Resumo do conteúdo contido na página número 1
ISS 408
Integration Seamless Switcher
68-575-01 Rev. G
02 08
Resumo do conteúdo contido na página número 2
Precautions Safety Instructions � English Warning Power sources � This equipment should be operated only from the power source indicated on the product. This This symbol is intended to alert the user of important operating and maintenance equipment is intended to be used with a main power system with a grounded (neutral) conductor. The (servicing) instructions in the literature provided with the equipment. third (grounding) pin is a safety feature, do not attempt to bypass or disable it. Th
Resumo do conteúdo contido na página número 3
FCC Class B Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarante
Resumo do conteúdo contido na página número 4
AUDIO AUDIO Quick Start — ISS 408 Integration Seamless Switcher Step 5 Installation Tip Cable the switcher for Sleeve Step 1 stereo audio input. Each Tip Sleeve input has a 3.5 mm, Turn off power to the ISS 408 and the input and 5-pole captive screw Unbalanced Input output devices, and remove the power cords from (high impedance) connector for balanced or them. Tip unbalanced stereo or Ring Sleeve (s) mono audio input. Step 2 Tip Connectors are included Ring If desired, install an optional DVI
Resumo do conteúdo contido na página número 5
Quick Start — ISS 408 Integration Seamless Switcher, cont’d 2. Press an input button to select the input to Step 9 configure. If desired, connect a control system or computer to the Remote RS-232 port. 3. Rotate the Adjust knob to select the input video type. 51 Pin RS-232 Function 4. Rotate the Adjust knob to select the input 1 — Not used audio gain or attenuation level. 2 TX Transmit data 3 RX Receive data 9 6 5. Select other inputs to configure as necessary 4 — Not used Female 5 Gnd Signal
Resumo do conteúdo contido na página número 6
Table of Contents Chapter 1 � Introduction ....................................................................................................... 1-1 About this Manual ............................................................................................................. 1-2 About the Switcher............................................................................................................ 1-2 Features .............................................................................
Resumo do conteúdo contido na página número 7
Table of Contents, cont’d Enhanced Mode submenu ................................................................................ 3-14 Pixel Phase submenu ......................................................................................... 3-14 Preview Switch Mode submenu ........................................................................ 3-14 .................................................................................... 3-15 PAL File Mode submenu Reset submenu ...................
Resumo do conteúdo contido na página número 8
Using the Command/Response Table ........................................................................ 4-8 Command/response table for SIS commands .................................................................. 4-9 Command/response table for IP SIS commands ............................................................ 4-15 Command/response table for special function SIS commands ..................................... 4-16 Command/response table for advanced instruction Set commands .........
Resumo do conteúdo contido na página número 9
Table of Contents, cont’d Chapter 7 � Maintenance and Modifications .......................................................... 7-1 Opening and Closing the Switcher ............................................................................ 7-2 Installing a Firmware Upgrade .................................................................................... 7-4 Installing a DVI Output Card ......................................................................................... 7-5 Appendix A �
Resumo do conteúdo contido na página número 10
ISS 408 Integration Seamless Switcher Chapter One 1 Introduction About this Manual About the Switcher Features
Resumo do conteúdo contido na página número 11
