Resumo do conteúdo contido na página número 1
Owner’s Manual
Network Set-up and Operation
Wired Setting
Projector Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.
Resumo do conteúdo contido na página número 2
Compliance Federal Communications Commission Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu- nica
Resumo do conteúdo contido na página número 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ●W hen you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or otherac cidents. ● If you remotely use the projector via networks, carry out a safety check regularly and take particular care to its environment. Incorrect installation may cause fire or other accidents. CAUTION IN USING N
Resumo do conteúdo contido na página número 4
Table of contents Compliance ..........................................................................................................................................................................2 Federal Communications Commission Notice ....................................................................................2 Safety instructions ........................................................................................................................................................
Resumo do conteúdo contido na página número 5
Chapter 1 1 Preparation Describes features and operating environment of this projector. ENGLISH ENGLISH
Resumo do conteúdo contido na página número 6
Chapter 1 Preparation Features Web Management function ( +p.31) With this function, you can monitor projector functions PJ2 PC1 PC2 PJ1 such as power status, lamp s tatus, input mo de, signal condition, lamp-use time, etc. through the network by using PC3 PC4 PC6 the web browser installed on PC5 Turn ON PJ2 your computer. E-Mail Alert function ( +p.25) T h e p ro j e c to r s e n ds m e s- PC1 PC2 PJ2 PJ1 sages to the registered e-mail addresses when a lamp abnor- mality or power f
Resumo do conteúdo contido na página número 7
Computerenvironment Features Required operating environment for computers When operating the projector via networks, computers should meet the operating envi- ronment below. Windows 98, Windows Me, Windows NT4.0 Operating System Windows 2000, Windows XP, Windows Vista (32bit version) Mac OS X v 10.4 or later Windows: Higher than Pentium III 900MHz RecommendedCPU Macintosh : 8 00 MHz PowerPC G4 or faster,or 1.8 GHz Intel Core Processor or faster Windows : 64MB (Minimum)/ 128MB or more (Reco
Resumo do conteúdo contido na página número 8
Chapter 1 Preparation *1 The limitation of connection between the projector and hub or computer Suitable LAN cables are limited by length and type as follows; Connection Type of usable LAN cable Maximum length 2 Projector - Hub UTP Straight Cable with category 3 or 5 * 100m 2 Projector - Computer UTP Cross Cable with category 3 or 5* 100m *1 There may be other limitations depending on your network environment or LAN specification. Please consult your network administrator for further details
Resumo do conteúdo contido na página número 9
Flow of installation Flow of installation To use the projector via the networks, follow the setup procedures below. STEP 1 Connect the LAN and set the configuration. Decide depending on the LAN environment. ➔ “2. Setup Procedures” (pp .11–16). Detailed LAN configurations need to be done with a browser later. First, complete the Wired LAN connection between computers and projec- tors, then start browser configurations. ➔ “3. Basicsetting and oper ation” (pp.17–30). STEP 2 Network C
Resumo do conteúdo contido na página número 10
Chapter 1 Preparation 10
Resumo do conteúdo contido na página número 11
Chapter 2 2 Setup Procedures Describes how to configure the network. 11 ENGLISH ENGLISH
Resumo do conteúdo contido na página número 12
Chapter 2 Setup Procedures Setting procedures and contents differ depending on the LAN installation location. When installing, consult your system administrator to set up the LAN appropriately. Connecting to the LAN line Connect the LAN cable to the LAN connection terminal of the projector. LAN Connection ACT Lamp (Orange) Blink orange when the Terminal projector is sending or receiving the data. LINK Lamp (Green) Light green when the projector is connected to the network correctly. LAN Ca
Resumo do conteúdo contido na página número 13
Network configuration 3. Select "Network setting" in the Network menu and press SELECT button, and then the LAN setting screen will appear and selected LAN settings will be displayed. Adjust each item to the setting environment. Consult your system administrator about the detailed settings. Press SELECT button in a row where you want to adjust, and adjust the figures with the Point ed buttons and move among the items with the Point 7 8 buttons, and then press SELECT button to fix. Move to
Resumo do conteúdo contido na página número 14
Chapter 2 Setup Procedures Network PIN code The Network PIN code is to restrict the access from the networks to the projector. After setting the Network PIN code, you need to enter it to operate the projector via the networks. 1. Select "Network PIN code" in the Network menu, and press SELECT button. The Network PIN code screen will appear. 2. Set the Network PIN code. Set the figures with the Point ed buttons and move to the next items with the Point 7 8 buttons. Select “Set” and press SEL
Resumo do conteúdo contido na página número 15
Network factory default Network factory default 1. Select “Network factory default” in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. A ll the wired LAN settings will go back to the factory default settings. For details, refer to “Wired LAN factory default settings” (p.16). 15 ENGLISH
Resumo do conteúdo contido na página número 16
Chapter 2 Setup Procedures Wired LAN factory default settings SELECTED LAN Parameter LAN 1 LAN 2 LAN3 IP CONFIGURATION MANUAL DHCP MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAYADDRESS 255.255.255.255 255.255.255.255 255.255.255.255 DNS ADDRESS 255.255.255.255 255.255.255.255 255.255.255.255 1
Resumo do conteúdo contido na página número 17
Chapter 3 3 Basic Setting and Operation Describes basic operations and settings for controlling the projec- tor by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 17 ENGLISH ENGLISH
Resumo do conteúdo contido na página número 18
Chapter 3 Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser installed in your computer, enter the IP address into the "Address" on the browser and then press "Enter" key. Enter the address that you configured in item "Network configuration" ( + p.12). [2] Login If the setting page has set the password, the authentication window will appear. In this case type "user" onto the User Name text area and the login Network PIN code
Resumo do conteúdo contido na página número 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be displayed according to your display mode selection. Perform various kinds of settings through this page. Click on the menus to dis- play the control and setting pages. Main setting page in the display Sub menu tab Switches the sub menu tab. Setting page Main menu Displays the control and For selection of control and setting items according to setting items of the projector. t
Resumo do conteúdo contido na página número 20
Chapter 3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab. * Each item has a valid setting range respectively. Types of setting Text box setting Enter a number or text and then click Set button. or Change a value with – or + button. Pull-down menu