Resumo do conteúdo contido na página número 1
Model No. KV-S1025C
KV-S1020C
These instructions contain information on operating the scanner. Before reading these
instructions, please read the Installation Guide enclosed with this unit.
Keep the CD-ROM in the protective case. Do not expose the CD-ROM to direct sunlight or
extreme heat, and do not scratch or smudge the surface of the CD-ROM.
Resumo do conteúdo contido na página número 2
Thank you for purchasing a Panasonic High Speed Color Scanner. • Panasonic supports your imaging needs with a reliable and easy to use document scanner. • Panasonic has developed Panasonic Image Enhancement Technology to improve the quality of your scanned images even beyond the quality of your original document. Illegal Duplication It is unlawful to make duplication of certain documents. Duplicating certain documents may be illegal in your country. Penalties of fines and/or imprisonment may b
Resumo do conteúdo contido na página número 3
Table of Contents Page Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 For Your Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Component Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Setting up the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 • Setting and removing the feed tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 4
Notice Federal Communications Commission Requirements (For United States only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordan
Resumo do conteúdo contido na página número 5
For Your Safety To prevent severe injury and loss of life, read this section carefully before using the unit to ensure proper and safe operation of your unit. This section explains the graphic symbols used in this manual Denotes a potential hazard that could result in serious injury or death. WARNING Denotes hazards that could result in minor injury or damage to the unit. CAUTION These symbols are used to alert operators to a specific operating procedure that must not be performed. These sy
Resumo do conteúdo contido na página número 6
For Your Safety Never touch the plug or AC adaptor with wet hands. Danger of electric shock exists. Stop operation immediately if the unit emits smoke, excessive heat, abnormal smell, or unusual noise. These conditions can cause fire or electric shock. Immediately turn the unit off, and unplug the power cord, and contact your dealer for service. When disconnecting the unit, grasp the plug instead of the cord. Pulling on a cord forcibly can damage it, and cause fire or electric shock. Operatio
Resumo do conteúdo contido na página número 7
For Your Safety Installation Relocation Do not position the unit in a location where it is unstable. To prevent fire or shock hazard, do not expose this unit to rain or any type of moisture. Do not place the unit in a hot humid or dusty environment. Prolonged exposure to these adverse conditions may cause fire or electric shock. When moving the unit, be sure to unplug the power cord from the AC outlet. If the unit is moved with the power cord attached, it can cause damage to the cord which coul
Resumo do conteúdo contido na página número 8
For Your Safety Caution Labels CAUTION HOT SURFACE DO NOT TOUCH. The glass in the scanning section become very hot. Exercise care not to touch heated areas, or you may get burned. Precautions • Do not place the scanner in direct sunlight, in a cold draft, or near heating apparatus. • Do not place the scanner near apparatus which generate electronic or magnetic noise. • Protect the scanner from static electricity. • Do not move the scanner immediately from a cold place to a warm place. It may cau
Resumo do conteúdo contido na página número 9
Component Identification Document guides Feed tray extension Feed tray Door open button LED (Green) ADF door LED (Red) Security slot Exit tray Stand Start/Stop Exit tray extension button Scanning lamp(s) The scanning lamp(s) periodically lights up in sleep mode. This is not an unusual event. For details on sleep mode, refer to the User Utility Reference Manual. Door open button ADF door Open this door if a paper jam occurs. Mixed batch card guide Power connector Power switch USB port Connec
Resumo do conteúdo contido na página número 10
Setting up the Scanner Setting and removing the feed tray Before using the scanner, follow the steps below to set the feed tray. Adjust the document guides to the 1 width of A5 paper ( A ), and insert the A feed tray into the scanner ( ) as B shown in the illustration. B Push the right ( A ) and left ( ) B 2 sides of the feed tray in that order until A the feed tray locks in place. When removing the feed tray, lift it up to unlock, and then pull the left ( ) B and right ( A ) sides out o
Resumo do conteúdo contido na página número 11
