Resumo do conteúdo contido na página número 1
µ
Paper type: Wood Free 80g/m2, Paper Thickness=100 m // Pages in book=16 // Print scale=81%
Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 0 mm
MAINTENANCE KIT
Type 400
Operating Instructions
Printed in China
GB GB
EN USA G830-8600
Resumo do conteúdo contido na página número 2
µ Paper type: Wood Free 80g/m2, Paper Thickness=100 m // Pages in book=16 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 0 mm Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. Copyright © 2003
Resumo do conteúdo contido na página número 3
CassisP1GBmaintenance-F2_FM.book Page i Friday, May 23, 2003 10:04 AM TABLE OF CONTENTS Trademarks.............................................................................................................1 1. Replace Maintenance Kit Before Replacing ...................................................................................................3 Checking the contents of the box...............................................................................3 Preparing to replace the parts
Resumo do conteúdo contido na página número 4
CassisP1GBmaintenance-F2_FM.book Page ii Friday, May 23, 2003 10:04 AM ii
Resumo do conteúdo contido na página número 5
CassisP1GBmaintenance-F2_FM.book Page 1 Friday, May 23, 2003 10:04 AM Trademarks Microsoft, Windows, and Windows NT are registered trademarks of Microsoft@ Corporation in the United States and/or other countries. Other product names used herein are for identification purposes only and might be trademarks of their respective companies. We disclaim any and all rights in- volved with those marks. Notes: Some illustrations in this manual might be slightly different from the machine. Certain optio
Resumo do conteúdo contido na página número 6
CassisP1GBmaintenance-F2_FM.book Page 2 Friday, May 23, 2003 10:04 AM 2
Resumo do conteúdo contido na página número 7
CassisP1GBmaintenance-F2_FM.book Page 3 Friday, May 23, 2003 10:04 AM 1. Replace Maintenance Kit The maintenance kit contains parts necessary for maintaining the printer. When “Replace Maintenance Kit” appears on the panel display, install the replace- ment parts included in the maintenance kit. R WARNING: • It is dangerous to handle the plug with wet hands. An electric shock might occur. R CAUTION: • The inside of the machine could be very hot. Do not touch the parts with a label indicatin
Resumo do conteúdo contido na página número 8
CassisP1GBmaintenance-F2_FM.book Page 4 Friday, May 23, 2003 10:04 AM Replace Maintenance Kit Description Quantity Transfer roller 1 pc ⇒ p.8 “Replacing the Transfer Roller” 1 Gloves 1 pair Fusing Unit 1 pc ⇒ p.10 “Replacing the Fusing Unit”. Preparing to replace the parts You should replace all the parts included in Maintenance Kit at the same time. Be sure to replace them in the following order: AA Check the contents of the box for the following items: AA Friction pad Paper feed rolle
Resumo do conteúdo contido na página número 9
CassisP1GBmaintenance-F2_FM.book Page 5 Friday, May 23, 2003 10:04 AM Replacing Parts Replacing Parts CCCCRemove paper from the paper Replacing the Friction Pad tray. Place the tray upside down 1 on a flat surface. Replace all the friction pads in the tray. The following procedure shows how to replace the tray's friction pad (Tray1). AAAA Pull out the paper tray until it stops. ZKEM160E DDUse a sharp-pointed item like a DD ball-point pen, to release the two catches that lock the friction pad.
