Resumo do conteúdo contido na página número 1
®
ED28/ED2820 and ED29/ED2920
“Harris Dome” Enclosures
Installation/Operation Manual
C460M-E (7/95)
PELCO • 3500 Pelco Way • Clovis, CA 93612-5699 • USA • www.pelco.com
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
PELCO Manual C460M-E (7/95) 33
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ...................................................................................................................................2 4.0 INSTALLATI
Resumo do conteúdo contido na página número 3
14.0 ENCLOSURE SPECIFICATIONS ....................................................................................................28 15.0 PAN/TILT ASSEMBLIES ...................................................................................................................29 15.1 ASSEMBLY DESCRIPTION .....................................................................................................29 16.0 ASSEMBLY SPECIFICATIONS .................................................................
Resumo do conteúdo contido na página número 4
REVISION HISTORY Manual # Date Comments C460M 3/89 Original Version. C460M 6/90 Revision A. Manual separated into two parts: enclosures and pan/tilt. Completely revised to include ED2820RX/PP and ED2820SL-RX/PP models. C460M 11/90 Revision B. Figure 2-4 revised. C460M 6/92 Revision C. Completely revised to include the following models: ED2820-3, ED220-PP, ED2820SL/PP, ED2820WX, ED2820SL-WX, and ED29/ED2920 Series. C460M-D 2/95 Revision D. Parts I and II integrated into one complete manual. Model
Resumo do conteúdo contido na página número 5
INSTALLATION/OPERATION MANUAL MODEL ED28, ED2820, ED29, ED2920 SERIES “HARRIS DOME” ENCLOSURES 1.0 WARNINGS Prior to installation and use of this product, the following 4. Only use replacement parts recommended by PELCO. WARNINGS should be observed. 5. After replacement/repair of this unit’s electrical com- 1. Installation and servicing should only be done by ponents, conduct a resistance measurement between Qualified Service Personnel and conform to all line and exposed parts to verify the exp
Resumo do conteúdo contido na página número 6
2.0 SCOPE combine concealed 360° surveillance with distortion- free viewing. The black opaque lower dome has a clear The information contained within this manual covers viewing slot which effectively camouflages a CCTV the Harris Environmental Dome. security/surveillance system without compromising the quality of the video picture. 3.0 DESCRIPTION The enclosure has been engineered for ease of installa- This product was developed outside of PELCO’s nor- tion, serviceability, and relocation. The
Resumo do conteúdo contido na página número 7
4.0 INSTALLATION ED2820-3SL/PP 4.1 UNPACKING INSTRUCTIONS ED2820SL/PP Twenty (20), plus ground for pan/tilt, lens and camera AC, plus two (2) for The dome and enclosure are shipped in separate cartons. heater/blower Make sure you have both before installing. Save the shipping cartons and plastic packaging in case any part ED2820-PP Nineteen (19) plus ground for pan/ of the unit has to be returned for credit or repair. tilt, lens and camera AC, plus two (2) for heater/blower 4.2 CONDUCTOR REQU
Resumo do conteúdo contido na página número 8
4.3 WIRING INSTRUCTIONS nating the need for wiring harnesses made in the field. Wire the control cable per Section 9.3 using the appli- Models ED28-1 and ED29-1 cable wiring diagrams in Figures 16 through 18, and supply the necessary power. These models are supplied with a factory installed heater/blower and service light. Supply 120 VAC Models ED2820-RX, ED2820SL-RX, power for the heater/blower and wire according to ED2820-RX/PP, ED2820SL-RX/PP, ED2920-RX and ED2920SL-RX Figures 3. When wirin
Resumo do conteúdo contido na página número 9
Figure 4. Heater/Blower Wiring Diagram (230 VAC) Wiring Pin Assignments Figure 3 Number Function Number Function Number Function 11 Not Used 21 Fan 1 Iris 12 Not Used 2 Zoom 22 Not Used 13 Heater #2 23 Not Used 3 Focus 14 Heater #2 4 Lens Common 24 Fan 15 Not Used 25 Not Used 5 Manual Iris 16 Heater #1 6 Not Used 26 Not Used 17 Heater #1 27 Not Used 7 Camera On 18 AC High 8 AC Input High 28 Connected to #6 19 AC Neutral 29 Not Used 9 AC Input Neutral 20 Ground 10 Ground 30 Camera Wiring Pin Ass
Resumo do conteúdo contido na página número 10
Figure 5. Receiver/Pan and Tilt Wiring Harness (Non-PP) 1 BROWN ALARM INPUT #1 2 RED ALARM INPUT #2 10 CONDUCTOR CABLE, 3 FEET 3 ORANGE ALARM INPUT #3 4 YELLOW ALARM INPUT #4 OPEN WIRES 5 GREEN ALARM INPUT #5 10 POS MTA CONN OUTSIDE DOME 6 BLUE ALARM INPUT #6 (CON1-640428-0) 7 VIOLET ALARM INPUT #7 8 GREY ALARM INPUT #8 9 WHITE ALARM OUTPUT CONA28S 10 BLACK ALARM COMMON WIRE AT 12 INCHES ZS-SPIROBAND 28 POS CONNECTOR 1 WHITE POS. COLOR DESC. 14 POS MTA PLUG 2 WHT/YEL (CON1-640428-4) 1 BROWN P/T