Setting up the Scanner Setting the exit tray The exit tray prevents documents from dropping after they are scanned. Follow the steps below to set the exit tray. Note: • Documents can be fed through the scanner even if the exit tray is closed. Open the exit tray. 1 Exit tray Open the exit tray extension. 2 Exit tray extension Note: • The stand can be easily removed if so desired. For removing the stand, see page 37. Stand 11
Resumo do conteúdo contido na página número 12
Setting up the Scanner Power turn-on sequence Turn on the power of the scanner. 1 • Connect the power cord to the AC adaptor. • Connect the AC adaptor to the scanner. • Plug into an AC outlet. • Push the power switch. • The LED (Green) will blink for about 30 Power switch ( ) seconds and then it will become steady. Note: • Install the software first. Power cord USB cable AC adaptor About LED The status of the scanner can be established by the condition of the two LED indicators shown in the t
Resumo do conteúdo contido na página número 13
Installing Software System requirements ® ® Computer IBM PC/AT or compatible machine with a CD-ROM drive CPU Pentium lll, 1GHz or higher Interface USB 2.0 *1 *2 OS Windows 2000 , Windows XP Memory 256 MB or higher HDD At least 200 MB free space (except for data file) *1 ® ® Microsoft Windows 2000 operating system (hereafter Windows 2000) *2 ® ® Microsoft Windows XP operating system (hereafter Windows XP) CD-ROM Contents Contents Device Driver Drivers TWAIN ISIS RTIV Applications TM QuickScan P
Resumo do conteúdo contido na página número 14
Installing Software Complete installation All drivers, applications, utilities, and manuals can be installed at the same time using the Complete installation. Turn off the power of the scanner. 1 Insert the CD-ROM into your CD/DVD drive on your computer. 2 If you have a feature called ’Autorun’ activated, this will start the installation process 3 automatically. Note: • If the program does not automatically start, click [Start], click [Run...], click [Browse...], and select the CD/ DVD drive c
Resumo do conteúdo contido na página número 15
Installing Software Note: • If the program does not automatically start, click [Start], click [Run...], click [Browse...], and select the CD/ DVD drive containing the installation software, double-click on “CDRun.exe” in the root directory to manually start the installation routine, then click [OK]. Select your scanner. 4 Select the [All Drivers & Utilities] from the [Installation] list. 5 Follow the instructions on the screen. 6 Turn on the power of the scanner. 7 Follow the instructions of th
Resumo do conteúdo contido na página número 16
Installing Software Application installation RTIV and/or QuickScan Pro Demo can be installed as follows. Insert the CD-ROM into your CD/DVD drive on your computer. 1 If you have a feature called ’Autorun’ activated, this will start the installation process 2 automatically. Note: • If the program does not automatically start, click [Start], click [Run...], click [Browse...], and select the CD/ DVD drive containing the installation software, double-click on “CDRun.exe” in the root directory to
Resumo do conteúdo contido na página número 17
Installing Software Viewing manuals installed on your computer All manuals installed on your computer can be viewed as follows. Click [Start], and then click [All Programs] - [Panasonic] - [Scanner Manuals]. 1 • For Windows 2000, click [Program] instead of [All Programs]. Note: • To install manuals on your computer, see page 15. Select the desired manual. 2 17
Resumo do conteúdo contido na página número 18
Starting the Scanner Applications Automatically The scanner application can be configured to start automatically when pressing the Start/Stop button, and/or placing documents on the feed tray. To accomplish this, follow the steps below. Setting the event Click [Start], and then click [Control Panel] - [Printers and Other Hardware]. 1 • For Windows 2000, click [Start], and then click [Setting] - [Control Panel]. Select your scanner in the [Scanners and Cameras], and then display the scanner 2
Resumo do conteúdo contido na página número 19
Starting the Scanner Applications Automatically Select the check box of the desired scanner application(s) corresponding to the selected 5 event in the [Send to this application] list. • To disable the automatic activation of the scanner applications, set the [Disable device events] check box to on. Click [OK]. 6 Note: • When multiple applications are selected in the [Send to this application] list, the [Choose Application] dialog box will display, prompting you to select an application in th
Resumo do conteúdo contido na página número 20
Document Specifications Acceptable documents Document size: 2 48~216 mm (1.89~8.5 in.) Paper thickness: 40~209 g/m (11~55 lb.) The height of all the documents on the tray should be less than 5 mm (0.2 in.). This compares to 50 sheets (80 2 g/m or 20 lb.) of new paper. 70~2540 mm (2.76~100 in.) With the exception of ISO Magnetic Stripe cards, the minimum guaranteed feeding length is 70 mm (2.76 in.). Single paper feeding is recommended for papers exceeding the legal size length. Recommended
