Resumo do conteúdo contido na página número 1
User’s Guide
Shop online at
omega.com
e-mail: info@omega.com
For latest product manuals:
omegamanual.info
LV800 SERIES
Capacitance Point Level Sensors
Resumo do conteúdo contido na página número 2
® OMEGAnet Online Service Internet e-mail omega.com info@omega.com Servicing North America: U.S.A.: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: ® U.S.A. and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OME
Resumo do conteúdo contido na página número 3
LV800 SERIES This manual contains the information necessary to ensure a safe and successful installation. Please read and comply with the section on page 9 of this manual pertaining to SAFETY. Doing so will ensure proper oper- ation of the equipment and the safety of all personnel. Before discarding shipping container, please inspect it thoroughly and verify that all parts ordered are accounted for. Sometimes smaller parts become stuck under carton flaps and other packaging materials. 2
Resumo do conteúdo contido na página número 4
PRE-INSTALLATION CONSIDERATIONS Choosing a Location: (See Figure 2) 1) Material Flow - When selecting a location for the LV800, choose a point in the vessel where the probe will be out of the direct flow of incoming and outgoing material to prevent any mechanical damage that may be caused by the pres- sure of the flow. The LV800 must be positioned at a point where incoming material will reach and cover the probe in its normal flow, and when receding, will flow away from the
Resumo do conteúdo contido na página número 5
MECHANICAL INSTALLATION ELECTRICAL INSTALLATION Standard, Food Grade and Stub Probe Mounting: Factory Wiring: (See Figures 3 & 4) The LV800 probe wires are connected to the backside of the 1) Select a mounting location in accordance with the Pre- PCB. DO NOT alter this connection. Doing will likely cause Installation Recommendations. improper operation of the sensor. 2) If using a welded fitting, cut a hole into the side/top of the vessel corresponding to the mounting
Resumo do conteúdo contido na página número 6
Power Input: (See Figure5) 2-Step Calibration- probe exposed to material The LV800 is designed to accept either 115VAC or 230VAC 1) While the probe is not covered with material, rotate “Sense (factory set). Verify the intended voltage supply is compatible Adjust” clockwise just until “Sense” (yellow) LED turns on. with the voltage configuration indicated on the electronics and 2) Permit the application material to cover the probe. While the external nameplate. Connect pow
Resumo do conteúdo contido na página número 7
LV800 Figure 7 Delay: A potentiometer is provided for setting the time delay between the time material is "sensed" (Yellow LED on) and the time the relay contact output changes (Red LED on). Units have a 1- turn potentiometer. A clockwise rotation will increase the delay from .25 to 15 seconds. This adjustment minimizes false sig- nals associated with temporary material shifts. The delay between the time material is "not sensed" (Yellows LED off) and the time the relay cont
Resumo do conteúdo contido na página número 8
TROUBLESHOOTING MAINTENANCE PROBLEM: Sensor will not sense material Fuse Replacement: CAUSE/SOLUTION: The fuse incorporated into the LV800 PCB is not intended for 1) Verify power is applied to the sensor. operator replacement. A qualified technician can replace the 2) Verify "Sense Adjust." Reposition adjustment clockwise applicable fuse according to the following specifications. If nec- therefore making the probe more sensitive to "difficult to essary, c
Resumo do conteúdo contido na página número 9
MECHANICALS DIMENSIONS ARE SHOWN IN INCHES WITH MILLIMETER EQUIVALENT IN BRACKETS Standard Probe Stub Probe 8
Resumo do conteúdo contido na página número 10
SAFETY SPECIFICATIONS ± ± Power: 115VAC ( 15%); 2.5VA; 50/60Hz / 230VAC ( 15%); 2.5VA; 50/60Hz General Safety Altitude: 6562 ft (2000 m) max Installation Category: II CAUTION: It is essential that all instructions in this manual be followed to Pollution Degree: 4 (Reduced to 2 by enclosure) Suitable for indoor/outdoor use ensure proper operation of the equipment and safety of operating person- Ambient Op Temp: -40˚ F (-40˚ C) to +150˚ F (+65˚
Resumo do conteúdo contido na página número 11
WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Serv
Resumo do conteúdo contido na página número 12
Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE MU Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies MU Wire: Thermocouple, RTD & Thermistor MU Calibrators & Ice Point References MU Recorders, Controllers & Process Monitors MU Infrared Pyrometers PRESSURE, STRAIN AND FORCE MU Transducers & Strain Gages MU Load Cells & Pressure Gages MU Displacement Transducers MU Instrumentation & Accessories FLOW
