Resumo do conteúdo contido na página número 1
User’s Manual
Model
SW10 ll SW12
Powered Subwoofer
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Resumo do conteúdo contido na página número 3
Thank you for your purchase of the NHT is to remember that low frequencies produce sounds with SW10 ll or SW12 powered subwoofer. long wavelengths, which interact in complex ways with room boundaries, such a walls and corners, and other Like all NHT loudspeakers, the SW10 ll and SW12's large objects as well. development has been guided by the study of human hearing, it’s design rigorously tested, and its components Placing the subwoofer near to a room boundary will tend optimized to deliver cl
Resumo do conteúdo contido na página número 4
is uneven. Some frequencies will sound exaggerated Two tips on using the Low Pass Filter: relative to others, or the subwoofer will sound thin and As a starting point, set Low Pass Filter to the 1 o’clock lack impact. The Boundary EQ control allows you to position. This will result in an 80Hz low pass. As the set- compensate for the effects of room boundaries on the ting is typical for most Dolby Digital / DTS applications. frequency response Note: The LFE input bypasses the adjustable 12dB L
Resumo do conteúdo contido na página número 5
9 8 7 4 Connecting The SW10II OR SW12 3 Line Input LFE Low Pass Filter Volume In L Caution: Before connecting the SW10II OR SW12 to Out R 40Hz 180Hz Min Max your audio system, it is important to unplug or turn off Power Hi Level Input Boundary 5 Mode Phase +3dB On 180 0 all AC power connections to connected components Auto 0 -3dB +L--R + such as receivers, amplifiers, preamplifiers, and proces- 6 sors. Do not plug in or connect the SW10II OR SW12 1 subwoofer to AC power until all connections
Resumo do conteúdo contido na página número 6
• Preamps with Line Out jacks: connect one pair of Line component's speaker output terminals to the L & R Out cables to your main amp to power your main L & R speakers, and a second pair from the same output ter- speakers, and a second pair to the SW10II OR SW12 minals to the SW10II OR SW12's High-Level input. The LINE LEVEL INPUT. If your preamp has only one pair of SW10II OR SW12's input does not present a significant Line Out jacks, you can use a pair of "Y" connector load to the receiver, a
Resumo do conteúdo contido na página número 7
The frequency chart below lists some terms commonly Fine Tuning the Subwoofer used to describe different bands of the frequency spectrum. Listen to your system and make adjustments The key to good subwoofer / speaker integration is to achieve a seamless blend between your main repeated listening, followed by making small re-adjust- speakers and the SW10 ll or SW12. Four common prob- ments of the subwoofer controls. The most important lems are outlined below. Follow the flow chart to correct ba
Resumo do conteúdo contido na página número 8
appropriate type. Operation • reinstall the fuse holder We recommend that the SW10 ll or SW12 power be left Always replace the fuse with one of the exact same on, which will allow the built-in Auto Mode feature to dis- specifications. able the subwoofer when not in use. Every speaker, has limits, and it's important to listen for SW10 ll: them. Speaker damage most often results not from brief loud musical peaks, but from sustained high volume lev- For systems operating at 115 volts, use only a
Resumo do conteúdo contido na página número 9
the back of a receiver, integrated amplifier or power Glossary amplifier. Active: Uses electrical power. Midrange: The frequency span in the middle of the audio Amplifier: An electronic device that increases the cur- range, roughly 180Hz - 3000Hz. Also used to describe rent and/or voltage of a signal, providing power to the the driver that reproduces these frequencies. loudspeakers (i.e. power amplifier, integrated amplifier, Ohm: A unit of electrical resistance. That which opposes receiver). a
Resumo do conteúdo contido na página número 10
Specifications All Super Series products are sonically matched for seamless integration into multichannel systems. Super Series SB1 SB2 SB3 ST4 SC1 SC2 SW10 SW12 Vented / Vented / System Type 2-Way Acoustic 2-Way Acoustic 2-Way Acoustic 3-Way Acoustic 2-Way Acoustic 2-Way Acoustic Powered - 150 watts Powered - 250 watts Suspension Suspension Suspension Suspension Suspension Suspension Class G Amplifier Class G Amplifier Driver Complement Tweeter- 1” fluid cooled aluminum dome tweeter with neodym
