Resumo do conteúdo contido na página número 1
Amplifier
X1.1000.1D
X1.2000.1D
X1.400.2
X1.800.4
Installation & Operation
Installation et fonctionnement
Instalación y operación
Einbau und Betrieb
Installazione e funzionamento
Resumo do conteúdo contido na página número 2
Introduction INNOVATE OR DISINTIGRATE Thank you for purchasing the Lightning Audio Storm Amplifier. Our customers have come to expect that Lightning Audio pushes the edge in audio. Now we will push the edge in the amplifier and woofer business with high value and high performance models. If, after reading your manual, you still have questions regarding this product, we recommend that you see your Lightning Audio dealer. If you need further assistance, you can call us direct at 1- 888-881-8186. B
Resumo do conteúdo contido na página número 3
PRACTICE SAFE SOUND™ Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High powered auto sound systems may produce sound pressure levels well over 130dB. Use common sense and practice safe sound. Safety Instructions This symbol with “WARNING” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in severe injury or death. This symbol with “CAUTION” is intended to alert the user to the presence
Resumo do conteúdo contido na página número 4
Design Features A. RCA Input Jacks – Line Level from Radio Pre-outs: The industry standard RCA jack provides an easy connection for signal level input. They are platinum to resist the signal degradation caused by corrosion. B. Gain Control: The input gain control is preset to match the output of most source units. They can be adjusted to match output levels from a variety of source units. C. Adjustable Crossover Frequency Control: 50-250Hz. Low Pass only on Models X1.1000.1D & X1.2000.1D. D. Sp
Resumo do conteúdo contido na página número 5
Installation This section focuses on some of the vehicle considerations for installing your new Amplifier. Pre- planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments. CAUTION: If you feel unsure about installing this system yourself, have it ! installed by a qualified technician. CAUTION: Before installation, disconnect the battery negative (-) te
Resumo do conteúdo contido na página número 6
Installation WIRING THE SYSTEM CAUTION: If you do not feel comfortable with wiring your new unit, please see ! your local Authorized Lightning Audio Dealer for installation. CAUTION: Before installation, disconnect the battery negative (-) terminal to ! prevent damage to the unit, fire and/or possible injury. CAUTION: Avoid running power wires near the low level input cables, antenna, ! power leads, sensitive equipment or harnesses. The power wires carry substantial current and could induce nois
Resumo do conteúdo contido na página número 7
Installation MONO AMPLIFIERS X1.1000.1D & X1.2000.1D These amplifiers have two (2) speaker outputs for convenience and are paralleled internally. CAUTION: The X1.1000.1D and X1.2000.1D amplifiers are not recommended for ! impedance loads below 1Ω . X1.400.2 X1.1000.1D X1.800.4 X1.2000.1D 7
Resumo do conteúdo contido na página número 8
Installation From Source Unit From Source Unit X1.1000.1D X1.2000.1D From Source Unit From Source Unit X1.400.2 2-Channel – Bridged 2-Channel From Source Unit From Source Unit X1.800.4 4-Channel – 4-Channel Set as 3-Channel Bridged REMOTE LEVEL/BASS EQ CONTROL Mounting (Models X1.1000.1D & X1.2000.1D Only) Clip Mounting and installation 1. Find a location, either under the dash or near the center console, that gives easy access to the remote. 2. Using the screws supplied, install the mounting c
Resumo do conteúdo contido na página número 9
Installation USING PASSIVE CROSSOVERS A passive crossover is a circuit that L C uses capacitors and/or coils and is placed on speaker leads between the 6dB/Octave Low-Pass 6dB/Octave High-Pass amplifier and speaker. The crossover delegates a specific range of Speaker Impedance frequencies to the speaker for Freq. optimum driver performance. A 2 OHMS 4 OHMS 8 OHMS Hertz crossover network can perform one of three functions: High-Pass L C L C L C (capacitors), Low-Pass (inductors or coils) and Band
Resumo do conteúdo contido na página número 10
Operation ADJUSTING GAIN To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the distortion is inaudible. NOTE: For a more in depth setting procedure, contact Lightning Audio Technical S
Resumo do conteúdo contido na página número 11
Operation STRAPPING AMPLIFIERS (X1.2000.1D Only) The X1.2000.1D amplifiers have the ability to connect two together and have their outputs combined, or strapped, to power a single speaker load. CAUTION: Two X1.2000.1D amplifiers that are strapped together are not ! recommended for impedance loads below 2Ω . 1. Select which amplifier of the two will be the master. and set the Master/Slave switch in the "out" position. NOTE: Only adjustments made to the master amplifier will effect the output to t
