Resumo do conteúdo contido na página número 1
cover 2008.8.21 12:21 PM 페이지 2
OPERATING INSTRUCTIONS
RD-6513
AUDIO/VIDEO RECEIVER
Resumo do conteúdo contido na página número 2
RD-6513(A) 2008.8.21 12:19 PM 페이지 3 IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 12. Use only with the cart, stand, tripod, bracket, or table 2. Keep these instructions. specified by the manufacturer, or sold with the 3. Heed all warnings. apparatus. 4. Follow all instructions. When a cart is used, use caution when moving the 5. Do not use this apparatus near water. cart/apparatus combination to avoid injury from tip-over. 6. Clean only with dry cloth. 7. Do not block any ventila
Resumo do conteúdo contido na página número 3
RD-6513(A) 2008.8.21 12:19 PM 페이지 4 Introduction READ THIS BEFORE OPERATING YOUR UNIT This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. TO REDUCE THE RISK OF ELECTRIC SHOCK, CAUTION : This symbol is intended to alert the user to the presence DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER of important operating
Resumo do conteúdo contido na página número 4
RD-6513(A) 2008.8.21 12:19 PM 페이지 5 CONTENTS • IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................................. 3 Introduction • READ THIS BEFORE OPERATING YOUR UNIT ................................................................................................................. 4 System Connections ........................................................................................................
Resumo do conteúdo contido na página número 5
RD-6513(A) 2008.8.21 12:19 PM 페이지 6 System Connections • Do not plug the AC input cord into the wall AC outlet until all connections are completed. • Be sure to observe the color coding when connecting audio, video and speaker cords. • Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver. 1. CONNECTING ANTENNAS • Change the position of the FM indoor antenna until you • A 75 Ω outdoor FM antenna may be used to further get the best reception
Resumo do conteúdo contido na página número 6
RD-6513(A) 2008.8.21 12:19 PM 페이지 7 2. CONNECTING VIDEO COMPONENTS • The jacks of VIDEO 1 may also be connected to a DVD recorder or other digital video recording component. For details, refer to the operating instructions of the component to be connected. • The jacks of VIDEO 2 can also be connected to an additional video component such as a cable TV tuner, an LD player or satellite system. • There are three types of video jacks (COMPONENT, S-VIDEO, (composite) VIDEO) for analog video conn
Resumo do conteúdo contido na página número 7
RD-6513(A) 2008.8.21 12:19 PM 페이지 8 3. CONNECTING AUDIO COMPONENTS • The TAPE IN/OUT jacks can be connected to audio recording equipment such as a tape deck, an MD recorder, etc. 4. CONNECTING EXTERNAL INs • Use these jacks to connect the corresponding analog outputs of 6 CH decoder or DVD player with 6 CH output for Dolby Digital or DTS, etc. (For details, see the operator's manual of the component to be connected.) 8 ENGLISH
Resumo do conteúdo contido na página número 8
RD-6513(A) 2008.8.21 12:19 PM 페이지 9 5. CONNECTING DIGITAL INs • The OPTICAL and the COAXIAL DIGITAL OUTs of the components that are connected to CD and VIDEO 1 ~ VIDEO 2 of this unit can be connected to these DIGITAL INs. • A digital input should be connected to the components such as a CD player, LD player, DVD player, etc. capable of outputting DTS Digital Surround, Dolby Digital or PCM format digital signals, etc. • For details, refer to the operating instructions of the component connect
Resumo do conteúdo contido na página número 9
RD-6513(A) 2008.8.21 12:19 PM 페이지 10 8. AC INPUT CORD • Plug the cord into a wall AC outlet. Speaker placement Ideal speaker placement varies depending on the size of your room and the wall coverings, etc. The typical example of speaker placement and recommendations are as follows : Front left and right speakers and center speaker • Place the front speakers with their front surfaces as flush with TV or monitor screen as possible. • Place the center speaker between the front left and right
Resumo do conteúdo contido na página número 10
RD-6513(A) 2008.8.21 12:19 PM 페이지 11 Front Panel Controls 1. POWER switch 11. HEADPHONE jack 21. MEMORY/ENTER button 2. POWER ON/STANDBY button 12. SPEAKER button/indicator 22. TUNING UP/DOWN (+/-) buttons 3. STANDBY indicator 13. REMOTE SENSOR 23. PRESET UP/DOWN (+/-) buttons 4. FLUORESCENT DISPLAY 14. SURROUND MODE button 24. SETUP MIC JACK For details, see below. 15. STEREO button For details, see next page. 5. VIDEO INPUT SELECTOR button 16. DISPLAY button 25. FRONT AUX IN JACK 6. AUDIO
Resumo do conteúdo contido na página número 11
