Resumo do conteúdo contido na página número 1
Owner’s Manual
MEDIAMASTER
9902 S
Resumo do conteúdo contido na página número 2
SE NO Nokia intygar härmed att denna digitala mottagare, Nokia erklærer herved at denne digitale mottakeren, Mediamaster 9902 S, uppfyller kraven enligt direktiv Mediamaster 9902 S, er i overenstemmelse med 1999/5/EC. vesentlige krav og andre relevante bestemmelser i Denna mottagare kan anslutas till ett analogt EU-direktivet 1999/5/EC. telefonnät (Public Switched Telephone Networks , Dette terminalutstyret er beregnet på tilkobling til Det PSTN), under förutsättning att uppkoppling sker enligt
Resumo do conteúdo contido na página número 3
MEDIAMASTER 9902 S Contents Locked functions during recording 29 General Information 4 The Pause Recording 30-31 For your safety 4 The Normal recording 32 Service information 4 Timer recording 32 Remote control 5 To start playback of a recording 33 Front and rear panel 6 The pause function 33 Viaccess smartcard 7 Watch the playback at a different speed 34 CA module with its smartcard 7 Small steps during playback 35 Preparing the remote control 8 Find a specific position within a playback 35 Co
Resumo do conteúdo contido na página número 4
GENERAL INFORMATION ABOUT THE MEDIAMASTER Throughout this manual you will notice that the everyday operation of your Mediamaster is based on a series of user friendly on-screen displays and menus. These menus will help you get the most from your Mediamaster, guiding you through instal- lation, channel selection, viewing and many other functions. All functions can be carried out using the buttons on the remote control, and some of the functions can also be carried out using the buttons on the fro
Resumo do conteúdo contido na página número 5
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. Switch the Mediamaster in and out of standby mode. EXIT TV Return to the viewing mode from a menu without storing any settings (in menu mode). Switch between TV or Radio mode (in viewing mode). Turn the sound off/on (mute). - + Adjust the volume of digital programmes. The Mediamaster’s maximum level is
Resumo do conteúdo contido na página número 6
FRONT AND REAR PANEL Front panel Button Display Push the button to shows channel number, error messages, release an inserted remote control commands and time in CA module standby mode Slot Slot to put the Mediamaster for a Viaccess to move up/down in for a CA module in and out of standby the menus and to Smartcard with a Smartcard mode change channels. Rear panel DIGITAL AUDIO AUX SCART TELEPHONE * TV/VCR ANTENNA * * phono connector for connection to a VCR, for connection for an RF-cable to th
Resumo do conteúdo contido na página número 7
ABOUT THE SMARTCARD AND CA MODULE To be able to receive scrambled digital satellite channels you will need a Smartcard and/or a Common Interface CA (Conditional Access) module* from the Service Provider of your choice. The Service Provider is the programme distributor. If you are subscribing to services from more than one Service Provider, you might have to change between different Smart- cards and/or CA modules. Please note that a Smartcard and CA module may only be valid for a single Service P
Resumo do conteúdo contido na página número 8
INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: • the Mediamaster • remote control with 2 AAA batteries • SCART cable (fully featured 1,0 metre) • aerial/RF cable (double screened 1,5 metres) SCART cable RF cable • owner’s manual and software license agreement Remote Owner’s manual, control License agreement About the SCART sockets The rear panel of the Mediamaster is equipped with 2 SCART sockets (see diagram). When you connect other products to
Resumo do conteúdo contido na página número 9
INSTALLATION OF THE MEDIAMASTER General There are many different types of TV/VCR and other equipment that you can connect to the Mediamaster. In this manual you will see some of the most common ways to connect your equipment. If you use RF cables you will have to tune your TV and VCR to the Mediamaster output channel (see page 11). If you have problems with your connections and need help, con- tact your dealer or Service Provider. Connecting to the TV • Connect the SCART cable between the main S
Resumo do conteúdo contido na página número 10
INSTALLATION OF THE MEDIAMASTER Connecting an analogue satellite receiver and a VCR With Nokia smart • Connect a SCART cable between the main SCART socket on switch the TV and the TV SCART socket on the Mediamaster. • Connect a SCART cable between the VCR and the AUX SCART socket on the Mediamaster. VCR • Connect an RF cable from the RF output on the SCART VCR to the TV aerial input on the TV. RF • Connect an RF cable from the RF output on the analogue receiver to the RF input socket on the VCR.
