Resumo do conteúdo contido na página número 1
Concrete Slotting Saw
93009
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
®
Copyright © 2005 by Harbor Freight Tools . All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without
the express written consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353
SKU 93009 For technical questions, please
Resumo do conteúdo contido na página número 2
Specifications Needle Bearing with Adjustable Cutting Width .3" to 1" (8 to 26 mm) Drive Construction: Spindle Lock Dimensions: Depth .4" to 1.18" (10 to 30 mm) Blade Adjustable Double Blade 5" Diameter Diamond Blade Size and Type: Configuration: Optional Single Blade use Segmented Type A" rbor Size:7: /8 OM perating Speed 8000 RP Power 120 Volts, 60 Hz Dr rive Type: Worm Gea Requirement: 10.5 Amps (rated), 1250 Watts OH verall Dimensions:1: 4-1/2"L x 7"W x 7-1/2" N. et Weight 9.80 Lbs Included
Resumo do conteúdo contido na página número 3
7. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 8. Do not abuse the Power Cord. Never use the Power Cord to carry the tool or pull the Plug from an outlet. Keep the Power Cord away from heat, oil, sharpedges, or moving parts. Replace damaged Power Cords immediately. Damaged Power Cords increase the risk of electric shock. 9. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. These
Resumo do conteúdo contido na página número 4
21. Check for misalignment or binding of moving parts, breakage of parts, and any other condi- tion that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 22. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Service 23. Tool service must be performed only by qualified repair personnel. S
Resumo do conteúdo contido na página número 5
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed b
Resumo do conteúdo contido na página número 6
EXTENSION CORDS 1. Grounded tools require a three wire extension cord. Double Insulated tools can use either a two or three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. (See Figure C.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 g
Resumo do conteúdo contido na página número 7
Unpacking When unpacking, check to make sure the following parts are included. Concrete Wall Chaser with Two Blades and Spacers Steel Chisel Point 8-1/2” Long Two Point Spanner Wrench Side Mount Auxiliary Handle 5mm Hex Key When unpacking, check to make sure that all listed accessories are included, and that the product is intact and undamaged. WARNING! People with pacemakers should consult their physician(s) before using this product. Opera- tion of electrical equipment in close proximity to
Resumo do conteúdo contido na página número 8
3. To remove the blades, hold down the Spindle Lock (89) and insert the spanner’s pins into the two holes on the Flange Nut (57) and remove it. 4. Remove, replace, or rearrange the blades and spacers as necessary. Important! All 6 Spacers (54 and 55) must be used at all times, otherwise the blade will not be held securely. Also, Spacer (55) has a step designed to hold Blade (56) securely, Blade (56) must be placed on this spacer’s step, if Blade (56) is used. 5. Determine the desired spacing bet
Resumo do conteúdo contido na página número 9
Connecting a Dust Extraction Hose NOTE: This tool is fitted with an outlet (73 - 76) for attaching to a dust collection system (not included). 1. Insert the hose from your dust collection system (not included) into Connection Cap (76) and turn the Connection Cap clockwise to form a compression seal on your hose. NOTE: This fitting works with standard sized 2-1/2” dust collection hoses. Your system may vary. CAUTION: It is highly recommended that you use some type of dust collection system, since
Resumo do conteúdo contido na página número 10
6. After work is completed, release the Power Switch (30) to turn OFF the machine. Unplug the power cord from the power source. 7. Allow the tool to cool down before cleaning it. 8. After the machine has cooled down, and is unplugged, clean it with a dry brush to remove cement dust and other debris. 9. Disconnect any Dust Extraction System you may be using. 10. Wind up the tool’s power cord, and put the tool away for safekeeping. Always store it in a dry area out of reach of children and unautho
Resumo do conteúdo contido na página número 11
Parts List Pn artDy escriptio Qt 'tPn arDy escriptio Qt 'tPn arDy escriptio Q't 1wS4 cre 3r2W1 ashe 6w3S2 cre 2xG1 ear Bo 3r3W1 ashe 6w4S1 cre 3gL1 ocking Rin 3w4S1 cre 6e5C1 onnect Plat 4rW1 ashe 3e5N1 eedl 6r6W1 ashe 5rD1 riving Gea 3g6L1 ocking Rin 6e7D1 ust Collection Pip 6gB1 earin 3r7D1 riven Gea 6r8W3 ashe 7rB1 earing Cove 3g8L1 ocking Rin 6r9W3 ashe 8wS2 cre 3g9B2 earin 7w0S3 cre 9eA1 rmatur 4l0O1 il Sea 7r1A1 dapte 1e 0I1 ntermediate Flang 4e1B1 earing End Plat 7l2S1 ea 1r 1S1 tato 4y2K
Resumo do conteúdo contido na página número 12
Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. (92) Spanner (not shown) (93) Side Mount Auxiliary Hand (not shown) REV 07f SKU 93009 For technical questions, please call 1-800-444-3353 Page 12
