Resumo do conteúdo contido na página número 1
[Sears !
owners
manual
MODEL NO.
113.298141
SAW ONLY
113.298031
SAW WITH LEGS
TWO TABLE EXTENSIONS
AND MOTOR
113.298151
SAW WITH LEGS
ONETABLEEXTENSION
AND MOTOR
Serial
Number.
Model and serial
number may be found
at the left-hand side
of the base.
You should record both
model and serial number
in a safe place for
future use.
IO-INCH TABLE SA IN
CAUTION:
• assembly
Read GENERAL
and ADDITIONAL
• operating
SAFETY
INSTRUCTIONS
• repair parts
carefully
Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60
Resumo do conteúdo contido na página número 2
3 FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW If within one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS STORE OR SERVICE CENTER THROUGHOUT THE UNITED STATES. This warranty givesyou specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., Sears Tower, BSC 41-3, Chicago, I
Resumo do conteúdo contido na página número 3
ADDITIONAL SAFETY INSTRUCTIONS FOR TABLE SAWS WARNING: FOR YOUR OWN SAFETY, DO NOT (sawing entirelv thru the work) AND by removmg OPERATE YOUR SAW UNTIL IT IS COMPLETELY a loose pieces from the table with a long stick of ASSEMBLED AND INSTALLED ACCORDING TO THE wood IMMEDIATELY after they are cut off. INSTRUCTIONS ... AND UNTIL YOU HAVE READ D. Use extra caution when the guaro assembly is AND UNDERSTOOD THE FOLLOWING. removea for resawing, dadoing, rabbeting, or 1. GENERAL SAFETY INSTRUCTIONS FO
Resumo do conteúdo contido na página número 4
R. DO NOT remove small ;)ieces of cut-off material efficiency when ripping, use the maximum diameter that may become trapped inside the blade guard blade for which the saw is designed, since under these while the saw is running. This could endanger your conditions the spreader is nearest the blade. hands or cause a kickback. Turn saw "OFF" and 15. AcIjust table inserts flush with the table top. NEVER wait until blade stops. operate the saw unlessthe proper insert is installed. S. Use extr_ care
Resumo do conteúdo contido na página número 5
Plug power cord into 110-120V properly grounded type GROUNDING LUG outlet protected by a 15-amp. time delay or Circuit-Saver fuse or circuit breaker, IF YOU ARE NOT SURE THAT YOUR OUTLET IS PROPERLY GROUNDED, HAVE IT CHECKED BY A QUALIFIED ELECTRICIAN. \ / 3-PRONG CONNECTED TO A WARNING: DO NOT PERMIT FINGERS TO TOUCH THE TERMINALS OF PLUG WHEN INSTALLING OR REMOVING THE PLUG TO OR FROM THE OUTLET. 2-PRONG RECEPTACLE WARNING: IF NOT PROPERLY GROUNDED THIS POWER TOOL CAN INCUR THE POTENTIAL HAZAR
Resumo do conteúdo contido na página número 6
UNPACKING AND CHECKING CONTENTS COMBINATION SQUARE MUST BE TRUE. TOOLSNEEDED STRAIGHT EDGE OF I_OARD 3/4 '1 THICK. THIS EDGE MUST BE PERFECTLY STRAIGHT. DRAW LIGHT LINE ON BOARD ALONG THIS EDGE. _'_\ Medium Screwdriver Small Screwdriver P, ie , , Wrenche I,I.:,:I',I.I_i, II'Z_ 3/8 in. 7/16 in. 1/2 in. 9116 in. SHOULD BE NO GAP OR OVERLAP HERE WHEN SQUARE IS FLIPPED Combination Square 3/4 in. OVER IN DOTTED POSITION. Model 113,298141 Table Saw is shipped complete in one LIST OF LOOSE PARTS carton
Resumo do conteúdo contido na página número 7
ItemPart Name Qty. Z Hex Nut, 5/16-18 A (approx. dia. of hole 5/16 in.) ........... 9 Z Hex Nut, 1t4-20 (approx.dia. of hole 114in.) ............ 2 AA Lockwasher,5/I 6 in. ExternalType (approx.die. of hole 5116in.) ........... 11 AA Lockwasher, 1/4 in. ExternalType (approx.alia.of h ale 1/4 in.) ............ 2 AA Lockwasher No. 10 ExternalType (approx.dia. of hole3t16 in.) ........... 1 © AB CarriageBolt, 5/16-18 x 3/4 in. long ....... 4 G H AC Rip FenceGuideBarSpacer .............. 2 AD Wire Ti
