Resumo do conteúdo contido na página número 1
AT-IFS802SP/POE
8x10/100TX POE Layer 2 Managed Industrial Switch
AT-IFS802SP/POE Installation and
User’s Guide
613-001691 Rev.A
Resumo do conteúdo contido na página número 2
Copyright © 2012 Allied Telesis, Inc. All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc. Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners. Allied Telesis, Inc. reserves the right to make changes in specifications and other informa
Resumo do conteúdo contido na página número 3
Electrical Safety and Emissions Standards This product meets the following standards. U.S. Federal Communications Commission Radiated Energy Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy a
Resumo do conteúdo contido na página número 4
4
Resumo do conteúdo contido na página número 5
Preface This manual is the installation and management guide for the AT-IFS802SP/POE 8x10/100TX POE Layer 2 Managed Industrial Switch. The instructions in this guide explain how to install the switch, start a management session, and use the CLI and web management interfaces. Allied Telesis Contact Information If you need assistance with this product, you may contact Allied Telesis technical support by going to the Support & Services section of the Allied Telesis web site at www.alliedtelesi
Resumo do conteúdo contido na página número 6
Preface 6
Resumo do conteúdo contido na página número 7
AT-IFS802SP/POE(W)-80 User Manual 3 Content Chapter 1 Introduction .........................................................................6 1.1 Hardware Features ....................................................................................................................6 1.2 Software Features .......................................................................................................................8 1.3 Package Contents ..................................................
Resumo do conteúdo contido na página número 8
4 AT-IFS802SP/POE(W)-80 User Manual 6.9 Fault Relay Alarm ........................................................................................................................36 6.10 SNTP Configuration ................................................................................................................36 6.11 IP Security ..................................................................................................................................39 6.12 User Authentication ..
Resumo do conteúdo contido na página número 9
AT-IFS802SP/POE(W)-80 User Manual 5 System Commands Set......................................................................................................................79 Port Commands Set ..........................................................................................................................81 Trunk Commands Set ........................................................................................................................83 VLAN Commands Set .....................
Resumo do conteúdo contido na página número 10
6 AT-IFS802SP/POE(W)-80 User Manual Chapter 1 Introduction The 8 10/100TX + 2 10/100/1000T/Mini-GBIC Combo with 8 PoE Injectors Managed Industrial Switch is a cost-effective solution and meets the high reliability requirements demanded by industrial applications. Using fiber por t can extend the connection distance that incr eases the netw ork elasticity and perf ormance . Besides, the industrial switch provides the PoE function for kinds of Powered Devices to receive power as
Resumo do conteúdo contido na página número 11
AT-IFS802SP/POE(W)-80 User Manual 7 10Base-T: 2-pair UTP/STP Cat. 3, 4, 5/ 5E cable EIA/TIA-568 100-ohm (100m) 100Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable Network Cable EIA/TIA-568 100-ohm (100m) 1000Base-TX: 2-pair UTP/STP Cat. 5/ 5E cable EIA/TIA-568 100-ohm (100m) Distance: Multi mode: 0 to 5 km, 1300 nm (50/125 μm, 800 MHz*km) 0 to 4 km, 1300 nm (62.5/125 μm, 500 MHz*km) Single mode: 0 to 40 km, 1310 nm (9/125 μm, 3.5 PS/(nm*km)) 0 to 80 km, 1550 nm (9/125 μm, 19 PS/(nm*km)) Optical Fiber Mi
Resumo do conteúdo contido na página número 12