Resumo do conteúdo contido na página número 11
INSTALLATION OF THE MEDIAMASTER Switching on for the first time with SCART connections • Plug in your Mediamaster • Now you will see the ”Welcome” menu on the screen. • Press OK on the Mediamaster remote control to start the In- stallation procedure. You may now proceed to “First time installation”, see next page. Tuning procedure when RF connections are used This procedure is necessary if your Mediamaster is con- nected to the TV with an RF cable, and not via SCART. To tune your TV to the RF si
Resumo do conteúdo contido na página número 12
FIRST TIME INSTALLATION General information Once you have correctly connected the Mediamaster, you also have to perform a “First Time Installation.” During this procedure, helpful information is displayed at the bot- tom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process. However, and this is important, often more than one value has to be entered in a menu. First, perform all necessar
Resumo do conteúdo contido na página número 13
FIRST TIME INSTALLATION RF modulator type If the Mediamaster is connected to the TV with a RF cable, you must select the right RF modulator alternative, which is depend- ent on the country where the Mediamaster is being used. Select “Normal (PAL B/G)” for all countries except the UK. Select “UK (PAL I)” when the box is used in the UK. If you get picture but no sound, the RF modulator selection might be wrong. Antenna/satellite selection Select one of the alternatives from line 1 to 4 if you have
Resumo do conteúdo contido na página número 14
FIRST TIME INSTALLATION Line through on the antenna satel- 1 4 lite selection menu Select one of the alternatives ASTRA, HOTBIRD, SIRIUS or THOR when you have a single LNB pointed towards any of these satel- lites. Pressing OK from the selected alternative will display the “An- tenna adjustment” menu (shown to the right) on the screen. For each satellite, (e.g. ASTRA, HOTBIRD, SIRIUS, THOR), up to 4 different channels are preprogrammed and shown in the menu. When you adjust the an
Resumo do conteúdo contido na página número 15
FIRST TIME INSTALLATION Line and on the antenna satellite 5 6 selection menu Select one of these alternatives when you have a single antenna equipped with 2 LNBs, or two antennas with one LNB on each, and want to watch channels from ASTRA/HOTBIRD or THOR/ SIRIUS. In this case you must first connect the LNBs to an external switch since there is only one antenna input on the Mediamaster. Once installed the switch automatically selects the correct LNB for the selected channel. TM This
Resumo do conteúdo contido na página número 16
FIRST TIME INSTALLATION Line 7 on the antenna satellite selection Menu This selection is necessary only when your satellite choice dif- fers from the preprogrammed satellite alternatives in the follow- ing ways; • if you do not use an universal LNB • when you have more than two LNB’s. • You also must select this alternative when your antenna is con- trolled by motor (ref. to page 19.) OK One antenna/one LNB configuration Select this alternative if you have one (1) LNB mounted on the antenna
Resumo do conteúdo contido na página número 17
FIRST TIME INSTALLATION For each LNB you connect to the DiSEqC switch, the fol- lowing configuration has to be performed. As an example the following part will describe how the LNB in- tended for Astra 1 will be configured to the DiSEqC input A on the switch and the LNB intended for Hotbird to DiSEqC input B. LNB type Select “Universal” or the local oscillator (L. O.) frequency valid for the connected LNB. LNB Offset voltage If the cable down from the antenna is very long, the voltage at the LNB
Resumo do conteúdo contido na página número 18
FIRST TIME INSTALLATION Multisatellite/four port DiSEqC Select this alternative if your antenna system has four LNBs and when you are not using any of the alternatives on the lines 5 - 6 from the menu “Antenna/satellite selection” on page 13. The selection of the different LNBs must be controlled by an external switch. Refer to page 15. The procedure is the same as for mini DiSEqC and two port DiSEqC, but you have to configure four LNBs the same way as described on page 16-17. Connection of a fo
Resumo do conteúdo contido na página número 19
FIRST TIME INSTALLATION Manual search When you perform a Manual search you first need to enter some parameters for the channel search to work. The information you need to enter in this menu is available in magazines covering satellite TV reception, on the Internet or from your Service Provider. Transponder frequency: Specify the frequency in GHz. If you enter the wrong figure(s), erase with the button. Polarization: Select Horizontal, Vertical, Circular left or Circular right. Symbol rate (MSym
Resumo do conteúdo contido na página número 20
FIRST TIME INSTALLATION Type of motor • Select SATSCAN if it is a Nokia SatScan motor. • Select DiSEqC in case the motor you use is controlled by DiSEqC commands. LNB type • Select Universal, one of the fixed frequencies or enter the LNB frequency with the numeric buttons on the remote control. LNB offset voltage If the cable down from the antenna is very long, the voltage at the LNB could be too low to change the polarization. You can in- crease the voltage to the LNB by 0,5 Volt. Satellite Sel
