Resumo do conteúdo contido na página número 1
Resumo do conteúdo contido na página número 2
Copyright This publication, including all photographs, illustrations and software, is protected under international copy- right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2011 Disclaimer The information in this document is subject to change without notice. The manufacturer makes no repre- sentations or warranties with respect to the contents hereof and specifically discl
Resumo do conteúdo contido na página número 3
User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information. Note: Pro
Resumo do conteúdo contido na página número 4
Preface Projector Installation Notice Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically. Allow at least 50 cm (19.69 inch) clearance around the exhaust vent. (19.69 inch) (19.69 inch) (19.69 inch) (3.94 inch) (11.81 inch) (19.69 inch) Ensure that the intake vents do no
Resumo do conteúdo contido na página número 5
User’s Manual Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 39 for clear and safe instructions for this procedure. Before replacing the lamp: Unplug the power cord. Allow the lamp to cool for about one hour. Cleaning the Projector Unplug the power cord before cleaning. See Cleaning the Projector on page 42. Allow the lamp to cool for about one hour. Regulatory Warnings Before installing and using the projector
Resumo do conteúdo contido na página número 6
Preface Table of Contents GETTING STARTED........................................................................................................................................................... 1 PACKING CHECKLIST........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS.............................................................................................
Resumo do conteúdo contido na página número 7
User’s Manual AUDIO PROBLEMS ............................................................................................................................................................. 46 HAVING THE PROJECTOR SERVICED .................................................................................................................................. 46 HDMI Q & A ....................................................................................................................................
Resumo do conteúdo contido na página número 8
Safety Booklet IN5316HD/IN5318 – User’s Manual GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR REMOTE CONTROL CD-ROM (BATTERIES NOT INCLUDED) (THIS USER’S MANUAL) VGA CABLE POWER CORD REGISTRATION CARD (VARIES PER COUNTRY) SAFETY BOOKLET QUICK START GUIDE WARRANTY BOOKLET Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not w
Resumo do conteúdo contido na página número 9
User’s Manual Views of Projector Parts Front-angled View ITEM LABEL DESCRIPTION SEE PAGE: IR receiver Receives the IR signals from the remote control 1. 7 Lens Projection Lens 2. Focus ring Focuses the projected image 3. 17 4. Zoom ring Enlarges the projected image Elevator foot Adjusts level of projector 5. 14 See Top view—On-screen Display (OSD) but- Function keys 6. 3 tons. Lamp cover Remove cover to replace lamp 7. 39 Vertical lens shift Adjusts the image position ve
Resumo do conteúdo contido na página número 10
IN5316HD/IN5318 – User’s Manual Top view—On-screen Display (OSD) buttons ITEM LABEL DESCRIPTION SEE PAGE: MENU Open and exit OSD menus 1. Navigate and change settings in the OSD 2. ◄ (Left cursor) Quick Menu – For Volume Navigate the OSD ▲ (Up cursor) 3. Quick Menu – For Keystone 19 Navigate the OSD 4. ▼ (Down cursor) Quick Menu – For Keystone Navigate and change settings in the OSD ► (Right cursor) 5. Quick Menu – For Volume SELECT Enter or confirm highlighted
Resumo do conteúdo contido na página número 11
User’s Manual Rear view 1 2 3 4 7 89 10 11 5 6 12 13 14 15 16 17 19 20 22 24 25 26 18 21 23 ITEM LABEL DESCRIPTION SEE PAGE: DC 12V TRIGGER Connect a 12V screen trigger (200ma max) 1. AUDIO OUT Connect an AUDIO CABLE to an external speaker system 2. 3. AUDIO3 (L and R) Connect the AUDIO CABLE from an input device VIDEO Connect the COMPOSITE CABLE from a video device 4. S-VIDEO Connect the S-VIDEO CABLE from a video device 5. Connect the COMPONENT CABLE from a component video e
Resumo do conteúdo contido na página número 12
IN5316HD/IN5318 – User’s Manual Connect the USB CABLE from a computer USB 17. (used for presentation slide control with the projector remote) DISPLAYPORT Connect a DISPLAYPORT CABLE to a DISPLAYPORT source 18. HDMI Connect the HDMI CABLE from an HDMI device 19. 20. VGA2 Connect the RGB CABLE from a computer or a video enabled device RJ45 Connect a LAN CABLE for networking purposes 21. Solid Red Normal operation READY LED 22. Flashing Re
Resumo do conteúdo contido na página número 13
User’s Manual Bottom view ITEM LABEL DESCRIPTION SEE PAGE: Raise and rotate the feet to change and fine tune Leveling/Elevator Feet 1. 14 the angle of the projector. Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV). Ceiling support holes 2. See your InFocus dealer or go to www.infocusstore.com. Note: When installing, ensure that you use only UL Listed ceiling mounts. For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw d
Resumo do conteúdo contido na página número 14
IN5316HD/IN5318 – User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo- rescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path be- tween the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3. The buttons and keys on
Resumo do conteúdo contido na página número 15
User’s Manual ITEM LABEL DESCRIPTION SEE PAGE: Power ON Turn the projector on 1. 12 LED indicator Only lights when the remote keys are pressed 2. 3. Display Mode Choose a suitable preset mode for usage environment Contrast Display the Contrast setting bar and use the right and left keys to adjust 4. Display the Brightness setting bar and use the right and left keys to ad- Brightness 5. just. When the OSD is displayed, this button navigates to the Left cursor
Resumo do conteúdo contido na página número 16
IN5316HD/IN5318 – User’s Manual SETUP AND OPERATION Inserting the Remote Control Batteries Remove the battery compartment 1. cover by sliding the cover in the di- rection of the arrow. Insert the batteries (not included) as 2. shown in the illustration. Replace the cover. 3. Caution: 1. Only use AA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector f
Resumo do conteúdo contido na página número 17
User’s Manual Installing or Removing the Optional Lens Caution: Do not shake or place excessive pressure on the projector or the lens components as the projec- tor and lens components contain precision parts. Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans stop, and turn off the main power switch. Do not touch the lens surface when removing or installing the lens. Keep fingerprints, dust or oil off the lens surface. Do not scra
Resumo do conteúdo contido na página número 18
IN5316HD/IN5318 – User’s Manual Installing the New Lens Align the notches and correctly posi- 1. tion the electrical contact pad as shown in the picture. Note: Pin of IRIS should be in the direction as shown in the picture. Rotate the lens clockwise until you 2. feel it click into place. – 11 –
Resumo do conteúdo contido na página número 19
User’s Manual Starting and Shutting down the Projector Remove the lens cap. 1. Connect the power cord to the pro- 2. jector. Connect the other end to a wall outlet. Verify that the AC Power switch on the back of the unit is turned on. When connected, the PWR LED will turn solid Red. Turn on the lamp by pressing the 3. “ ” button on the rear of the projector or the Power On button on the remote. The PWR LED will now solid Green. The startup screen will display in approxima
Resumo do conteúdo contido na página número 20
IN5316HD/IN5318 – User’s Manual If more than one input device is connected, press the SOURCE button and use ▲▼ to 4. scroll among devices. • VGA 1 : Analog RGB • VGA 2 : Analog RGB • BNC : Analog / serial digital interface video inputs • HDMI : High Definition Multimedia Interface (HDMI) • DISPLAYPORT : DISPLAYPORT input • Component Video: DVD input YCbCr / YPbPr, or HDTV input YPbPr via HD15 connector • S-Video: Super video (Y/C separated) • Composite Video: Traditional composite
