Resumo do conteúdo contido na página número 1
TEC Thermal Printer
TRST-56 SERIES
Owner’s Manual
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. ATTENTION Ce produit est de classe A. Dans un environnement domestique, il peut causer des interférences radio. Auquel cas, l’utilisateur sera amené à prendre les mesures adéquates.
Resumo do conteúdo contido na página número 4
Safety Summary EO1-13016 6DIHW\6XPPDU\ Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment. If a fault occurs that cannot be rectified using the procedures described in this manual,
Resumo do conteúdo contido na página número 5
Safety Summary EO1-13016 If foreign objects (metal When unplugging the power cords, ’LVFRQQHFW ’LVFRQQHFW fragments, water, liquids) enter be sure to hold and pull on the plug WKH SOXJ WKH SOXJ the machines, first turn off the portion. Pulling on the cord portion power switches and disconnect may cut or expose the internal wires the power cord plugs from the and cause fire or electric shock. outlet, and then contact your authorised TOSHIBA TEC representative for assistance.
Resumo do conteúdo contido na página número 6
EO1-13016 TABLE OF CONTENTS Page 1. PRODUCT OVERVIEW ---------------------------------------------------------------------------1- 1 1.1 Introduction---------------------------------------------------------------------------------------------------- 1- 1 1.2 Features-------------------------------------------------------------------------------------------------------- 1- 1 1.3 Applicable Model ------------------------------------------------------------------------------------------
Resumo do conteúdo contido na página número 7
1. PRODUCT OVERVIEW EO1-13016 1.1 Introduction 1. PRODUCT OVERVIEW 1.1 Introduction Thank you for purchasing the TOSHIBA TEC TRST-56 Series Thermal Printer. This printer is a compact line thermal printer designed to be connected to a TOSHIBA TEC POS terminal or used as a kitchen printer, etc. It prints an 80 mm-wide receipt at the maximum print speed of 150 mm/sec. The body colour is selectable between fair white (FW-2) and stylish grey (SG) so that it is possible to coordinate the co
Resumo do conteúdo contido na página número 8
1. PRODUCT OVERVIEW EO1-13016 1.4 Accessories 1.4 Accessories TEC Thermal Printer TRST-56 SERIES Owner's Manual TOSHIBA TEC CORPORATION Receipt Roll (1 pc.) Partition (1 pc.) Owner’s Manual (1 copy) NOTES: 1. The partition is provided for a case of using a 58 mm-wide receipt roll only. 2. The enclosed receipt roll is provided for an operation test. 1- 2
Resumo do conteúdo contido na página número 9
2. SPECIFICATIONS EO1-13016 2.1 Printer 2. SPECIFICATIONS 2.1 Printer Item Description Printing method Line thermal dot printing method Printing width 72 mm (576 dots) Resolution 8x8 dots/mm (203 dpi) Printing speed Max. 150 mm/sec. (1,200 dot lines/sec.) Printing columns Font A (12 x 24 dots): 48/42 columns Font B (9 x 24 dots): 64/56 columns Character size Font A: 1.25 x 3.00 mm Font B: 0.88 x 3.00 mm Character types Alpha-numerals, International characters, Code pages PC850, PC8
Resumo do conteúdo contido na página número 10
2. SPECIFICATIONS EO1-13016 2.2 Receipt Roll 2.2 Receipt Roll Width (W) Paper thickness (T) Inner core Outer core diameter (ID) diameter (OD) Outer diameter (D) Paper type Thermal paper rolled with the print side facing outside Width (W) 80 +0/-1 mm Outer diameter (D) 80 +0.5/-1 mm Paper thickness (T) 0.075±0.005 mm 2 Weight 69±3g/m Outer core diameter 18 mm Inner core diameter 12 mm Recommended thermal paper Only paper rolled onto a core is acceptable, however
Resumo do conteúdo contido na página número 11
3. APPEARANCE EO1-13016 3.1 Front/Rear View 3. APPEARANCE 3.1 Front/Rear View Front View Rear View Printer Cover Operation Panel Top Cover Power Switch Ejector AC Adapter Box AC Adapter Box 3.2 Operation Panel POWER LED (Green) POWER Lights when the power is turned on. ERROR LED (Red) ERROR The Error LED indicates an error by lighting or blinking. ON: Lights when an error is detected. OFF: No error is detected. (Normal state) FEED Button FE
Resumo do conteúdo contido na página número 12
3. APPEARANCE EO1-13016 3.3 Connectors 3.3 Connectors CAUTION! 1. The drawer interface connector is exclusively for connecting the drawer. Do not connect a phone line or any other cables than the drawer cable to this connector. Doing so may cause a failure of the phone line and this printer. 2. To the DC24V connector (socket connector), do not connect anything other than the built-in AC adapter. 3. The built-in AC adapter is exclusively for this printer. Do not use it for