Resumo do conteúdo contido na página número 12
Troubleshooting Symptom Diagnosis Remedy Amplifier does not B+ or REM not between 10.5 and Check the alternator, battery, fuse, turn on. 15.5 volts or no voltage present and wiring and repair as necessary Amplifier Noise Check wiring and repair as necessary Amplifier is not properly grounded. (Turn-On Pop) Voltage spike from source unit is Connect a relay turn-on module to entering amplifier’s input REM terminal if pops are eliminated with no input signal to amplifier Engine Noise Re-route sign
Resumo do conteúdo contido na página número 13
Limited Warranty Information Lightning Audio offers a limited warranty on products on the following terms: • Length of Warranty Speakers One year parts and labor warranty. Requires proof of purchase. Amplifiers Bolt: One year parts and labor warranty. Requires proof of purchase. Strike and Storm: One year parts and labor warranty. Requires proof of purchase. Or, Two years parts and labor warranty if installed by a Authorized Dealer. Requires proof of purchase. CT-1and PC2 One year parts and labo
Resumo do conteúdo contido na página número 14
Introduction L’innovation ou la mort ! Nous vous remercions d'avoir acheté cet ampli Lightning Audio Bolt. Notre clientèle s’attend à ce que Lightning Audio pousse toujours plus loin les limites du son. C’est ce à quoi nous nous consacrons à présent dans les domaines des amplis et des haut- parleurs graves grâce à des modèles hautement performants de valeur supérieure. Si vous avez encore des questions à propos de ce produit, même après avoir lu ce manuel, contactez votre concessionnaire Lightni
Resumo do conteúdo contido na página número 15
MD PRATIQUEZ UNE ÉCOUTE SANS RISQUES Une exposition continue à des niveaux de pression acoustique supérieurs à 100 dB peut causer une perte d'acuité auditive permanente. Les systèmes audio de forte puissance pour auto peuvent produire des niveaux de pression acoustique bien au-delà de 130 dB. Faites preuve de bon sens et pratiquez une écoute sans risque ´ ´ Consignes de securite Le symbole accompagnant le mot « AVERTISSEMENT » signale à l'utilisateur la présence d’instructions importantes. Le no
Resumo do conteúdo contido na página número 16
´ Particularites Techniques A. Prises d’entrée RCA – Entrées de ligne de pré-sorties radio : les prises RCA de norme industrielle permettent une connexion facile pour les entrées de signaux. Elles sont plaquées de platine pour résister à la détérioration de signal due à l'effet de la corrosion. B. Commande de gain : la commande de gain d'entrée est préréglée de manière à correspondre à la sortie de la plupart des unités source. Elle peut être réglée en fonction d'une variété d'unités source. C.
Resumo do conteúdo contido na página número 17
Installation Cette section traite de points concernant le véhicule dont il faut tenir compte pour l’installation de votre nouvel ampli. Vous sauverez du temps en planifiant à l’avance la disposition du système et du câblage. Assurez-vous, entre autres, que chaque composant du système est facilement accessible pour les réglages. MISE EN GARDE : si vous vous sentez incapable d’installer l’appareil vous- ! même, confiez la tâche à un technicien qualifié. MISE EN GARDE : avant d'entamer l'installati
Resumo do conteúdo contido na página número 18
Installation CBLAGE DU SYSTÈME MISE EN GARDE : si vous ne vous sentez pas à l’aise pour effectuer vous- ! même le câblage de votre nouvel appareil, veuillez confier l’installation à votre concessionnaire Lightning Audio agréé. MISE EN GARDE : avant d'entamer l'installation, déconnectez la broche négative ! (-) de la batterie pour éviter tout risque de blessures, d’incendie ou de dommages à l'appareil. MISE EN GARDE : évitez de faire passer les fils d’alimentation près des câbles ! d’entrée de si
Resumo do conteúdo contido na página número 19
Installation AMPLIFICATEURS MONO X1.1000.1D et X1.2000.1D Ces amplis ont deux (2) sorties de haut-parleur pour plus de commodité et sont en parallèle à l'intérieur. MISE EN GARDE : les amplificateurs X1.1000.1D et X1.2000.1D ne sont pas ! recommandés pour des charges d'impédance inférieures à 1Ω . X1.400.2 X1.1000.1D X1.800.4 X1.2000.1D 19
Resumo do conteúdo contido na página número 20
Installation Source audio From Source Unit F Sour rom Sour ce audio ce Unit Amplificateur Amplificateur X1.1000.1D X1.2000.1D Source audio Source audio From Source Unit From Source Unit Amplificateur Amplificateur X1.400.2 2 canaux - pontés 2 canaux Source audio Source audio From Source Unit From Source Unit X1.800.4 4 canaux – Réglage en 3 canaux pontés 4 canaux TÉLÉCOMMANDE DE Attache de NIVEAU/ÉGALISATEUR DE BASSES fixation (modèles X1.1000.1D et X1.2000.1D seulement) Montage et installation
