Resumo do conteúdo contido na página número 1
OWNER’S MANUAL
AND
INSTALLATION GUIDE
ACC56M
10-DISC CD CHANGER
Visit us at www.asaelectronics.com to see our full line of mobile audio and video products.
MADE IN CHINA
Resumo do conteúdo contido na página número 2
I N T R O D U C T I O N Congratulations on your purchase of the AQUATRONICS ACC56M REMOTE-CONTROL 10-DISC CD CHANGER. This system allows you to easily upgrade your existing audio system to include a quality CD entertainment function. Best of all, the CD Changer is easy to install. There is only one cable to plug in to the rear of the already equipped radio. Just follow the simple step-by-step instructions that follow. F E A T U R E S Remote mount changer holds up to 10 compact discs. Advanced
Resumo do conteúdo contido na página número 3
PACKING LIST BEFORE INSTALLING THE UNIT Transport Lock Screws Main Unit R E A R The mechanism in the CD changer is "locked" into place during shipment by three transport lock screws. Be sure to remove the screws prior to installation. F R O N T CAUTION: After removing the transport lock screws, place the B O T T O M supplied seals (A) over the screw holes. These seals are used to keep dust out of the unit, which TRANSPORT LOCK SCREWS could cause a malfunction. (2 RIGHT SIDE,1 LEFT SIDE) lnstall
Resumo do conteúdo contido na página número 4
WHERE TO INSTALL THE CHANGER I N S T A L L A T I O N The ACC56M changer is designed for horizontal (flat), vertical (upright) or 45-degree A few of the many mounting possibilities are shown below. The following precautions must mounting. It must never be mounted upside-down or on either one of it's sides as explained be considered when selecting the mounting location. previously. The position of the built-in anti-vibration springs (left and right side), must Installation Cautions and Warnings: c
Resumo do conteúdo contido na página número 5
PROCEDURE FOR VERTICAL INSTALLATION PROCEDURE FOR HORIZONTAL INSTALLATION N O T E : If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 6), start with step 2. Attach bracket (L) and bracket (R) to each side of the unit,using the hexagonal bolts with washer base (M5 x 10). Attach bracket (L) and bracket (R) to Set the 4 anti-vibration springs to Anti-vibration each side of the unit, using the position “v” springs position hexagonal bolts
Resumo do conteúdo contido na página número 6
PROCEDURE FOR 45 ANGLE INSTALLATION OVERALL WIRING VIEW This page is provided to give you a quick look at the entire wiring of the ACC56M. Use it to N O T E : If the anti-vibration spring position has been changed and verified for 45 a n g l e plan your wire routing paths and possible connection points. Detailed wiring is explained in mounting (as shown on page 6), start with step 2. the following pages. Set the 4 anti-vibration springs to Attach bracket (L) and bracket (R) to position “45°
Resumo do conteúdo contido na página número 7
HINTS FOR CORRECT AND SAFE OPERATION HANDLING THE DISCS This CD Changer is designed to be operated only on 12 volt DC negative ground systems. Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of The unit cannot be used on 24 volt or positive ground systems. sound quality. To take proper care of your discs: Temperature 1.Use compact discs that have the logo. The unit may not operate correctly in extremely hot or cold temperatures. It is equippe
Resumo do conteúdo contido na página número 8
USE OF THE CD MAGAZINE Loading The Magazine Into The Changer Loading Disc Into The Magazine Fig. 1 Completely slide the door on the changer to the This CD Changer uses a specially-designed maga Fig. 4 right as shown in Figure 4. Making sure the top of zine to hold up to 10 compact discs. To load discs the magazine is facing upward,gently insert it into into the magazine, grip the tab on the magazine the unit until it clicks into place, as shown in tray into which you will be loading a disc and
Resumo do conteúdo contido na página número 9
SPECIFICATIONS T R O U B L E S H O O T I N G An error made in operation or during installation of this product may be mistaken for a Changer system malfunction. Please perform the checks described below before contacting your Frequency Response 5 - 20,000 Hz ±1dB dealer or service facility. Distortion 0.008% @ 1kHz Possible Cause Remedy Symptom Dynamic Range 95 dB Check fuses in vehicle fuse box and changer system. Signal-to-Noise Ratio 95 dB Replace as necessary with fuse of Blown fuse Chan
Resumo do conteúdo contido na página número 10
1 6