Resumo do conteúdo contido na página número 13
4. SET UP PROCEDURE EO1-13016 4.1 Requirements for Operation 4. SET UP PROCEDURE 4.1 Requirements for Operation This printer has the following requirements: Serial interface Type • The TOSHIBA TEC POS terminal to be connected must have a serial port. • To communicate with the TOSHIBA TEC POS terminal, an RS-232C interface cable is required. RS-232C cable........ 25 pins Parallel Interface Type • The TOSHIBA TEC POS terminal to be connected must have a Centronics parallel port. • To c
Resumo do conteúdo contido na página número 14
4. SET UP PROCEDURE EO1-13016 4.2 Setting up the Printer 4.2 Setting up the Printer CAUTION! 1. Place the printer on a flat, stable surface. 2. Do not place the printer close to a heater or where it may be exposed to direct sunlight. 3. Avoid locations where the printer may be exposed to high temperature, high humidity or dust. 4. Care must be taken that no condensation occurs in the printer. If it should, however, do not turn ON the power until the condensation is dried.
Resumo do conteúdo contido na página número 15
5. INSTALLATION PROCEDURE EO1-13016 5.1 Connecting the Power Cord and Interface Cable 5. INSTALLATION PROCEDURE WARNING! 1. Since the power cord and the interface cable are not provided with this unit, please locally purchase ones which meet the specifications. For detail specifications, please contact your nearest authorised TOSHIBA TEC representative. 2. Before connecting the power cord and cables to the printer, turn the power of the POS terminal and printer OFF. 3. Do not p
Resumo do conteúdo contido na página número 16
5. INSTALLATION PROCEDURE EO1-13016 5.1 Connecting the Power Cord and Interface Cable 3) Connect and secure the interface cable to the interface connector in the correct orientation. Serial interface: Secure the connector with the screws. Parallel interface: Secure the connector with the locking tabs. Parallel Interface Connector Serial Interface Connector Locking Tab Serial Interface Cable Locking Tab Parallel Interface Cable [Serial Interface Type] [Par
Resumo do conteúdo contido na página número 17
5. INSTALLATION PROCEDURE EO1-13016 5.2 Connecting the Drawer 5.2 Connecting the Drawer CAUTION! The drawer interface connector is exclusively for connecting a drawer. Do not connect a phone line or any other cables than the specified drawer cable. Doing so may cause a failure of the phone line and the printer. 1) Turn the printer power OFF. 2) Connect the drawer cable to the drawer interface connector in the correct orientation. 3) Secure the ground wire of the drawer t
Resumo do conteúdo contido na página número 18
5. INSTALLATION PROCEDURE EO1-13016 5.4 Adjusting the Paper Near End Sensor Position 1) Turn the printer power ON. 2) Press down the ejector to unhook the printer cover. (c) 3) Hold both sides of the printer cover and open it until it stops.(d) 4) Check for the correct orientation of the receipt roll, and put it into the paper holder. 5) Pull the receipt until it extends past the paper outlet for about 5 cm (e), and then close the printer cover by pressing it’s front centre gently and m
Resumo do conteúdo contido na página número 19
5. INSTALLATION PROCEDURE EO1-13016 5.5 Self Test Print 5.5 Self Test Print When the power is turned on while pressing the [FEED] button, the printer will start a self test print. After completing the self test print, the printer will automatically cut the receipt and return to the stand- by mode. (while the printer is restored, the POWER LED goes off for a moment and soon lights again.) If the [FEED] button is kept pressed while the printer is restored, the self test print will be perfor
Resumo do conteúdo contido na página número 20
6. GENERAL MAINTENANCE EO1-13016 6.1 Cleaning 6. GENERAL MAINTENANCE WARNING! 1. Be sure to disconnect the power cord prior to performing any maintenance. 2. DO NOT POUR WATER directly onto the printer, as this may cause electric shock or fire. 3. The print head becomes very hot while printing. To avoid getting burned, never touch the print head during the maintenance. CAUTION! 1. Do not use any sharp object to clean the print head and platen. Doing so may damage them, ca
