Resumo do conteúdo contido na página número 1
Straight Shear
MODEL JS1670
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPEC1 F I CAT IO N S
Mild steel Hard steel Stainless Aluminum Min cutting radius
1.0 mm 0.7 mm 0.7 mm 1.5 mm I 30 mm 306 mm 1.3 kg
(3164") 1 (1132") I (1132") I 11/16") (l-l/8'') I 4'500 I (12") I (2.9 Ibs)
* Manufacturer reserves the right to change specifications without notice.
Note: Specifications may differ from country to country.
Resumo do conteúdo contido na página número 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence of f
Resumo do conteúdo contido na página número 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltag
Resumo do conteúdo contido na página número 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Secure the workpi
Resumo do conteúdo contido na página número 5
Lubrication Before operation, lubricate the contact point of the center blade and the pin. To keep good cutting performance, also use a cutting lubricant from time to time during operation. Switch action To start the tool, move the slide switch forward, and the slide switch will lock in 1 Slide switch the "ON" position. To stop, lightly depress the rear of the slide switch, and it will re- turn to the "OFF" position. CAUTION : Before plugging in the tool, always check to see that t
Resumo do conteúdo contido na página número 6
MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps. Take out the
Resumo do conteúdo contido na página número 7
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Hex wrench 3 0 Wrench holder Part No. 410048-8 Part No. 783201-2
Resumo do conteúdo contido na página número 8
Apr -24-537 EN STRAIGHT SHEAR Model JS1670 Note: The switch, noise suppressor and other part configuratlons may differ from country to country. 8
Resumo do conteúdo contido na página número 9
July-17-'89 US MODEL JS1670 ""0" $2D DESCRIPTION $2D DESCRIPTION MACHINE MACHlNE ~ 1 4 Pan Head Screw M4x35 (With Washer1 30 1 SllP Plate L 2 1 Block 31 1 Space, Side Blade 3 1 Hex Lock NutM4-7 32 1 4 1 Set Screw M5x12 33 1 Hex Socket Head Bolt M5x10 5 1 Pan 7 34 1 Hex Socket Head Bolt M4x25 6 1 Stop Ring E-6 35 1 Hex Socket Head Bolt M5x10 36 1 Stop Ring E-4 7 1 Rubber Pin 4 8 1 Ball Bearing 627LLB 37 1 Teflon Washer 7 Thin Washer 7 9 1 Flat Washer 7 38 1 10 1 Rod 39 1 Center
Resumo do conteúdo contido na página número 10
MAKlTA LIMED ONE YEAR WARRANTY Warranty Policy Every Makita tool IS thoroughly inspected and tested before leaving the factory. It IS warranted to be free of defects from workmanship and materials for the penod of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year penod, return the COMPLETE tool, freight prepaid, lo one of Makita’s Factory or Authorized Service Centers. If inspectian shows the trouble is caused by defective workmanship or material,
