Resumo do conteúdo contido na página número 1
Sabre Trim
For all customer enquiries or for replacement parts, contact:-
☎ ☎ 01325 300303
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
Resumo do conteúdo contido na página número 2
360º Carton Contents steady handle trimmer storage holder head steady handle instruction wheel manual screws x 2 screws x 4 Trimmer Head storage holder guard IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new product. IF ANY PARTS ARE MISSING CONTACT:- Husqvarna Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this product can be dangerous! This product can cause serious injury to
Resumo do conteúdo contido na página número 3
General 3. Take care in wet grass, you may lose your foot- ing. 1. Never allow children or people unfamiliar with these instructions to use the product. Local regulations may 4. On slopes, be extra careful of your footing and restrict the age of the operator. wear non-slip footwear. 2. Only use the product in the manner and for the 5. Do not walk backwards when trimming, you functions described in these instructions. could trip. Walk, never run. 3. Never operate the product when you are tired,
Resumo do conteúdo contido na página número 4
Assembly Instructions con’t E1 E2 E3 Attatching the Trimmer Head to the Sabre Handle 1. Push the Trimmer Head onto the Sabre Handle until you hear a click. (E1) 2. Push the Trimmer Head further onto the Sabre Handle until it reaches the mark shown in Fig E2. 3. Turn the Trimmer Head collar until it is secure. (E3) F3 F1 F2 Fitting the Steady Handle 1. Squeeze the lever on the steady handle (F1) 2. Attach the steady handle to product by releasing the lever and letting the handle latches fix into
Resumo do conteúdo contido na página número 5
Auto Line Feed System How the automatic line feed works (H) H 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the nylon line hits the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before trimming or edging. 3. If the noise of the nylon line b
Resumo do conteúdo contido na página número 6
How to trim and edge • WARNING J • The use of eye protection is recommended. Do not lean over the trimmer whilst trimming or edging, objects may be thrown by the cutting line. Do not allow cutting head to rest on the ground. Do not overload your trimmer. Overloading can be avoided by making sure the motor speed does not drop unduly. • BEFORE USE Make sure that the cutting line is fed out. • Make sure motor is up to full speed before trim- ming or edging. L K To start your Product 1. Attach yo
Resumo do conteúdo contido na página número 7
Manual line feed S To manually feed the nylon line (S) 1. If required line can be fed out manually. 2. To operate, press and release manual line feed but- ton, whilst gently pulling on the line until it reaches the line cutter. 3. If the line extends past the line cutter, too much line has been fed out. 4. If too much line is fed out, remove the spool cap and click spool anti-clockwise until the line is at the desired length. manual line feed button Cutting Head To remove spool cap T Cap 1. Pres
Resumo do conteúdo contido na página número 8
Maintenance X1 X2 • WARNING Cutting head continues to rotate after the trim- mer has been switched off. Keep fingers and hands clear of the line cutter on leading edge of guard. Caring for your product After you have finished using your product follow the pro- cedure below: X3 1. Never clean your trimmer with water, cleaning fluids, or solvents, just remove debris with a suitable tool, a soft brush or dry cloth. 2. Using a soft brush, clean around the inside of the safety guard, the cutting hea
Resumo do conteúdo contido na página número 9
Fault Finding Chart FAULT CHECK ACTION Is the automatic line feed work- Manually feed out line. LINE NOT FEEDING No ing? SEE “MANUAL LINE FEED” OR Is the line fed out and visible? Remove cap and spool, free line LINE TOO SHORT Has line been removed from No and re-fit spool and cap. SEE OR cleat? “CUTTING HEAD” TRIMMER VIBRATES The line may be jammed on the spool. Rewind line to remove Is the manual line feed working? No crossed loops. Check that line is in correct section of spool. Has the mot
Resumo do conteúdo contido na página número 10
Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture Failures due to the following are not covered, therefore it is important that within the guarantee period, Husqvarna Outdoor Products, you read the instructions contained in this Operator's Manual and under- through its Authorised Service Repairers will effect the repair or stand how to operate and maintain your machine: replacement to the customer free of charge providing: Failures not covered by guarant