Resumo do conteúdo contido na página número 8
To remove insert. A) Loosen Screw B) Lift insert from front end, and pull toward front of saw, 4. To replace insert. Place insert into insert opening in table and push toward rear of saw to engage spring clip and until keyslot in insert will drop over screw. Tighten screw. Do not tighten screw to the point where it will deflect the insert. CHECKING BLADE SQUARENESS TO TABLE IMPORTANT: BLADE must be SQUARE (g0°) to TABLE, in order to proceed with assembly. To check for blade squareness, refer to
Resumo do conteúdo contido na página número 9
MOUNTING SAW 1. From among the loose parts, find the following hardware: 4 Hex Head Screws. 5/16 - 18 x 1-1/4 in. long. 4 Hex Nuts, 5/16- 18 (approx. dia. of hole 5/16 in.) 4 Lockwashers, 5/16 in. External Type (approx. dia. of hole, 5/16 in.) 8 Flat Washers, (dia. of hole 11/32 in.) 2. Place saw on legsso that holes in bottom of saw line up with holes in top of legs. 3. Install screws, washers, Iockwashers and nuts asshown. / / SAW BASE 17 END STIFFENER "_t FLAT WASHER---__ ' 13 LOCKWASHER "_'_
Resumo do conteúdo contido na página número 10
LayREARFENCE GUIDE BAR on table to act as a straightedge. If outer edge of extension is higher or lower than table surface; A. Slightly loosen nuts holding bracket to extension using 7/16 in. wrench. B. Move end of extension up or down until outer edge is even with table surface ... check with GUIDE BAR .., tighten nuts. C. Recheck INNER edge of extension to make sure it has not moved ... readjust, if necessary. INSTALLING RIP FENCE GUIDE BARS AND SWITCH BOX 1. From among the loose parts find th
Resumo do conteúdo contido na página número 11
9, Nold rod with one hand and with a 1/2 in. wrench or pliers start screwing on ONE of the nuts only A TURN OR TWO... screw on other nut the same way. 10. Using TWO 1/2 in. wrenches or pliers tighten both of the nuts. 1 I. Slide the bars so that screws are in the MIDDLE of the slotted holes. 12. Position rip fence over miter gauge groove, holding up the rear end while engaging front end with bar .., lower fence onto table. 8 THICKNESSES 13. Raise blade all the way up. OF PAPER 14. Carefully move
Resumo do conteúdo contido na página número 12
ALIGNING RIP FENCE The fence should slide easily along the bars and always remain in alignment (parallel to sawblade and miter gauge grooves). The alignment is maintained by a spring underneath the fence which bears against the front guide bar, To move the fence, loosen the lock handle and grasp the fence with one hand at the front. For very close adjustments, grasp the guide bar with both hands and move the fence with your thumbs. F Place fence on saw but DO NOT LOCK IT. Move the REAR END of th
Resumo do conteúdo contido na página número 13
If the fence does not slide easily along the bars, the pressure of the spring can be REDUCED. 1. Loosen the screws. 2. Move spring slightly toward rear of fence ... tighten screws. HEX SCREWS 3, The rip fence must be PARALLEL with the sawblade (seepage 29) and miter Gauge grooves... Move fence FENCE HEAD until it is along side of groove. Do NOT LOCK IT. It should be parallel to groove. If it is not; A. Loosen the two "Hex. Head Screws." B. Hold fence head tightly against bar ... move end of fenc
Resumo do conteúdo contido na página número 14