RD-6513(A) 2008.8.21 12:19 PM 페이지 12 SETUP MIC JACK • To use Auto Setup function, connect the supplied microphone to the SETUP MIC jack.(For details, refer to "When selecting the AUTO SETUP" on page 35.) Notes: • Because the microphone for Auto Setup is designed for use with this receiver, do not use a microphone other than the one supplied with this receiver. • After you have completed the auto setup procedure, disconnect the microphone. Microphone FRONT AUX IN JACK • The FRONT AUX IN ja
Resumo do conteúdo contido na página número 12
RD-6513(A) 2008.8.21 12:19 PM 페이지 13 Remote Controls Note : • Some buttons (USB, VIDEO 3, AUX and USB transport buttons) are not available for this receiver. 13 ENGLISH
Resumo do conteúdo contido na página número 13
RD-6513(A) 2008.8.21 12:19 PM 페이지 14 REMOTE CONTROL OPERATION RANGE • Use the remote control unit within a range of about 7 meters (23 feet) and angles of up to 30 degrees aiming at the remote sensor. LOADING BATTERIES 1. Remove the cover. 2. Load two batteries ("AAA" size, 1.5 V) matching the polarity. • Remove the batteries when they are not used for a long time. • Do not use the rechargeable batteries (Ni-Cd type). 14 ENGLISH
Resumo do conteúdo contido na página número 14
RD-6513(A) 2008.8.21 12:19 PM 페이지 15 Operations Note : Before operating this receiver, first set this unit as desired for optimum performance, doing the system setup procedures. (For details, refer to "System Setup" on page 29.) LISTENING TO A PROGRAM SOURCE Before operation • Enter the standby mode. 3. Select the desired input source. • The STANDBY indicator lights up. This means that the receiver is not disconnected from the AC mains and a small amount of current is retained to support the
Resumo do conteúdo contido na página número 15
RD-6513(A) 2008.8.21 12:19 PM 페이지 16 When CD, VIDEO 1~ 2 is selected as an input source 4. Select the digital or the analog input connected 7. To mute the sound. as desired. • Each time this button is pressed, the corresponding input is selected as follows: • “MUTE” will flicker. • To resume the previous sound level, press it again. → o(ptical) → c(oaxial)1→ c(oaxial) 2 → A(nalog) Notes : • When F AUX, TAPE, BT IN, EXT IN or tuner is selected as an input source, the digital input cannot be
Resumo do conteúdo contido na página número 16
RD-6513(A) 2008.8.21 12:19 PM 페이지 17 When the TONE is set to ON to adjust the tone Adjusting the tone (bass and treble) (bass and treble). 9. Enter the tone mode. 11. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired tone. • Each time these buttons are pressed, the tone is selected as follows : • The tone mode is displayed for several seconds. → BASS ↔ TRBL (treble) ↔ TONE : ON ← 10. Press the CURSOR LEFT(◀)/RIGHT(▶) 12. Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select t
Resumo do conteúdo contido na página número 17
RD-6513(A) 2008.8.21 12:19 PM 페이지 18 SURROUND SOUND • This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. Surround modes • The following modes apply conventional 2-channel ■DTS Digital Surround signals such as digital PCM or analog stereo signals to DTS Digital Surround(also called simply DTS) is a multi- high performance Digital Signal Processor to recreate channel digital sig
Resumo do conteúdo contido na página número 18
RD-6513(A) 2008.8.21 12:19 PM 페이지 19 ENJOYING SURROUND SOUND Notes: • Before surround playback, first perform the speaker setup procedure, etc. on the SETUP menu for optimum performance. (For details, refer to "SETTING THE SPEAKER SETUP" on page 34.) • When the EXTERNAL IN is selected as an input source, the surround modes cannot be selected. When CD or VIDEO 1 ~ 2 is selected as an input source Select the auto surround mode or the manual surround mode depending on how to select a surround
Resumo do conteúdo contido na página número 19
RD-6513(A) 2008.8.21 12:19 PM 페이지 20 When adjusting the sound parameters • While playing digital signals from Dolby Digital or DTS program source or listening in Dolby Pro Logic II Music mode, you can adjust their parameters for optimum surround effect. 1. Press the SOUND PARAMETER button. • Then "DRC : ~ " (or "PANO : ~ ") is displayed for several seconds. • If the parameter mode disappears, press this button again. 2. Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired parameter. •
Resumo do conteúdo contido na página número 20
RD-6513(A) 2008.8.21 12:19 PM 페이지 21 Adjusting each channel level with test tone • The volume level of each channel can be adjusted easily with the test tone function. Note : When the SPEAKER button is set to off, the test tone function does not work. 1. Enter the test tone mode. • The test tone mode is displayed and will be heard from the speaker of each channel for 2 seconds as follows: → FL → C → FR → SR → SL → SW Front Left Center Front Right Surround Right