Resumo do conteúdo contido na página número 10
CassisP1GBmaintenance-F2_FM.book Page 6 Friday, May 23, 2003 10:04 AM Replace Maintenance Kit EEEE Return the paper tray to its origi- GGGG If your printer is equipped with nal position, and remove the fric- the optional Paper Feed Unit(s), tion pad from the tray. follow the same procedure when replacing the friction pad. Note 1 ❒ The friction pad spring may come off. Be careful the spring Replacing the Paper Feed does not fall off and become Rollers lost. Replace all feed rollers including
Resumo do conteúdo contido na página número 11
CassisP1GBmaintenance-F2_FM.book Page 7 Friday, May 23, 2003 10:04 AM Replacing Parts Important DDDD While sliding the green lock lever to the right (AAAA), set the new roller ❒ Be sure to move the printer hor- izontally. Moving the printer (BBBB). After that, return the green lock lever to its original position facing up on down may cause the toner to scatter. (CCCC). 1 ❒ Do not put the printer on an un- stable or tilted surface. Note ❒ If the printer is equipped with the optional Paper Feed
Resumo do conteúdo contido na página número 12
CassisP1GBmaintenance-F2_FM.book Page 8 Friday, May 23, 2003 10:04 AM Replace Maintenance Kit DDDD Hold the lock levers (green parts), Replacing the Transfer Roller and pull them. AAAAWhile holding the front cover with both hands on the left and 1 right sides, press the release but- ton to open it. ZKEM200E EEEE Hold the green parts of the roller on both sides, and remove the roller from the printer as shown ZKEH120E in the illustration. BB Pull the toner cartridge out of the BB printer, whil
Resumo do conteúdo contido na página número 13
CassisP1GBmaintenance-F2_FM.book Page 9 Friday, May 23, 2003 10:04 AM Replacing Parts Important IIII Lower the toner cartridge when it touches the back. ❒ Do not insert the roller on the back of the socket, or the printer might be damaged. 1 ❒ Insert the metallic part of the roller on the socket. If you insert the sponge part of the roller, the roller might be damaged. GGGGPush down the green parts of both sides of the roller until it clicks as shown in the illustration. ZKET140E JJJJ Close t
Resumo do conteúdo contido na página número 14
CassisP1GBmaintenance-F2_FM.book Page 10 Friday, May 23, 2003 10:04 AM Replace Maintenance Kit BBBB Lift the lock levers of the fusing Replacing the Fusing Unit unit as shown in the illustration. R CAUTION: • The fusing unit becomes very 1 hot. When installing the new fus- ing unit, turn off the printer and wait about an hour. After that, in- stall the new fusing unit. Not waiting for the unit to cool down can result in a burn. ZKEX222E AA If the rear cover is attached to the AA printer,
Resumo do conteúdo contido na página número 15
CassisP1GBmaintenance-F2_FM.book Page 11 Friday, May 23, 2003 10:04 AM Replacing Parts A Insert the rear cover to the in- EEEE Replace the new fusing unit into side grooves on both sides of the printer. the printer in a horizontal di- rection. 1 ZKEX224E ZKEX221E FFFF Push the lock levers of the fusing unit down until it clicks. B Close the rear cover. Proceed to step . I ZKEX225E ZKEX211E GGGG Reinstall the rear cover removed in step . AAAA HHHH Reinstall the optional Duplex Unit if it was r
Resumo do conteúdo contido na página número 16
CassisP1GBmaintenance-F2_FM.book Page 12 Friday, May 23, 2003 10:04 AM INDEX F friction pad, 5 fusing unit, 10 P paper feed roller, 6 T transfer roller, 8 12
Resumo do conteúdo contido na página número 17
CassisP1GBmaintenance-F2_FM.book Page 13 Friday, May 23, 2003 10:04 AM MEMO 13
Resumo do conteúdo contido na página número 18
CassisP1GBmaintenance-F2_FM.book Page 14 Friday, May 23, 2003 10:04 AM MEMO 14 GB GB EN USA G830-8600
Resumo do conteúdo contido na página número 19
µ Paper type: Wood Free 80g/m2, Paper Thickness=100 m // Pages in book=16 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 0 mm Introduction This manual describes detailed instructions on the operation and notes about the use of this machine. To get maximum versatility from this machine all operators are requested to read this manual carefully and follow the instructions. Please keep this manual in a handy place near the machine. Copyright © 2003
Resumo do conteúdo contido na página número 20
µ Paper type: Wood Free 80g/m2, Paper Thickness=100 m // Pages in book=16 // Print scale=81% Gap (when printed at 81% scale) = Pages in book × Paper thickness / 2 = 0 mm MAINTENANCE KIT Type 400 Operating Instructions Printed in China GB GB EN USA G830-8600
