Resumo do conteúdo contido na página número 1
Dell™ PowerEdge™
R715 Systems
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Dell™ PowerEdge™ R715 Systems Getting Started With Your System Regulatory Model E05S
Resumo do conteúdo contido na página número 4
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates potential damage to hardware or loss of data if instructions are not followed. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. ____________________ Information in this document is subject to change without notice. © 2010 Dell Inc. All rights reserved. Reproduction of these materials in any manner w
Resumo do conteúdo contido na página número 5
Installation and Configuration WARNING: Before performing the following procedure, review the safety instructions that came with the system. Unpacking the System Unpack your system and identify each item. Assemble the rails and install the system in the rack following the safety instructions and the rack installation instructions provided with your system. Getting Started With Your System 3
Resumo do conteúdo contido na página número 6
Optional — Connecting the Keyboard, Mouse, and Monitor Connect the keyboard, mouse, and monitor (optional). The connectors on the back of your system have icons indicating which cable to plug into each connector. Be sure to tighten the screws (if any) on the monitor's cable connector. Connecting the Power Cable(s) Connect the system’s power cable(s) to the system and, if a monitor is used, connect the monitor’s power cable to the monitor. 4 Getting Started With Your System
Resumo do conteúdo contido na página número 7
Securing the Power Cable(s) Bend the system power cable into a loop as shown in the illustration and secure the cable to the bracket using the provided strap. Plug the other end of the power cable into a grounded electrical outlet or a separate power source such as an uninterrupted power supply (UPS) or a power distribution unit (PDU). Turning On the System Press the power button on the system and the monitor. The power indicators should light. Getting Started With Your System 5
Resumo do conteúdo contido na página número 8
Installing the Optional Bezel Install the bezel (optional). Complete the Operating System Setup If you purchased a preinstalled operating system, see the operating system documentation that ships with your system. To install an operating system for the first time, see the installation and configuration documentation for your operating system. Be sure the operating system is installed before installing hardware or software not purchased with the system. Supported Operating Systems ® ® Micro
Resumo do conteúdo contido na página número 9
Microsoft Windows HPC Server 2008 R2 (x64) Edition Microsoft Windows Server 2003 R2 Standard and Enterprise (x64) Editions Microsoft Windows Server 2003 R2 Standard and Enterprise (x86) Editions Microsoft Windows Server 2003 R2 Standard, Enterprise, and Datacenter (x64) Editions Microsoft Hyper-V™ Server 2008 Microsoft Hyper-V Server 2008 R2 ® ® Red Hat Enterprise Linux 5.5 Server Standard and Advanced Platform (x86_32) Red Hat Enterprise Linux 5.5 Server Standard and Advance
Resumo do conteúdo contido na página número 10
Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document. The rack documentation included with your rack solution describes how to install your system into a rack. The Hardware Owner’s Manual provides information about system features and describes how to troubleshoot the system and install or replace system components. This document is available o
Resumo do conteúdo contido na página número 11
Technical Specifications Processor Processor type Two AMD Opteron™ 6000 Series processors Expansion Bus Bus type PCI Express Generation 2 Expansion slots Riser 1 Slot 1: x8 link with x16 physical connector, 9.5 inch length, standard height Slot 2: x4 link with x8 physical connector, low-profile with a standard height bracket System Board Slot 3: x8 link with x8 physical connector, low-profile Slot 4: x8 link with x8 physical connector, low-profile Riser 2 Slot 5: x8 link with x16 physical c
Resumo do conteúdo contido na página número 12
