Manual do usuário Jet Tools Table

Resumo do conteúdo contido na página número 1

OWNER'S MANUAL
Tablesaw / Router Cabinet
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708308 05/01

Resumo do conteúdo contido na página número 2

This manual has been prepared for the owner of a JET XACTASAW™ Cabinet. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions in your tablesaw and/or Rout-R- Lift™ manuals before operating or servicing the machine. To obtain maximum life and efficiency from your cabinet, and to aid in using the tablesaw and/or Rout-R-Lift safely, read all manuals thoroughly

Resumo do conteúdo contido na página número 3

Unpacking Open shipping container and check that all parts are intact. Report any damage immediately to your distributor. Read the instruction manual thoroughly for assembly and alignment instructions. Box contents: 1 Back Panel 2 Side Panels 1 Bottom Panel 1 Top Panel 3 Angle Brackets 2SmallShelves 1 Large Shelf (used with closed stand saws) 4 Leg assemblies 1 Hardware bag 1 Door Handle 2 Hinges The contents of the hardware bag are drawn full scale in Figure 1. Installation Tools required • Phi

Resumo do conteúdo contido na página número 4

3. Attach a side panel in the position shown in Figure 4. The fasteners in the edge of the back panel will slide into the holes in the side panel. 4. Make sure the side panel is pushed all the way against the edge of the back panel, and push the fastener tabs all the way down. Repeat for the other side panel. 5. Mount the top panel, which has an opening. 6. Attach the bottom panel and make sure all fastener tabs are pushed down on the cabinet assembly. 7. Push the shaft of the leg into the base,

Resumo do conteúdo contido na página número 5

Installing the Cabinet to Extension Table 2. After the four 7/32” holes have been drilled mount the two angle brackets (A, Fig. 9) to the saw cabinet using four 1/4-20 x 5/8” hex 1. Cut the 3/4" x 2” runners to length. This washer head self tapping screws (B, Fig. 9). measurement may vary depending on the extension table. Measure from the end rail to the mid rail and cut to length, (Fig. 7). 2. Measure from the outer edge of the extension table’s side rails to 6-3/4” on the mid and end rails. Th

Resumo do conteúdo contido na página número 6

mount the angle bracket (A, Fig. 10) to the pre-drilled holes in the cabinet using two 1/4-20 x 1-1/2” round head machine screws, two 1/4" flat washers, two 1/4” lock washers and two 1/4” hex nuts, (B, Fig. 10). 3. Mount the shelf to the three brackets with three 1/4-20 x 1-1/2” round head machine screws, three 1/4” flat washers, three 1/4” lock washers and three 1/4” hex nuts. The end with the cutout should be against the tablesaw cabinet facing down. Note: You may need to cut the length of the

Resumo do conteúdo contido na página número 7

Cabinet Breakdown Index Part No. No. Description Size Qty. 1..........3136054W ....................... Cabinet Door ................................................. .................................1 3..........3721016W ....................... Small Shelf .................................................... .................................2 4..........3721017W ....................... Large Shelf.................................................... .................................1 5..........3

Resumo do conteúdo contido na página número 8