Resumo do conteúdo contido na página número 1
UX-2200CMU/CMC
FO-2150CMU/CMC
TECHNICAL MANUAL
No. 00ZU220CMUTME
FACSIMILE
INK JET PRINTER
UX-2200CM
MODEL FO-2150CM
This Technical Manual contains detailed information about the printer for the UX- 2200CM / FO-2150CM
to the Service Manual already issued.
CONTENTS
[1] Engine Specifications ........................................................................................................................... 1
[2] Abbreviations .............................................................
Resumo do conteúdo contido na página número 2
UX-2200CMU/CMC FO-2150CMU/CMC [1] Engine Specifications 1. Mechanism Resolution : 600 dpi x 600 dpi addressability Print Speed : 3 PPM draft text with black cartridge Print Swath : 8 inches Duty Cycle : Up to 500 pages per month maximum, 170 pages per month average Dimensions (approximate) : 350mm x 125mm x 60mm Weight (approximate) : 1.2 pounds Acoustics : 45 dBA in letter quality mode (using Lexmark paper feed and covers which is not included) 2. Electrical No electrical hardware included wi
Resumo do conteúdo contido na página número 3
UX-2200CMU/CMC FO-2150CMU/CMC [4] Circuit description 1. General description The compact design of printer PWB is obtained by using 8 bit microprocessor(CPU) and ASIC in the printer control section. 2. Electrical System The PWB provides mechanical control for Ink Jet Printer. Figure 1 shows the interconnection of PWB and other electrical component in the print mechanism. Ink Cartridge CN3 CN4 CNPRT Host Interface CN2 PC1 CN1 Cartridge Carrier Motor Paper Feed Motor Figure 1 – 2 –
Resumo do conteúdo contido na página número 4
UX-2200CMU/CMC FO-2150CMU/CMC 3. Electricai Overview The information in this section appears in a sequence relative to the system diagram in the following figure. SRAM 8bit Head Driver MPU ASIC Driver Carriage Motor Host Interface TO FAX PWB Driver Feed Motor Sensor •Home Position •Paper-IN Figure 2 System of printer Block diagram 4. Power Supply Connector The mechanism requires two voltages (+5V and +24V). These two voltages supplied from CNPRT connector. 5. Host interface connector Connector C
Resumo do conteúdo contido na página número 5
UX-2200CMU/CMC FO-2150CMU/CMC 7. Driver IC The paper motor and carriage motor require current that cannot be driven directly from ASIC chip. Motor driver IC provide the additional current and voltage capability. The driver IC (IC1 and IC2) located near the respective motor connector on the printer PWB also connect back to the ASIC. Two additional drivers IC drive 56 nozzles on the cartridge. These driver ICs , located between the two flex-circuit connector (CN3 and CN4) on the printer PWB , also
Resumo do conteúdo contido na página número 6
UX-2200CMU/CMC FO-2150CMU/CMC (2) Print transfer The planetary gear turns clockwise and is disconnected from the PU gear,so that the paper is not fed automati cally. In case of hand paper feed the paper is fed directly to the transfer roller. HAND FEED PAPER PLANET GEAR MOTOR GEAR AUTOMATIC FEED PAPER PU GEAR When the mechanism stops, the automatic paper feed is not performed PRINTER FEED GEAR 9. Carriage Motor The ASIC controls the carriage motor, which is a stepping motor that connects via a
Resumo do conteúdo contido na página número 7
