Resumo do conteúdo contido na página número 1
DOT MATRIX PRINTER
DP8340 SERIES
[PARALLEL INTERFACE]
USERS MANUAL
Resumo do conteúdo contido na página número 2
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS 1. OUTLINE .............................................................................................. 1 2. UNPACKING AND INSTALLATION ................................................ 2 2-1. Unpacking .................................................................................... 2 2-2. Installation of Paper Holders and Re-Roll Prevention Guard (Only Model DP-8340FC) ........................................................... 3 2-3. Handling Notes.......................
Resumo do conteúdo contido na página número 4
Resumo do conteúdo contido na página número 5
1 . OUTLINE The DP8340 series of serial dot matrix printers is for use in ECR, POS, electronic instruments, banking machines and computer peripheral equipment. The DP8340 series include the following features; 1) 2 color printing (Red and Black) 2) High-speed bidirectional printing (2 line/sec, 40 columns per line) 3) 9-pin print head 4) Parallel interface (Centronics compatible) 5) Commands for expanded characters, inverted characters, emphasized char- acters, and red and black printing are p
Resumo do conteúdo contido na página número 6
2. UNP A CKING AND INST ALLA TION 2-1. Unpacking After opening the box, check if all necessary accessories are included. (A) Printer 1 Printer 4 Re-Roll Prevention Guard 2 User’s Manual 5 Ink Ribbon 3 Paper Holders 6 DIP Switch Cover (B) Power Supply Unit 1 1 Power Supply Unit 2 User’s Manual Figure 2-1. Unpacking – 2 –
Resumo do conteúdo contido na página número 7
2-2. Installation of Paper Holders and Re-Roll Prevention Guard (Only Model DP8340FC) Install the Paper Holders in the outermost holes in the rear of the printer. Figure 2-2. Installation of Paper Holders – 3 –
Resumo do conteúdo contido na página número 8
Install the Re-Roll Prevention Wire in the holes of the printer cover. Twisting the Wire as shown in the figure below, will make the installation easier. Figure 2-3. Installation of Re-Roll Prevention 2-3. Handling Notes (1) Install the printer near an easily accessible socket-outlet. (2) Place the unit on a flat and stable surface for operation. (3) Do not connect the AC Power Plug to the same outlet used for other noise generating devices (large motors, etc.). (4) Be careful not to drop paper
Resumo do conteúdo contido na página número 9
3. PAR T IDENTIFICA TION AND NOMENCLA TURE 3-1. Power Supply Unit DC Power Connector (Output) Shape of AC Power plug will vary according to destinations. Figure 3-1. Power Supply Unit – 5 –
Resumo do conteúdo contido na página número 10
3-2. Printer Figure 3-2. Printer: Front View Figure 3-3. Printer: Rear View – 6 –
Resumo do conteúdo contido na página número 11
3-3. Part Functional Description (1) AC Power Plug Connect to an outlet of the specified voltage. (2) DC Power Outlet Supplies DC 12V power to the printer. (3) Printer Cover Protects the printer against dust and reduces noise. (4) POWER Lamp Lights up (green LED) when power is on. (5) ON LINE Lamp Lights up (green LED) when the unit is in the online mode. (6) ALARM Lamp Lights up (red LED) when printer operation is not normal, or the printer is out of paper. It is necessary to install paper into
Resumo do conteúdo contido na página número 12
4. INST ALLA TION OF INK RIBBON AND PAPER 4-1. Installation of Ink Ribbon (1) Turn power off, lift the Printer Cover up and remove it. Note: Be careful not to touch the print head immediately after printing, because it can get very hot. Figure 4-1. Printer Cover Removal (2) Unwind ribbon so that the spools are separated as shown in Figure 4-3. Hold the ribbon taut as shown with the drive pins facing down and slide the ribbon between the print head and the platen. While keeping the ribbon t
Resumo do conteúdo contido na página número 13
