Resumo do conteúdo contido na página número 1
INSTALLATION INSTRUCTIONS FOR PART 99-7426
APPLICATIONS
Nissan Murano 2009-10
(Without Bose Audio)
(Climate Controls must be above OE radio)
99-7426
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted Charcoal To Match OEM Finish
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
E) Double DIN Trim Plate • F) Pocket
F
B C E
D
Resumo do conteúdo contido na página número 2
99-7426 TABLE OF CONTENTS • Dash Disassembly - Nissan Murano 2009-10 ............................................1, 2 • Kit Assembly: - DIN Mount Radio Provision with Pocket ........................3 - ISO Mount Radio Provision with Pocket ........................4 - Double DIN Radio Provision ..........................................5 - Stacked ISO Mount Units Provision................................5 •Final Assembly ..............................................................6 *Note: Refer
Resumo do conteúdo contido na página número 3
99-7426 DASH DISASSEMBLY NISSAN MURANO 2009-10 1 Disconnect the negative battery termi- A nal to prevent an accidental short cir- cuit. 2 Unclip trim panel at bottom center of dash. (Figure A) 3 Remove (1) Phillips screw from bot- tom of each side trim panel. Unclip and remove the side trim panels. (Figure B) Remove (3) Phillips screws securing 4 the climate control then unclip, B unplug and remove it from the sub dash. (Figure C) Continued on next page. C 1
Resumo do conteúdo contido na página número 4
99-7426 DASH DISASSEMBLY NISSAN MURANO 2009-10 D 5 Remove (2) Phillips screws from the panel below the radio (containing the passenger air bag light) then unclip, unplug and remove the panel. (Figure D) 6 Remove (6) Phillips screws securing the radio to the sub dash. Unplug and remove radio. (Figure E) Continue to kit assembly. E 2
Resumo do conteúdo contido na página número 5
99-7426 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio hous- ing and secure by bending the metal locking tabs down. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 3
Resumo do conteúdo contido na página número 6
99-7426 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the ISO Brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the Trim plate onto the front of the Radio Housing. (Figure B) 4 Snap the pocket into the radio hous- ing. (Figure C) B Continue to final assembly. C 4
Resumo do conteúdo contido na página número 7
99-7426 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN or ISO mount unit(s) into the bracket/radio housing assembly and secure the unit(s) to the assembly using the screws supplied with the unit(s). (Figure C) B 4 Snap the
Resumo do conteúdo contido na página número 8
99-7426 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
