Manual do usuário Flymo Multi-Trim Edger And

Resumo do conteúdo contido na página número 1

T TRIM RIM M MODE ODE E EDGE DGE M MODE ODE
TURN OVER
TURN OVER
TO EDGE
TO EDGE
IMPORTANT INFORMATION
Read before use
& retain for future reference

Resumo do conteúdo contido na página número 2

360º 1 Carton Contents Lock off Button Switch Lever Steady Handle Upper Shaft Electric Cable with moulded on plug Lower Shaft Safety Guard Instruction Manual IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:- Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this trimmer can be dangerous! This trimmer can cause serious inj

Resumo do conteúdo contido na página número 3

2 4. Immediately disconnect from the mains electricity sup- 2. Avoid operating your trimmer in wet grass, where feasible. ply if the cable is cut, or the insulation is damaged. Do 3. Take care in wet grass, you may lose your footing. not touch the electric cable until the electrical supply 4. On slopes, be extra careful of your footing and wear has been disconnected. Do not repair a cut or dam- non-slip footwear. aged cable. Replace it with a new one. 5. Do not walk backwards when trimming ,

Resumo do conteúdo contido na página número 4

3 Assembly Instructions A 1 2 3 Shaft Assembly (A) Cable Protection 1. Locate the lower shaft (A1) into the upper Sleeve shaft (A2). Note: the black internal cable and cable 1 protection sleeve (A3) are self-locating 2. Grasp firmly and hold steady the lower shaft. Locate the upper shaft and snap together firmly. • The unit is correctly assembled when the 2 gap between the upper and lower shaft has been closed. Safety Guard Assembly (B) & (C) B 4 3 1. Align the arrow on the top of the safety gua

Resumo do conteúdo contido na página número 5

4 Double Auto Feed System How the automatic line feed works (F) F 1. When initially switching on the trimmer, a small length of line is fed out. 2. A ‘clattering’ noise will be heard when the two nylon lines hit the line cutter. DO NOT BE ALARMED this is quite normal. After approximately 5 seconds the line will be cut to the correct length and the noise will reduce as the motor reaches full speed. • Make sure the motor is up to full speed before trimming or edging. 3. If the noise of the nylo

Resumo do conteúdo contido na página número 6

5 Fault Finding Chart WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment. FAULT CHECK ACTION Manually feed out line. Is the automatic line feed working? LINE NOT FEEDING No SEE “MANUAL LINE FEED” OR Remove cap and spool, free line and LINE TOO SHORT Is the line fed out and visible? re-fit spool and cap. SEE “SPOOL No OR CAP AND NYLON LINE” TRIMMER VIBRATES The line may be jammed on the spool. Is the manual line feed work- No Rewind line to remo

Resumo do conteúdo contido na página número 7

6 Spool cap and nylon line cont’ To replace nylon line. Q For your convenience it is recommended you buy spool and upper section line complete. Nylon line only is also available. Both are available from Electrolux Outdoor Products stockists. • If you have spool and line complete, follow steps 5 to 11. • If you have nylon line only, follow the full procedure below. • IMPORTANT Always wind the line onto the upper section of the spool first. • Remember! Your Flymo Trimmer is designed to use on

Resumo do conteúdo contido na página número 8

Service Recommendations 1. We strongly recommend that your product is serviced at least Service Centre, it is important to take your complete every twelve months, more often in a professional application. machine including cable and any extension cables used. 2. Always use genuine Flymo Spare Parts. A network of specialist dealers can be found in your local Yellow 3. Prepacked spares are available from most Electrolux Pages. To obtain service on your Flymo product simply tele- Outdoor Products