Resumo do conteúdo contido na página número 1
Operating Manual
HDTV receiver
for satellite reception
UFS 902
Resumo do conteúdo contido na página número 2
FOREWORD/IMPORTANT INFORMATION Dear customer, this Operating Manual is intended to help you make the fullest use of the extensive range of functions offered by your new HDTV satellite receiver. We have tried to make the operating instructions as easy as possible to understand, and to keep them as concise as possible. To help you understand particular specialist terms that cannot be translated, we have added a short glossary at the end of the manual. The power switch is an environmentally frie
Resumo do conteúdo contido na página número 3
FOREWORD/IMPORTANT INFORMATION Do not switch the receiver off at the power switch directly from the operating mode! This can lead to loss of data and corruption of the software. The channels available on the satellites and transponders are subject to continual change. In such cases, it is necessary to re-adjust the channels as the factory preset programming corresponds to the situation on the date of manufacture. The information for these settings can be found on the Internet or in relevant
Resumo do conteúdo contido na página número 4
RECEIVER FEATURES/PRODUCT PACKAGE The UFS 902 HDTV receiver is suitable for the reception of digital satellite TV and radio channels. The receiver can be used to receive both high resolution and also conventional TV. The built-in Common Interface offers capacity for one CA module for pay TV channels. The receiver indicates the channel name on the 12-character alphanumeric display. The HDMI interface allows the receiver to be connected to a HDTV-capable TV set. In addition one YpbPr connection
Resumo do conteúdo contido na página número 5
CONTENTS FOREWORD/IMPORTANT INFORMATION .................................................................................. 2 RECEIVER FEATURES/PRODUCT PACKAGE ............................................................................ 4 CONTENTS ............................................................................................................................... 5 SAFETY INSTRUCTIONS - IMPORTANT INFORMATION ............................................................. 6 CONTROLS, DISPL
Resumo do conteúdo contido na página número 6
SAFETY INSTRUCTIONS - IMPORTANT INFORMATION GB Safety Instructions – Important Information This page contains important information about the operation, installation location and connection of the unit. Read these instructions carefully before starting to use the unit. Mains cable Make sure that the mains cable (power supply cable) is not damaged. Units with a damaged mains cable must be disconnected from the mains (disconnect mains connector) and repaired by a qualified engineer before setup. O
Resumo do conteúdo contido na página número 7
CONTROLS, DISPLAYS AND CONNECTIONS This section provides a brief description of all the controls, displays and connections. The button symbols presented here can also be found in the description of the operating steps. VIEW OF FRONT PANEL (FLAP FOLDED DOWN) VIEW OF REAR PANEL USB 2.0 5V... 500 mA max Front panel controls and displays Rear panel controls and displays 1. Common Interface for one CA module 1. On/Off switch (with mains disconnect) ) for pay TV cards * (behind the fl ap) 2. Mai
Resumo do conteúdo contido na página número 8
CONNECTION AND SETUP The following section is intended specifi cally for specialist dealers. You need not refer to this section unless you are carrying out the installation yourself. The “Connection Examples” section provides a sample confi guration. Do not connect the receiver to the power supply until all installation work has been properly carried out. Refer to the information in the “Safety Instructions” section. CONNECTING THE UNIT (SAT IF CONNECTIONS) Connect the Sat IF input on the receiv
Resumo do conteúdo contido na página número 9
CONNECTION AND SETUP TV CONNECTION Connect the satellite receiver (HDMI or alternatively TV Scart socket) and the TV set using a HDMI or Scart cable (see “Connection Example”). If your TV is stereo, you can receive the sound in stereo via the HDMI or Scart connection. For system reasons, the same video signals are to be found at the TV Scart socket as at the video cinch output. AUDIO CONNECTION If you want to play the sound on your hi-fi system, connect the audio cinch sockets to the input so
Resumo do conteúdo contido na página número 10
REMOTE CONTROL Sound on/off Stand-by ... Teletext Enter numbers for channels, timer etc. (yellow) Open channel options Open main menu, sound/subtitles selection leave the menu and return to the TV picture (blue) Media selection (red) Open favourites selection Open channel OSD channel information (green) 1x open display of 4:3 programmes, 2x open HDMI/YUV format Channel selection up/down Volume Confi rm entry open channel list Leave menu step by step Cursor button
Resumo do conteúdo contido na página número 11
