Resumo do conteúdo contido na página número 1
English
®
Laser Printer WL-660 Series for Windows
Quick Setup Guide
First read this Quick Setup Guide to set up your printer and prepare your computer for the
printer.
CAUTION
This printer has been designed specially for Windows 3.1. It cannot work in a DOS
environment such as MS-DOS.
Action 1: Check the Supplied Items
After taking the printer out of the carton and removing the packing materials, make sure that
the following items are not damaged and none are missing:
• Printer • Multi-purpose s
Resumo do conteúdo contido na página número 2
English Action 2: Install the Toner Cartridge/Drum Unit 1 Unpack the drum unit and gently shake it from side to side five or six times. 2 Remove the protective parts, in order, as shown in the illustration. CAUTION Do not expose the drum unit to light for longer than a few minutes, as this will damage the drum. 3 Open the top cover. Open the drum cover by pushing the two blue tabs in toward the center of the unit and lifting the cover toward you. 4 Install the drum unit into the printer. Make su
Resumo do conteúdo contido na página número 3
English 5 Unpack the toner cartridge and gently rock it from side to side well before installing. ( ① ) Then, remove the protective parts. ( ② ) CAUTION DO NOT MOVE THE SHUTTER LEVER UNTIL THE CARTRIDGE IS INSTALLED. 6 Install the toner cartridge into the drum unit. Make sure that the ▲ marks are aligned. 7 Gently pull the blue shutter lever on the toner cartridge forward until the red arrows are aligned. 8 Close the drum cover ( ① ) and push gently until it clicks into place. Close the top cove
Resumo do conteúdo contido na página número 4
English Action 3: Load Paper into Your Printer 1 Install the paper support into the multi- purpose sheet feeder. ( ① ) Install the sheet feeder into the printer. ( ② ) 2 Open the multi-purpose sheet feeder cover. 3 Load paper into the multi-purpose sheet feeder. NOTE The feeder can hold up to 200 sheets of plain paper or up to 10 envelopes. Excessive sheets may cause paper jams. Make sure that the paper is stacked below the ▲ mark. 4 Move the paper guide to fit the paper width. 4
Resumo do conteúdo contido na página número 5
English 5 Close the multi-purpose sheet feeder cover. 6 Open the output tray. ( ① ) Extend the paper support wire. ( ② ) The printer can handle paper that has the following specifications: Paper Type Paper Size Paper Weight Sheet Manual Feeder Cut sheet A4, Letter, Legal, B5, A5, ●● 3”x5”, Executive, Custom size (70-216 x 127-356 mm 2.75”-8.5” x 5”-14”) 2 Envelopes DL, C5, COM-10, Monarch 60-135 g/m ●● ® Organizer Day-Timer J, K, L, M (16-36 lb.) ●● 70-216 x 127-356 mm 2.75”-8.5” x 5”-14” Label
Resumo do conteúdo contido na página número 6
English Action 4: Connect Your Printer and Computer You must connect the printer to your computer using an interface cable. A parallel cable is used for this connection. 1 Make sure that the power cord is unplugged before connecting or disconnecting the interface cable. Also, make sure that the computer is turned off. NOTE The shape of the power cord varies according to the country of destination. 2 Connect the parallel interface cable to the connector of the printer. ( ① ) Secure the connection
Resumo do conteúdo contido na página número 7
English Action 5: Plug in the Power Cord and Turn on Your Printer 1 Plug the power cord into the AC power outlet. NOTE This printer has no power switch. The printer has a sleep mode that allows the printer to automatically reduce power consumption when not in use. 2 Make sure that the READY lamp is ON after the printer has warmed up (about 60 seconds). 7
Resumo do conteúdo contido na página número 8
English Action 6: Set up the Printer Driver and Fonts for Windows 3.1 Check the following system requirements to run the Setup program and operate the printer correctly: • IBM PC or compatible with 80486 SX or higher microprocessor • Parallel interface (or printer port) • 4 MB or more of memory • 10 MB of space available on your hard disk for the printer driver and all fonts • Microsoft Windows 3.1/3.11 CAUTION This printer has been designed specially for Windows 3.1. It cannot work in a DOS en
Resumo do conteúdo contido na página número 9
English NOTE • The Setup program automatically updates Windows SYSTEM.INI file by adding DEVICE=bi-di.386 under the [386Enh] section. If any bi-directional parallel communications device driver has been previously installed, it will be deactivated by this new driver. If you want to use the previous driver, you should first install this driver, then re-install the previous one, which will make this driver inactive. • The Setup program makes the installed printer driver default. • The Setup progra
Resumo do conteúdo contido na página número 10
English Action 7: Set Print Options of Your Printer Before you print documents, set the print options of your printer as follows: 1. Make sure that Windows is restarted immediately after running the Setup program. 2. Open Control Panel in the Main group window. 3. Open Printers in the Control Panel window. 4. Make sure that your printer has been selected or made default. 5. Choose Setup to open the Setup dialog box of your printer. For more information about print options, choose Help or press t
Resumo do conteúdo contido na página número 11
English Action 8: Print Documents with Your Printer Now you can print documents from within your application software. Although print menus are somewhat different from application to application, you can print a document with the following basic steps: 1. Start your application software. 2. Type and save a document to be printed. 3. Choose Print from the File menu. If your software has Print Setup or equivalent under the File menu, you can choose print options from within the Print Setup dialog.
Resumo do conteúdo contido na página número 12
English Shipment of the Printer If for any reason you must ship your Printer, carefully package the Printer to avoid any damage during transit. It is recommended that you save and use the original packaging. The Printer should also be adequately insured with the carrier. Warning When shipping the Printer, the DRUM UNIT assembly including the TONER CARTRIDGE must be removed from the Printer and placed in Failure to remove and place it in the plastic bag the plastic bag. during shipping, will cau