Ribbon Life Ribbon life Description Black SF-03B Approx. (Fuji Kagakushi 0.8 million Kogyo Co., Ltd.) characters Figure 4-2. Installation of Ink Ribbon Figure 4-3. Ribbon Spools 4-2. Removal of Ink Ribbon Hold the spool and lift gently, rotating it until the ribbon sags. Push the ribbon detecting lever out, lift the spool until it comes off the shaft. Remove the second spool in a similar manner. (Do not apply excessive force when lifting spools.) – 9 –
Resumo do conteúdo contido na página número 14
4-3. Paper Insertion 4-3-1. Model DP8340FC (1) Cut the Roll Paper end straight and square. Hold the roll so that the paper comes from the bottom. (2) Attach the Roll Paper to the Holders Paper by slipping one side of the roll onto the Hub and pulling the other Hub out to allow the roll to slip in place. (3) Insert the paper evenly into the Paper Insertion Slot. (4) Turn the Power Switch “ON”, and press the FEED Button. The paper will be fed into the unit. Figure 4-4. Paper Insertion (1) [Model D
Resumo do conteúdo contido na página número 15
4-3-2. Model DP8340SC 1. Make a straight cut along the top of the paper, about 1/4 inch away from the sprocket holes, (as shown in the figure). If there is perforation, cut the paper on the perforation. 2. Insert the paper squarely into the paper insertion slot until the ALARM lamp goes out. Then, hold down the FEED switch to advance the paper 8 lines, and release the switch when 8-line feeding is completed. If the paper is not fed straight during 8-line feeding, straighten the paper by pulling
Resumo do conteúdo contido na página número 16
4-4. Paper Removal Cut the paper close to the slot and use the feed button until paper has passed completely through the printer. Note: Do not try to remove the paper by hand as it could become crooked and get jammed inside the printer. – 12 –
Resumo do conteúdo contido na página número 17
5 . CONTR OL CODES LF CODE (0A)H FUNCTION Print and line feed instruction OUTLINE The LF code causes the data in the line buffer to be printed, followed by a single line feed. When the line buffer is empty, only the feed takes place. CR CODE (0D)H Print and line feed instruction FUNCTION OUTLINE Same function as of LF code. However, when the DIP switch 3 is ON, the CR code becomes invalid. CODE SO (0E)H FUNCTION Expanded character instruction OUTLINE This code causes the printer to print expan
Resumo do conteúdo contido na página número 18
SI CODE (0F)H FUNCTION Inverted print instruction OUTLINE This function causes the printing to be inverted. This code must be received at the beginning of a line. If this code is received anywhere other than at the beginning of a line, it is disregarded. Accordingly, normal characters and inverted characters, can not be mixed on the same line. DC2 CODE (12)H FUNCTION Release from inverted print instruction OUTLINE The inverted print instruction is released by this code. This code must be receive
Resumo do conteúdo contido na página número 19
ESC R n CODE (1B)H (52)H n FUNCTION Select an international character. OUTLINE This command selects one of the international character sets in accordance with the value of “n” as shown below. n = 0 : U.S.A. 3 : England 6 : Italy 1 : France 4 : Denmark 7 : Spain 2 : Germany 5 : Sweden 8 : Japan International character set can be specified using the DIP Switches. However, control code settings have priority.For international characters, please refer to the character code chart in Section 8, or to
Resumo do conteúdo contido na página número 20
Relation Between Character Pattern Data and the Print Head ESC % 1 CODE (1B)H (25)H (01)H or (1B)H (25)H (31)H Select download character FUNCTION OUTLINE This code specifies the download mode. Download char- acters defined by the previously explained &0 code cannot be printed unless this code is first sent to the printer. ESC % 0 CODE (1B)H (25)H (00)H or (1B)H (25)H (30)H FUNCTION Cancel download character OUTLINE This code cancels the download mode and selects standard text charac
