Resumo do conteúdo contido na página número 1
Operator’s manual (EPA)
232R 235R
Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
E E E En n n ng g g glllliiiis s s sh h h h
Resumo do conteúdo contido na página número 2
15 m 50FT KEY TO SYMBOLS Symbols Switch off the engine by moving the stop switch to the STOP position before carrying out any checks or maintenance. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or Always wear approved protective gloves. fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand Regular cleaning is requ
Resumo do conteúdo contido na página número 3
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS • Please read the operator’s manual carefully. Symbols ....................................................................... 2 Maintenance, replacement, or repair of the emission control CONTENTS devices and system may be performed by any nonroad Contents ...................................................................... 3 engine repair establishment or indi
Resumo do conteúdo contido na página número 4
INTRODUCTION Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lo
Resumo do conteúdo contido na página número 5
WHAT IS WHAT? 28 27 What is what? 1 Blade 15 Air purge 2 Grease filler cap, bevel gear 16 Air filter cover 3 Bevel gear 17 Handle adjustment 4 Cutting attachment guard 18 Locking nut 5 Shaft 19 Support flange 6 Handlebar 20 Support cup 7 Throttle control 21 Drive disc 8 Stop switch 22 Trimmer head 9 Throttle lock 23 Socket spanner 10 Support eyes for harness 24 Operator’s manual (EPA) 11 Cylinder cover 25 Transport guard 12 Starter handle 26 Allen key 13 Fuel tank 27 Locking pin 14 Choke
Resumo do conteúdo contido na página número 6
GENERAL SAFETY PRECAUTIONS HELMET Important A helmet should be worn if the trees being cleared are taller than 2 m. IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit HEARING PROTECTION are the cutting attachments we recommend in the chapter on Technical data. Wear hearing protection that provides adequate noise reduction. Never use the machine if you are tired, if y
Resumo do conteúdo contido na página número 7
GENERAL SAFETY PRECAUTIONS Press the throttle lock and make sure it returns to its original ′ ′ Machine′′s safety equipment position when you release it. This section describes the machine ′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. See the ”What is what?” section to locate where this equipment is positioned on your machine. The life span of the machine can be reduced and the risk of
Resumo do conteúdo contido na página número 8
GENERAL SAFETY PRECAUTIONS Regularly check the vibration damping units for cracks or Cutting attachment guard deformation. Check that the vibration damping element is undamaged and securely attached. WARNING! Overexposure to vibration can This guard is intended to prevent loose objects from being lead to circulatory damage or nerve damage thrown towards the operator. The guard also protects the ! in people who have impaired circulation. operator from accidental contact with t
Resumo do conteúdo contido na página número 9
GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut. Regularly check that the muffler is securely attached to the machine. The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put
Resumo do conteúdo contido na página número 10
GENERAL SAFETY PRECAUTIONS Cutting equipment Sharpening grass cutters and grass blades Saw blades are intended for cutting fibrous types of wood. • See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters Grass blades and grass cutters are intended for cutting using a single-cut flat file. coarse grass. • Sharpen all edges equally to maintain the balance of the blade. A trimmer head is intended for trimming grass. WARNING! Always discard a blade that
Resumo do conteúdo contido na página número 11
GENERAL SAFETY PRECAUTIONS so, this should be done before filing with a round file. The top edges must be filed down by the same amount for all the teeth. Adjust the blade setting. This should be 1 mm. Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. Thi
Resumo do conteúdo contido na página número 12
ASSEMBLY Fitting the handlebar (232R) Fitting the handlebar (235R) • Remove the screw at the rear of the throttle handle. • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the • Slide the throttle handle onto the right side of the handlebar, (see diagram). handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in • Align the screw hole in the throttle handle with the hole in the handlebar. the handlebar. •Re
Resumo do conteúdo contido na página número 13
ASSEMBLY Transport position, handlebar Fitting a blade guard, grass blade and grass cutter (232R) G F E D • The handlebar can easily be turned to fit along the shaft for easier transportation and storage. A B • Loosen the knob. Turn the handlebar clockwise so that the C throttle handle rests against the engine. • Now twist the handlebar around the shaft. Tighten the L knob. M • The blade guard (A) is fitted using 4 screws (L) and the support plate (M) as shown. CAUTION! Always use the recomm
Resumo do conteúdo contido na página número 14
ASSEMBLY Fitting a blade guard, grass blade Fitting the blade guard and saw and grass cutter (235R) blade (232R) • Secure the adapter (H) using the four screws (I). G F I E H D B A C • The blade guard (A) is fitted using 4 screws (L) as shown. CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. A L • Hook the blade guard/combination guard (A) onto the fitting on the shaft and secure with the bolt. CAUTION! Ensure that the guard
Resumo do conteúdo contido na página número 15
ASSEMBLY arrow in the diagram shows the area where you should guard as possible. To tighten the nut, turn the spanner in operate the socket spanner when loosening or tightening the opposite direction to the direction of rotation (Caution! the nut. left-hand thread). • When loosening and tightening the saw blade nut, there is Fitting the blade guard and saw a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade (235R) bl
Resumo do conteúdo contido na página número 16
ASSEMBLY • Place the cover (I) and the support flange (F) on the • Screw on the trimmer head (H) in the opposite direction to output shaft. the direction of rotation. • Fit the nut (G). Tighten the nut to a torque of 35-50 Nm H (3.5-5 kpm). Use the socket spanner in the tool kit. Grasp the handle of the spanner as close to the trimmer guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left- hand thread). • Tighten the trim
Resumo do conteúdo contido na página número 17
ASSEMBLY Spreading the load on your shoulders Fitting other guards and cutting A well-adjusted harness and machine makes work much attachments (235R) easier. Adjust the harness for the best working position. • Fit the trimmer guard/combination guard (A) intended for Tension the side straps so that the weight is evenly distributed use with the trimmer head/plastic blades. CAUTION! across both shoulders. Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A)
Resumo do conteúdo contido na página número 18
FUEL HANDLING Gasoline Fuel safety Never start the machine: 1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporate. CAUTION! Always use a quality gasoline/oil mixture with an octane rating of at least 87 octane ((RON+MON)/2). If your 2 If you have spilt fuel on yourself or your clothes, change machine is equipped with a catalytic converter (see chapter your clothes. Wash any part of your body that has come in on Technical data) always use a good qualit
Resumo do conteúdo contido na página número 19
FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. WARNING! Taking the following precautions, will lessen the risk of fire: • Mix (shake) the fuel mixture thoroughly before filling the ! machine’s fuel tank. Do not smoke or place hot objects near fuel. Always shut off the
Resumo do conteúdo contido na página número 20
STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most WARNING! The complete clutch cover and common reason why cracks are formed is that sharp shaft must be fitted before the machine is ! corners have been formed at the bottom of the teeth while started, otherwise the clutch can come loose sharpening or that the blade has been used with dull and cause personal inju
