Manual do usuário Pelco C1969M-A (1/02)

Resumo do conteúdo contido na página número 1

®
CCQ1400A-4
Color CCD Camera
with 4 mm Lens
Installation/
Operation Manual
C1969M-A (1/02)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120

Resumo do conteúdo contido na página número 2

IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P encolsure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4. When used with

Resumo do conteúdo contido na página número 3

DESCRIPTION OVERVIEW The CCQ1400A-4 color CCD camera with 4 mm lens is designed for use with the PMCQ14A 14-inch color quad monitor. A mini-DIN 6 connector in the back of the camera matches the connector on the back of the monitor. Power, alarm, audio and video contacts are all provided at this connector. MODELS CCQ1400A-KIT Camera assembly with audio, consisting of one CCQ1400A-4 camera, one WMQ8 bracket and one CCQCABLE-60 cable. CCQ1400A-4 1/4-inch color CCD camera with 4 mm lens, 12 VDC, wit

Resumo do conteúdo contido na página número 4

INSTALLING THE CAMERA 1. Assemble and mount the camera and bracket. CAMERA NOTE: The screws provided are intended for wood. If it is necessary to substitute screws for masonry or hollow wall mounting, be sure to use #6 or 4 mm hardware. BALL JOINT 2. Run cables. Refer to Installation Tips. THUMB NUT SET SCREW BRACKET MICROPHONE MIC MIC ALARM ALARM MONITOR MONITOR THUMB NUT SET SCREW BRACKET BASE IN GND IN GND 20103 20106 20105 3. Connect cable to camera. Insert plug with the arrow facing up. MIC

Resumo do conteúdo contido na página número 5

CHECKOUT Table A. Checkout Procedure When Adding a Camera to the System This procedure assumes that power is on and that the full monitor checkout has been performed. STEP PROCEDURE RESULTS 1 Calibrate camera. The CCQ1400A-4 camera is factory set for back focus. No further calibration is needed. 2 At the monitor, press the CH button for the channel See camera image full screen. the new camera is using. 3 Press the ZOOM/FREEZE button. Zoom area is highlighted in the center of the screen. Use arr

Resumo do conteúdo contido na página número 6

TECHNICAL SPECIFICATIONS ELECTRICAL Input Voltage: 12 VDC, +/-2 VDC Power Consumption: 2 watts Signal Format: NTSC Scanning System: 2:1 interlace Sync System: Internal Horizontal Resolution: 330 TV lines (center) Image Size Area: 4.57 mm (H) x 3.90 mm (V) Picture Elements: 512 (H) x 492 (V) Electronic Iris: 1/60 to 1/100,000 second Video Output: 1.0 Vp-p, +/-10%, 75 ohms Auto White Bal.: Electronic auto tracking Minimum Illumination: 0.9 lux at 30 IRE, f1.2 GENERAL Lens: C/CS Mount, F2.0, 4 mm l

Resumo do conteúdo contido na página número 7

Notice: Audio Monitoring on these Premises

Resumo do conteúdo contido na página número 8

REGULATORY NOTICES Note: This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communi