UX-2200CMU/CMC FO-2150CMU/CMC 12. Home Position Sensor LEFT RIGHT B C A CARRIAGE HOLDER The home position of carriage is detected as a result of change of output of photointurrupter A which is caused due to shutting-off of optical path of photointerrupter A by the slit B . While the photointerrupter is shut off by the slit B, the output (pin 1 of CN3) of photointerrupter gets H level (+5V). If it is not shut off, the output gets L level (0V). In the home position the output is L. In case
Resumo do conteúdo contido na página número 8
UX-2200CMU/CMC FO-2150CMU/CMC [5] Overall Trouble Shooting Of Printer PWB • BOTH CARRIAGE MOTOR AND FEED MOTOR ARE NG. REPLACE F100 AND F101 FUSE “F100” AND “F101 OPEN OK CHECK RESISTANCE CHECK +24V PATTERN +24V AT Q1-E (Figure 1) +24V AT Q1-C (Figure 1) BETWEEN +24V AND GND. NG NG NO SHORT OR NOT SHORT OK REPLACE PRINTER PWB CHECK IC5 AND IC8 AND +5V AT Q101-B (Figure 2) REPLACE IC5 OR IC8 R145,R144 NG NG OK OK OK REPLACE PRINTER PWB 0V AT Q101-C (Figure 2) REPLACE Q101 (Figure 2) NG OK REPLA
Resumo do conteúdo contido na página número 9
UX-2200CMU/CMC FO-2150CMU/CMC • FEED MOTOR IS NG (CARRIAGE MOTOR IS GOOD) Check the laser diode driver. FUSE “F101” REPLACE F101 OPEN OK CHECK WAVEFORMS IC2 ( 2,4,6,8 pin) (Figure 4) CHECK IC5 REPLACE IC5 NG NG OK OK REPLACE PRINTER PWB CHECK IC2 REPLACE IC2 CHECK WAVEFORMS IC2 ( 3,5,7,9 pin) (Figure 3) NG NG OK OK REPLACE PRINTER PWB REPLACE PRINTER PWB +40~50V IC2-2,4,6,8PIN INCLUDE OVERSHOOT 1.5V +24V GND GND Figure 4 Figure 3 • CARRIAGE MOTOR IS NG (FEED MOTOR IS OK). PLS INSERT THE CABL
Resumo do conteúdo contido na página número 10
UX-2200CMU/CMC FO-2150CMU/CMC • MISSING NOZZLES (RESULT OF CHECK PATTERN OR CLEAN NOZZLES CLEAN NOZZLES NG REPLACE ANOTHER CARTRIDGE NG CHECK IC AND CONNECTOR BY MISSING MANY NOZZLES REFERING TO THE TABLE 1&2 NO YES CHECK THE SOLDER IC4, IC6 COMMON pin IC 5 82-89 pin CORRECT SOLDER NG IC4 1,4,40,41,43,44 pin IC6 1,4,40,41,43,44 pin OK CHECK RESISTANCE BETWEEN CHECK +24V AT R1,R2,R6, AND R7 CHECK +24 PATTERN +24V AND GND. SHORT OR NOT NG NO SHORT OK REPLACE PRINTER PWB CHECK +5V AT IC4 AND IC
Resumo do conteúdo contido na página número 11
UX-2200CMU/CMC FO-2150CMU/CMC [6]How to Decide the Number of the Wrong Nozzle FUNC + 6 + + “CLEAN NOZZLES” A B Nozzle 1 Nozzle 56 .... Horizontal lines on A and B correspond to nozzle #1,#2 #56 from left side to right side. If there are missing horizontal lines, you can decide the number of wrong nozzle from pattern A or B . Note) Don’t use the check pattern to decide the number of wrong nozzle. – 10 –
Resumo do conteúdo contido na página número 12
UX-2200CMU/CMC FO-2150CMU/CMC TABLE 1. TABLE 2. (Nozzle# IC-PIN CONNECTOR-PIN) (Nozzle Common CN) Nozzle# IC PIN CN PIN Nozzle# PIN CN PIN Nozzle# IC PIN CN PIN 1 6 39 3 9 29 6 1,3,5,7,9,11,13,15, 10 3 20 2 4 39 4 28 30 4 10 17,19,21,23,25,27 1 3 8 4 17 3 6 35 3 10 31 6 14 3 21 2,4,6,8,10,12,14,16, 4 4 35 4 27 32 4 14 4 16 18,20,22,24,26,28 2 4 29 5 6 31 3 11 33 6 22 3 30 29,31,33,35,37,39,41, 6 2 4 31 4 26 34 4 22 4 7 43,45,47,49,51,53,55 3 4 7 6 25 30,32,34,36,38,40,42, 3 12 35 6 9 3 22 8 4 25
Resumo do conteúdo contido na página número 13
UX-2200CMU/CMC FO-2150CMU/CMC [7] Waveforms FEED MOTOR WAVEFORMS WHEN FEEDING PAPER T Stopped CH1=50V CH2=50V CH3=50V CH4=50V 2ms / d DC P:10 DC P:10 DC P:10 DC P:10 T:1.92ms 1/ T:520.8Hz CN1-2 1 G CN1-3 G 2 CN1-4 3 G CN1-5 4 G G : 0V Figure 1 – 12 –
Resumo do conteúdo contido na página número 14
UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOTOR WAVEFORMS T Stopped CH1=20V CH2=20V CH3=20V CH4=20V 20s / d DC P:10 DC P:10 DC P:10 DC P:10 T:19.2¨s 1/ T:52.08kHz CN2-1 1 CN2-2 2 CN2-3 3 CN2-4 4 When the cartridge holder is at the position of replacing cartridge. Figure 2 T Stopped CH1=20V CH2=20V CH3=20V CH4=20V 1ms / d DC P:10 DC P:10 DC P:10 DC P:10 T:960¨s 1/ T:1.042kHz CN2-1 1 CN2-2 2 CN2-3 3 CN2-4 4 Measured for printing check pattern Figure 3 – 13 –
Resumo do conteúdo contido na página número 15
UX-2200CMU/CMC FO-2150CMU/CMC CARRIAGE MOTOR WAVEFORMS MEASURED FOR CHECKING OUT OF INK T Stopped CH1=20V CH2=20V CH3=20V CH4=20V 2ms / d DC P:10 DC P:10 DC P:10 DC P:10 T:1.92¨ms 1/ T:520.8Hz CN2-1 1 CN2-2 2 CN2-3 3 CN2-4 4 Figure 4 T Stopped CH1=20V CH2=20V CH3=20V CH4=20V 500s / d DC P:10 DC P:10 DC P:10 DC P:10 T:480¨s 1/ T:2.083kHz CN2-1 1 CN2-2 2 CN2-3 3 CN2-4 4 Figure 5 – 14 –
Resumo do conteúdo contido na página número 16
UX-2200CMU/CMC FO-2150CMU/CMC [8] Service Checks 1. Carrier Transport Service Check FRU Action System Board Check the motor for binds,or loose motor pulley. 1 Turn the printer off and disconnect CN2 from the system board.Check for motor pins shorted to the motor housing.If you find a pin shorted to the housing,replace the motor. If the failure remains,replace the system board. Carrier Transport A noisy or chattering motor or a motor that fails to turn can be caused 2 Motor by: • An open or short
Resumo do conteúdo contido na página número 17
UX-2200CMU/CMC FO-2150CMU/CMC 2. Envelope Feed Service Check FRU Action Envelope Guide Be sure the envelope guide has been turned to the envelope load 1 position. Be sure the envelope guide is against the envelopes. Perform the ‘Paper Feed Service Check’on page 4. 3. Maintenance Station Service Check The maintenance station has two functions: Cleans the printhead nozzles during the print operation. • Seals the printhead when it is not being used to prevent the nozzles from drying. • FRU Acti
Resumo do conteúdo contido na página número 18
UX-2200CMU/CMC FO-2150CMU/CMC 4. Paper Feed Service Check If your machine does not have paper jam problems, continue with the service check. If your machine does have a paper jam problem,examine it for the following before you begin the service check: Check the entire paper path for obstructions. • Be sure there is not too much paper in the sheet feeder. • Be sure the correct type of paper is being used. • Check for static in the paper. • FRU Action System Board Turn the printer on and v
Resumo do conteúdo contido na página número 19
UX-2200CMU/CMC FO-2150CMU/CMC 5. Paper Path Service Check Examine the machine for the following before you being this service check: Check the entire paper path for obstructions • Be sure the correct type of paper is being used. • Be sure the printer is installed on a flat surface. • FRU Action Large and Small Feed Check for wear and binds. 1 Rollers Small Feed Roller Check for damage. 2 Springs Auto Sheet Feeder Check the pick rollers for wear. 3 Mid-Frame Asm Check the following for wear
Resumo do conteúdo contido na página número 20
UX-2200CMU/CMC FO-2150CMU/CMC [9] IC Signal Name IC 8 : VHiTMP87PH47U (TMP87C807U) 1. Pin Assignment (Top View) P15(TC2) 34 22 P63 P16 35 21 P62 P17 36 20 P61 (INT5/STOP)P20 37 19 P60 (XTIN)P21 38 18 N.C. (XTOUT)P22 39 17 VSS VDD 40 16 XOUT (HSO)P77 41 15 XIN (HSCK)P76 42 14 RESET (SO)P75 43 13 TEST (SI)P74 44 12 P00 2. Block Diagram VDD Power Supply VSS P S W Stack Pointer Program Counter Data Memory RBS Flags (RAM) ALU Register Banks RESET Reset I/O System Controller Test pin Program Mem