REMOTE CONTROL REMOTE CONTROL RC 660 The RC 660 remote control supports up to four units which are supplied as standard with the RC 660. First switch off all other receivers at the power switch. 1. Set-up using menu On the UFS 902 the remote control code on the “Service Menu”, “Remote Control Code” menu is changed. Note: The remote control code can only be changed using the menu. Manual changes are not saved by the receiver. 2. Manual set-up (not possible on UFS 902) Switch on the relevant rece
Resumo do conteúdo contido na página número 12
FIRST INSTALLATION Before using your receiver for the fi rst time, read the “Safety Instructions” and “Connection and Setup” sections. The “Connection Examples” section provides a sample confi guration. Do not connect the receiver to the power supply until all installation work has been properly carried out. The guidance given in the “First Installation” section assumes that the receiver has been properly connected as per the “Safety Instructions” and “Connection and Set-Up” sections. First sw
Resumo do conteúdo contido na página número 13
FIRST INSTALLATION The following display appears: Use the buttons here to select the settings for your TV set. When doing this, refer to the operating instructions for your TV set! Video Output via Select here the connection on the receiver to which you have connected your television. Either SCART or HDMI/YUV TV aspect ratio HDMI/YUV Format Here you select the TV's picture format. Either Select here the video resolution that is to be used on your TV. Either - 4:3 or - 16:9 - 1080i (re
Resumo do conteúdo contido na página número 14
FIRST INSTALLATION The following display appears: System Select the setting here to match your reception system using the buttons. You have the following options: - DiSEqC™1.0 - One Cable - LNB only If your reception system supports DiSEqC™, in “System” select “DiSEqC™1.0” (is used for switch- over from one received satellite to another). If your reception system does not support DiSEqC™, select the setting “LNB only”. If your receiver is connected to a single-cable system, select “One Cable
Resumo do conteúdo contido na página número 15
FIRST INSTALLATION: DiSEqC™1.0 Number of Satellites Use the buttons to select how many satellites (max. 4) you would like to receive with your reception system. The following display appears (example): Use the buttons to select the fi rst satellite slot. Press to open the menu for the satellite settings. The following display appears (example): Satellite and Position Use the buttons to set the desired satellite (selection from 17 pre-programmed options). 15
Resumo do conteúdo contido na página número 16
FIRST INSTALLATION: DiSEqC™1.0 LNB Type Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “user-defi ned”. Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. user-defi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was confi gured. Use the buttons to select the frequency range to be changed (low, high or limit frequency). Use
Resumo do conteúdo contido na página número 17
FIRST INSTALLATION: LNB ONLY Satellite and Position Use the buttons to select the desired satellite whose signal is to be received by the tuner. When you have selected your desired satellite, use the buttons to switch to the selection of the “LNB Type”. LNB Type Here use the buttons to select the LNB type used in your system. The choice is between “Universal” and “user-defi ned”. Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB.
Resumo do conteúdo contido na página número 18
FIRST INSTALLATION: LNB ONLY user-defi ned: If you choose not to use a universal LNB, you must here set the frequency ranges for which your LNB was confi gured. Use the buttons to select the frequency range to be changed (low, high or limit frequency). Use the buttons or the number buttons to set the exact frequency for which your LNB was confi gured. Test transponder To check whether the settings that you have made are correct, use the buttons to move to the “Test transponder” fi eld. Use
Resumo do conteúdo contido na página número 19
FIRST INSTALLATION: One Cable Use the buttons here to select “One Cable” as the “System”. Press the button to move to the next menu item. The following display appears: The various options for a single-cable system with Kathrein components are summarised at the end of this manual in the “Technical Appendix” section under “Examples of Single-Cable Systems”. Number of Satellites Use the buttons to select how many satellites (max. 2) you would like to receive with your reception syst
Resumo do conteúdo contido na página número 20
FIRST INSTALLATION: One Cable Universal: No further input is required, since all necessary frequency ranges are covered by a universal LNB. Wideband: No further input is necessary, since all frequency ranges are set by the Wideband LNB. user-defi ned: If you are not using a Universal or a Wideband system, you must set the frequencies here. You can fi nd the necessary information in the documentation supplied with your system. Use the buttons to select the frequency range to be changed (low, high