8 AT-IFS802SP/POE(W)-80 User Manual FCC Class A, CE EN61000-4-2, CE EN61000-4-3, CE EN-61000-4-4, CE EN61000-4-5, EMI CE EN61000-4-6, CE EN61000-4-8, CE EN61000-4-11, CE EN61000-4-12, CE EN61000-6-2, CE EN61000-6-4 Safety UL, cUL, CE/EN60950-1 Stability Testing IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock), IEC60068-2-6 (Vibration) 1.2 Software Features Management SNMP v1 v2c, v3/ Web/Telnet/CLI RFC 1215 Trap, RFC1213 MIBII, RFC 1157 SNMP MIB, RFC 1493 Bridge MIB, SNMP MIB RFC 2674 VLAN
Resumo do conteúdo contido na página número 13
AT-IFS802SP/POE(W)-80 User Manual 9 Login Security Supports IEEE802.1X Authentication/RADIUS Suppor t ingr ess pack et filter and egr ess pack et limit The egress rate control supports all of packet type and the limit rates are 100K~102400Kbps(10/100), 100K~256000Kbps(1000) Bandwidth Ingr ess filter pack et type combination rules ar e Br oadcast/Multicast/Unkno wn Control Unicast packet, Broadcast/Multicast packet, Broadcast packet only and all of pack et. The pack et filter rate can be se
Resumo do conteúdo contido na página número 14
10 AT-IFS802SP/POE(W)-80 User Manual Chapter 2 Hardware Description In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling information, and wiring installation. 2.1 Physical Dimension 8 10/100TX w/ X-Ring Managed Industrial Switch dimension (W x D x H) is 72mm x 105mm x 152mm 2.2 Front Panel The Front Panel of the 8 10/100TX w/ X-Ring Managed Industrial Switch is shown as below: Front Panel of the industrial switch
Resumo do conteúdo contido na página número 15
AT-IFS802SP/POE(W)-80 User Manual 11 2.3 Bottom View The bottom panel of the 8 10/100TX w/ X-Ring Managed Industrial Switch has one terminal block connector of two DC power inputs and one fault alarm. Bottom Panel of the industrial switch
Resumo do conteúdo contido na página número 16
12 AT-IFS802SP/POE(W)-80 User Manual 2.4 LED Indicators The diagnostic LEDs that provide real-time information of system and optional status are located on the front panel of the industrial switch. The following table provides the description of the LED status and their meanings for the switch. LED Color Status Meaning On The switch unit is power on PWR Green Off No power On The industrial switch is the master of X-Ring group R.M. Green Off The industrial switch is not a ring master in X-Rin
Resumo do conteúdo contido na página número 17
AT-IFS802SP/POE(W)-80 User Manual 13 Chapter 3 Hardware Installation In this paragraph, we will describe how to install the 8 10/100TX w/ X-Ring Managed Industrial Switch and the installation points attended to it. 3.1 Installation Steps 1. Unpack the Industrial switch 2. Check if the DIN-Rail is screwed on the Industrial switch or not. If the DIN-Rail is not screwed on the Industrial switch, please refer to DIN-Rail Mounting section for DIN-Rail installation. If users want to wall mount th
Resumo do conteúdo contido na página número 18
14 AT-IFS802SP/POE(W)-80 User Manual 3.2 DIN-Rail Mounting The DIN-Rail is screwed on the industrial switch when out of factory. If the DIN-Rail is not screwed on the industrial switch, please see the following pictures to screw the DIN-Rail on the switch. Follow the steps below to hang the industrial switch. 1. First, insert the top of DIN-Rail into the track. 2. Then, lightly push the DIN-Rail into the track. 3. Check if the DIN-Rail is tightened on the track or not. 4. To remove the
Resumo do conteúdo contido na página número 19
AT-IFS802SP/POE(W)-80 User Manual 15 3.3 Wall Mount Plate Mounting Follow the steps below to mount the industrial switch with wall mount plate. 1. Remove the DIN-Rail from the industrial switch; loose the screws to remove the DIN-Rail. 2. Place the wall mount plate on the rear panel of the industrial switch. 3. Use the screws to screw the wall mount plate on the industrial switch. 4. Use the hook holes at the corners of the wall mount plate to hang the industrial switch on the wall. 5. To remo
Resumo do conteúdo contido na página número 20
16 AT-IFS802SP/POE(W)-80 User Manual 3.4 Wiring the Power Inputs Please follow the steps below to insert the power wire. 1. Insert AC or DC power wires into the contacts 1 and 2 for power 1, or 5 and 6 for power. 2. Tighten the wire-clamp screws for preventing the wires from loosing. The wire gauge for the terminal block should be in the range between 12 ~ 24 [note] AWG.
