 3

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 1 2 STEP 16 Remove the plastic collar that is around the hinge pin. Pull the SRS plastic badge from the upper c-pillar trim. With a T-25 socket, remove the bolt that has been exposed. STEP 1 3 STEP 17 Remove the trim panel. An airbag is located behind the c-pillar trim. Use caution while removing this panel. All wiring/connections should be protected. As in the illustration, r

Resumo do conteúdo contido na página número 4

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 24 STEP 2 0 Found in the rearmost driver’s side floor corner, remove With a T-25 socket, remove three bolts that secures this the rubber grommet in the cargo area. rear side trim panel. Unsecure the wire harness from the wheel well. *Make sure the ignition is not turned on* Loosen the bolt that secures the brown wires to the flooring of the vehicle. Once loose, turn this wire a

Resumo do conteúdo contido na página número 5

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 2 8 STEP 32 Fully thread the supplied coupler to the first socket cup set With a 9/16-inch socket and the remaining supplied pair of screw from STEP 27. bolt assemblies, secure the L-bracket to the Stealthbox®. Thread the second supplied socket cup set screw into the coupler. STEP 2 9 STEP 33 Place the Stealthbox® into position by guiding the socket From under the vehicle, place

Resumo do conteúdo contido na página número 6

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 3 6 STEP 40 With a T-25 socket, secure the rear of the side trim panel With a T-25 socket, secure the top c-pillar trim to the to the d-pillar, from STEP 20. c-pillar, from STEPS 16 & 17. STEP 3 7 STEP 41 With a T-25 socket, secure the front of the side trim panel Secure the upper d-pillar trim to the d-pillar, secure the trim to the c-pillar, from STEP 18. with the mounting scre

Resumo do conteúdo contido na página número 7

S SB B- -P P- -C CY YN NNE NE/ /1 10W 0W6 6v v2 2/ /B BK K_ _IIN NS ST TR R_ _S SKU KU# #0 01 11 123 231 1 STEP 4 4 INC L UDED H A RD W A RE Replace the cargo door sill plate, from STEP 4. (2) (2) 3 3/ /8 8- -in inch - ch -1 16 x 2 1 6 x 2 1/ /4 4- -iin nch S ch So ocket C cket Cu up S p Se et S t Sc crew rews s (7) (7) 3/8 3/8- -iin nc ch h Fl Fla at t Wa Was sh he er r ( (1 1) ) 3 3/ /8 8- -in inch - ch -1 16 S 6 So ocket C cket Cu up S p Se et S t Sc crew C rew Co oup uplle er r (5) (5