Manual do usuário Flymo Twist n Edge

Resumo do conteúdo contido na página número 1

g ge e
E Ed d
n n
t t
s s
w w
T T
IMPORTANT INFORMATION
Read before use
& retain for future reference

Resumo do conteúdo contido na página número 2

360º 1 Carton Contents Switch Lever Pivot Block Upper Shaft Lower Shaft Handle Electric Cable with Knob moulded on plug Washer Instruction Manual Bolt Nut (if applicable) Safety Guard Steady Handle IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this trimmer can be danger

Resumo do conteúdo contido na página número 3

2 4. Immediately disconnect from the mains electricity 2. Avoid operating your trimmer in wet grass, where supply if the cable is cut, or the insulation is dam- feasible. aged. Do not touch the electric cable until the elec- 3. Take care in wet grass, you may lose your footing. trical supply has been disconnected. Do not repair 4. On slopes, be extra careful of your footing and wear a cut or damaged cable. Replace it with a new one. non-slip footwear. 5. Your extension cable must be uncoiled

Resumo do conteúdo contido na página número 4

3 Assembly Instructions A Shaft Assembly (A) 1. Locate the lower shaft (A1) into the upper 2 shaft (A2). 1 2. Grasp firmly and hold steady the lower shaft. Locate the upper shaft and snap together firmly. • The unit is correctly assembled when the gap between the upper and lower shaft has been closed. 2 1 B 1 2 3 Safety Guard Assembly (B) & (C) 1. Align the arrow on the top of the safety guard (B1) with the arrow on the side of the trimmer (B2). 2. Locate the safety guard (B3) over the cutting h

Resumo do conteúdo contido na página número 5

4 Double Auto Feed System How the automatic line feed works (H) H 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the two nylon lines hit the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before trimming or edging. 3. If the noise of the nylo

Resumo do conteúdo contido na página número 6

5 Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No ing? SEE “MANUAL LINE FEED” OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. SEE OR cleat? “CUTTING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is th

Resumo do conteúdo contido na página número 7

6 Cutting Head cont. To replace nylon line. S For your convenience it is recommended you buy spool and upper section line complete. Nylon line only is also available. Both are available from Electrolux Outdoor Products stockists. • If you have spool and line complete, follow steps 5 to 11. • If you have nylon line only, follow the full procedure below. • IMPORTANT Always wind the line onto the upper section of the spool first. • Remember! Your Flymo Trimmer is designed to use only nylon lin

Resumo do conteúdo contido na página número 8

Service Recommendations 1. We strongly recommend that your product is serviced at least every Centre, it is important to take your complete machine including twelve months, more often in a professional application. cable and any extension cables used. 2. Always use genuine Flymo Spare Parts. A network of specialist dealers can be found in your local Yellow 3. Prepacked spares are available from most Electrolux Outdoor Pages. To obtain service on your Flymo product simply telephone or Products s