INSTALLING BLADE GUARD 1. From among the loose parts, find 2 Hex Head Screws, 1/4 - 20 x 5/8 in. long 2 Hex Head Screws, 5/16 - 18 x 5/8 in. long 2 Hex Head Screws, 5/16 - 18 x 1 in. long GUARD SUPPORT 2 Hex Nuts, 1/4 - 20 5/16-18 X (approx. dia. of hole 1/4 in.) 5/8 iN. 2 Lockwashers, 1/4 in, External Type HEX (approx. dia. of hole 1/4 in.) SCREW 2 Lockwashers, 5/16 in. External Type (approx, dia. of hole 5/16 in.} 1 Thumbscrew Guard Support CRADLE 5/16-18 X t IN. Spreader Support HEX HD. SCREW
Resumo do conteúdo contido na página número 15
9. Raise blade all the way up . .. make sure it is _quare with table. 10. Raise Blade Guard ... lift up both ANTIKICKBACK PAWLS ... insert one of the SETSCREW WRENCHES in the notches to hold the pawls out of the way, 11. Lay blade of square or other straightedge alongside of blade. 12. Loosen Hex Head Screw in GUARD SUPPORT and move spreader so that it touches blade of square ... tighten screw. 13. NOTE: The spreader s now square with the table and approximately in line with the sawblade. The sp
Resumo do conteúdo contido na página número 16
FOLDED PAPER 16.Place RIP FENCE on table ... CAREFULLY move it against blade so that it is parallel to the blade, and just TOUCHES tips of saw teeth ... tighten RIP FENCE LOCK KNOB HANDLE. 17. Insert folded paper between SPREADER and FENCE... hold spreader flat against fence.., tighten screws using 7/16 in. wrench, Now tighten Hex Hd. Screws in Support. 7/'16 IN. WRENCH 18. To remove BLADE GUARD AND SPREADER, loosen THUMBSCREW.,. DO NOT LOOSEN OTHER SC R EWS. MOUNTING THE MOTOR NOTE: Motor is in
Resumo do conteúdo contido na página número 17
11. Lift motor and insert the TWO PINS on motor base into HOLES in cradle ... push motor in asfar as it will go. 12. Lower the blade...install belt on saw pulley and motor pulley. 13. Sight along edges_ of both pulleys arid move motor pulley so that belt is parallel to the edges of both EDGE OF WASHER pulleys...tighten the setscrew in the motor pulley. EVEN WITH END 14. IMPORTANT: Measure the distance from end of motor OF SLOT shaft to pulley...mark this dimension down; you will need it later wh
Resumo do conteúdo contido na página número 18
TOGETHER _ _-_ TWO HOLES CLOSEST INSTALLING BELT GUARD BELT GUARD 10-32 X 1/2 IN. SUPPORT BRACKET SE L.F-THREADING 1. Remove the belt and motor pulley. SCREW \ 2. Screws furnished witli guard are "self threading" ... \ screw them into holes in BELT GUARD SUPPORT BELT GUARD SUPPORT BRACKET, then remove them. 3. Position BELT GUARD SUPPORT BRACKET and BELT GUARD SUPPORT as shown and install the BELT GUARD screws ... make sure motor shaft is in CENTER of hole in SUPPORT. \ PIVOT SCREW / / CENTERED
Resumo do conteúdo contido na página número 19
Press guard onto support so that bottom of guard is approximately 3/4 in. away from belt. NOTE: To remove guard, lift up on LONG TABS of cl ps ... pull guard outward. The clips should remain on the BELT GUARD SUPPORT. 1 3/_ IN. PLUGGING IN MOTOR 1. From among the loose parts, find two wire ties 2. Route motor cord along right side of cabinet and snap ties in 1/4" hole in side of cabinet. Secure two cords in w_re ties. 3. Plug motor cord into outlet on side of switch box. NIRE TIES 19
Resumo do conteúdo contido na página número 20
GETTING TO KNOW YOUR SAW _1 SAWSLADE 7" BLADE GUARD TABLEINSERT MITER GAUGE |0 EXACT-I-CUT ANTIKICKBACK \ PAWLS LOCK HANDLE 6 MITER GAUGE RiP FENCE RIP FENCE LOCK HANDLE 4 TILT LOCK HANDLE (UNDERNEATH TABLE) 2 ELEVATION HANDWHEEL \ 1 ON-OFF SWITCH 1 ON-OFF SWITCH CAUTION: Before turning switch on, make sure the blade guard is correctly installed and operating properly. The On-Off Switch has a locking feature. THIS FEATURE IS INTENDED TO PREVENT UNAUTHORIZED AND @ POSSIBLE HAZARDOUS USE BY CHILDR