Resumo do conteúdo contido na página número 11
Figure 7. Coaxitron/Wiretron Power Patch (CX9024RX/WX8024RX) Wiring Schematic 4.4 INSTALLATION INSTRUCTIONS When the pan/tilt is removed, mount the camera/lens (see Figure 8) and make the electrical connections to the The Harris Dome is supplied in three (3) configurations: pan/tilt (camera power, video, lens). as a passive dome (for use as a dummy dome or with a fixed camera ), with a factory installed pan/tilt, or with When closing the dome, be sure the drive tab on the a factory installed p
Resumo do conteúdo contido na página número 12
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. Figure 8. Camera/Lens Mounting 4.4.1 Mounting the ED28/ED2820 Series 4.4.1.1 Wall Mounting The ED28/ED2820 series may be mounted directly to a wall or vertical surface. To attach the enclosure to a vertical surface, perform the following (see Figure 9): 1. Using the enclosure or the template supplied (see Figure 12), mark the location of the four (4) mount- ing holes. If the control and power cables are to pass through the
Resumo do conteúdo contido na página número 13
4.4.1.2 Corner Mounting The ED28/ED2820 series may be mounted to the out- side corner of a structure using the CM100 Corner Mount Adapter. To attach the enclosure to an outside corner, perform the following steps (see Figure 10): 1. Secure the CM100 corner mount adapter as stated in the installation manual provided with the mount. 2. Mount the enclosure to the CM100 using four (4) 1/4-inch diameter fasteners. 3. Route the power cord and control cables through the hole in the mount arm and make
Resumo do conteúdo contido na página número 14
ED28/ED2820 SERIES AND EDM210 HOLE PATTERN ST1 HOLE PATTERN Figure 11. Mounting Templates 10 PELCO Manual C460M-E (7/95)
Resumo do conteúdo contido na página número 15
4.4.1.3 EDM210 Mounting Extension 2. Drill the mounting holes according to the fasteners being used (minimum 5/16-inch diameter, not sup- When needed, the ED28/ED2820 series dome may be plied, quantity 4). mounted 10 inches (25.4 cm) farther from the mounting surface with the use of the EDM210 mounting exten- 3. Mount the enclosure to the EDM210 with the sion. It should be noted that in areas with heavy snowfall required fasteners. Route the cables through the or high winds, the ST1 support st
Resumo do conteúdo contido na página número 16
4.4.1.4 Parapet or Pole Mounting These mounts can be used in conjunction with the EDM210 mount extension and the ST1 strut. (See When mounting to a parapet, use of the PP200/PPI200 Figure 12.) parapet mount or PP300/PP301 parapet corner mounts is recommended. The ED28/ED2820 series dome may Follow the mounting instructions enclosed with the be mounted to other standard PELCO mounts, includ- appropriate mount and then proceed as stated in Section ing the PP100 Parapet Mount or the PA102 Pole Mou
Resumo do conteúdo contido na página número 17
4.4.2 Mounting the ED29/ED2920 Series 5.2 SERVICE TIPS The ED29/ED2920 Series domes require a suitable Some common problems encountered with pan/tilt sys- length of 1-1/2-inch NPT threaded pipe (not supplied) tems include miswiring, overloading, and not using the for mounting. The dome can be attached to any wall or units for the correct applications. If a failure occurs, it is ceiling capable of supporting the full weight of the recommended that the following procedures be used. mount, pan/ti
Resumo do conteúdo contido na página número 18
6.0 ED28 EXPLODED ASSEMBLY DIAGRAM Figure 14. ED28 Exploded Assembly Diagram 14 PELCO Manual C460M-E (7/95)
Resumo do conteúdo contido na página número 19
7.0 ED28 MECHANICAL PARTS LIST The following parts list corresponds to the exploded assembly diagram in Figure 14. Item Qty Description Part Number 1 2 Fastener ED210000 2 2 Receptacle ED210001 3 2 Retainer ED210002 4 1 Holder, Lamp (not shown) ED210020 5 1 Back Box Assy ED28001001WA 6 1 Plate, Front ED28004003COMP 7 1 Bracket, Cylinder ED28004011COMP 8 1 Bracket, Switch, Service Light ED28004031COMP 9 1 Dome, Clear 20" ED282006* 10 1 Cylinder gas spring, 20# EH550010020 11 6 NP Gasket, Poron E
Resumo do conteúdo contido na página número 20
8.0 INSTALLATION (Standard pan/tilt with presets) PT2801002ASSY: Pan/Tilt (9 plus ground) In order to ensure proper wiring and system operation of Lens (8) all components, it is highly recommended that the pan/ Camera AC (2) tilt and the associated control equipment be tested in your facility before field installation is attempted. As- (SL pan/tilt with presets) semble the mating connector as outlined in Figure 15 PT2801003ASSY: Pan/Tilt (10 plus ground) and wire the control cable according to