Intr Intr oduction, cont’d oduction About this Manual This manual contains installation, configuration, and operating information for the Extron ISS 408 Integration Seamless Switcher. In this manual, the terms “switcher” and “ISS” are used interchangeably to refer to the ISS 408. � Chapter 1, “Introduction”, identifies the switcher’s features. � Chapter 2, “Installation”, details how to install the switcher. � Chapter 3, “Operation”, describes how to operate the switcher and use all of its featu
Resumo do conteúdo contido na página número 12
Several of the output resolutions and rates include Extron’s Accu-RATE Frame ™ ™ Lock (AFL ), a proprietary technology that locks the output frame rate to the input rate, solving the image tearing problem that can result from different input and output rates. The ISS 408 features HDTV 576p, 720p, 1080p, and 1080i outputs. Preview Monitor Program Monitor Projector Extron ISS 408 Control System (RS-232) LAN/WAN Network/ Internet DVD Player Codec Extron RGB 109xi VCR Laptop Podium PC Figure 1-1 —
Resumo do conteúdo contido na página número 13
Introduction, cont’d Features Inputs — Video inputs — The ISS switches among eight fully-configurable RGB, HDTV component video, component video, S-video, and composite video inputs on five BNC connectors per input. Audio inputs — The ISS switches among eight balanced or unbalanced stereo or mono audio inputs on 5-pole captive screw connectors. Outputs — Standard video outputs — The ISS outputs individually scaled video signals as RGBHV or RGBS. Two sets of BNC connectors and two 15-pin HD conn
Resumo do conteúdo contido na página número 14
Audio gain/attenuation — Users can set the input level of audio gain or attenuation (-24 dB to +9 dB) via the RS-232 port, Ethernet link, or from the front panel. Individual input audio levels can be adjusted so there are no noticeable volume differences between sources. Audio cross-fading — This transition technique is applied during switching to lower the audio level of the switched out source while simultaneously raising the audio level of the activated source. Ethernet port — Supports conne
Resumo do conteúdo contido na página número 15
Introduction, cont’d 1-6 ISS 408 Integration Seamless Switcher � Introduction
Resumo do conteúdo contido na página número 16
ISS 408 Integration Seamless Switcher Chapter Two 2 Installation Mounting the Switcher Cabling and Rear Panel Views Configuration
Resumo do conteúdo contido na página número 17
Installation, cont’d Installation Mounting the Switcher Four uninstalled rubber feet are included with the switcher. If you are going to rack mount the switcher, mount it before you cable it (see “Rack mounting”, below), and do not install the rubber feet. If you are not rack mounting the switcher, see “Tabletop placement”, below. Tabletop placement For tabletop placement, install the self-adhesive rubber feet/pads (provided) onto the four corners of the bottom of the switcher. Rack mounting U
Resumo do conteúdo contido na página número 18
Mounting instructions To rack mount the switcher, use two screws on each end of the switcher to attach the switcher to the rack (see figure 2-1). Figure 2-1 — Mounting the switcher ISS 408 Integration Seamless Switcher � Installation 2-3 INPUTS BLACK 1 2 3 4 5 6 7 8 VIDEO CUT DISSOLVE MUTE 1 2 3 4 5 6 7 8 AUDIO ADJUST COLOR/ BRT/ SIZE CENTER FILTER TINT CONT MENU NEXT ISS 408 INTEGRATION SEAMLESS SWITCHER
Resumo do conteúdo contido na página número 19
LINK ACT Installation, cont’d Cabling and Rear Panel Views All connectors are on the rear panel (figure 2-2). 2 4 5 OUTPUTS INPUTS 12 3 4 5 6 7 8 PROGRAM PREVIEW PROGRAM R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R/R-Y R R PREVIEW DVI OUT G/Y G/Y G/Y G/Y G/Y G/Y G/Y G/Y G G VID VID VID VID VID VID VID VID B/C B/C B/C B/C B/C B/C B/C B/C B B B-Y B-Y B-Y B-Y B-Y B-Y B-Y B-Y RS-232 8 100- 240 50/60 Hz 1.2A MAX. H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV H/HV V V V V V V V V V V ETHERNET 1 23 4 5
Resumo do conteúdo contido na página número 20
LR LR Input audio connectors — Connect balanced or unbalanced stereo or mono 3 audio sources to these 3.5 mm, 5-pole captive screw connectors. Connectors are included with the seamless switcher, but you must supply the audio cable. Figure 2-4 shows how to wire a connector for the appropriate input type. High impedance is generally over 800 ohms. Tip Tip Sleeve Ring Sleeve (s) Tip Tip Ring Sleeve 0.2” (5 mm) max. Balanced Stereo Input Unbalanced Stereo Input (high impedance) (high impedance) Do