Drives Hard drives Up to six 2.5 inch, internal hot-swappable SAS, SATA, or SSD drives Diskette drive Optional external USB 1.44 MB Optical drive One optional slimline SATA DVD-ROM or DVD+RW drive NOTE: DVD devices are data only. Flash drive Optional internal dual SD module Optional vFlash card (with iDRAC6 Enterprise card) Connectors Back NIC Four RJ-45 (for integrated 1 GB NICs) NIC (management NIC) One optional management NIC port on iDRAC6 Enterprise card Serial 9-pin, DTE, 16550-compatib
Resumo do conteúdo contido na página número 13
Power AC power supply Wattage 750 W/1100 W NOTE: When two power supplies are installed, the system operates in power redundancy mode. Voltage 90–264 VAC, 47–63 Hz, auto-ranging Heat dissipation 2776 Btu/hr Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less Batteries System battery CR 2032 3.0-V lithium coin cell Physical Height 8.64 cm (3.40 inch) Width 48.24 cm (18.99 i
Resumo do conteúdo contido na página número 14
Environmental (continued) Relative humidity Operating 20% to 80% (noncondensing) with a maximum humidity gradation of 10% per hour Storage 5% to 95% (noncondensing) Maximum vibration Operating 0.26 G at 5–350 Hz for 15 min Storage 1.54 G at 10–250 Hz for 15 min Maximum shock Operating One shock pulse in the positive z axis (one pulse on each side of the system) of 31 G for 2.6 ms in the operational orientation Storage Six consecutively executed shock pulses in the positive and negative x, y,
Resumo do conteúdo contido na página número 15
Systèmes Dell™ PowerEdge™ Systèmes R715 Guide de mise en route Modèle réglementaire E05S
Resumo do conteúdo contido na página número 16
Remarques, précautions et avertissements REMARQUE : Une REMARQUE indique des informations importantes qui peuvent vous aider à mieux utiliser votre ordinateur. PRÉCAUTION : Une PRÉCAUTION vous avertit d'un risque de dommage matériel ou de perte de données en cas de non-respect des instructions données. AVERTISSEMENT : Un AVERTISSEMENT indique un risque d'endommagement du matériel, de blessures corporelles ou même de mort. ____________________ Les informations contenues dans ce document son
Resumo do conteúdo contido na página número 17
Installation et configuration AVERTISSEMENT : Avant d'exécuter la procédure ci-dessous, lisez les consignes de sécurité fournies avec le système. Déballage du système Sortez le système de son emballage et identifiez chaque élément. Assemblez les rails et installez le système dans le rack en suivant les consignes de sécurité et les instructions d'installation du rack fournies avec votre système. Guide de mise en route 15
Resumo do conteúdo contido na página número 18
Facultatif — Connexion du clavier, de la souris et du moniteur Connectez le clavier, la souris et le moniteur (si nécessaire). Aidez-vous des icônes des connecteurs situés à l'arrière du système pour savoir où insérer chaque câble. N'oubliez pas de serrer les vis situées sur le connecteur du câble du moniteur, s'il en est équipé. Branchement du ou des câbles d'alimentation Connectez le ou les câbles d'alimentation au système et, si vous utilisez un moniteur, connectez le câble d'alimentation
Resumo do conteúdo contido na página número 19
Fixation du ou des câbles d'alimentation Faites une boucle comme indiqué dans l'illustration, puis fixez-le à l'aide de la sangle fournie. Branchez ensuite l'autre extrémité du câble d'alimentation sur une prise secteur mise à la terre ou sur une source d'alimentation autonome (telle qu'un onduleur ou une unité de distribution de l'alimentation). Mise sous tension du système Appuyez sur le bouton d'alimentation du système et sur celui du moniteur. Les voyants d'alimentation s'allument. Guide
Resumo do conteúdo contido na página número 20
Installation du cadre en option Installez le cadre (en option). Finalisation de l'installation du système d'exploitation Si vous avez acheté un système d'exploitation préinstallé, consultez la documentation connexe fournie avec le système. Voir la documentation relative à l'installation et à la configuration du système d'exploitation si vous installez celui-ci pour la première fois. Veillez à installer le système d'exploitation avant tout élément matériel ou logiciel acheté séparément. Syst
