Resumo do conteúdo contido na página número 1
PRINTER
PP-505
(For FE-700)
Resumo do conteúdo contido na página número 2
SAFETY INSTRUCTIONS Safety Information for Operator Safety Information for Installer WARNING WARNING Do not open the cover of ELECTRICAL SHOCK HAZARD the equipment. Only qualified personnel should work inside the This equipment uses high equipment. voltage electricity which can shock or burn. This equipment uses high Only qualified personnel voltage electricity which can should work inside the shock or burn. equipment. Turn off the power at the ship's mains Do not disassemble or modify the sw
Resumo do conteúdo contido na página número 3
WARNING LABEL A warning label is attached to the printer. Do not remove the label. If the label is missing or damaged, contact your dealer about replacement. Name: Warning Label (1) WARNING Type: 86-003-1011 To avoid electrical shock, do not remove cover. No user-serviceable Code No.: 100-236-231 parts inside. ii
Resumo do conteúdo contido na página número 4
FOREWORD A Word to the Owner of the PP-505 Congratulations on your choice of the FURUNO PP-505 Printer. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your printer is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended fun
Resumo do conteúdo contido na página número 5
TABLE OF CONTENTS 1. OPERATION..................................................................................................1 1.1 General..............................................................................................................................1 1.2 Panel.................................................................................................................................1 1.3 Turning on the Power.........................................................
Resumo do conteúdo contido na página número 6
1. OPERATION 1.1 General 1.2 Panel Operation of the PP-505 is simple; just turn Power Switch on the power. The depth graph or the log, whichever is selected for printing, is printed PRINTER PP-505 out at the interval set. GRAPH LOG PAPER MODE Below are example printouts. INTERVAL POWER ON RANGE FEED/MARK Thermal Paper 2003/12/01 13:05:00 038.6m/01.0m 35 20.02’N/135 45.15’E 15.1kt 008.0deg Cover M GRAPH LED LOG PAPER 13:05:00 20m 40m 60m 80m 100m MODE INTERVAL Marker Depth
Resumo do conteúdo contido na página número 7
OPERATION Changing the mode Feeding the paper/Printing the marker Press the [MODE] key to change the printing To feed the paper, press and hold down the mode from depth graph to log printing [FEED/MARK] key. alternately. Press the [FEED/MARK] key momentarily to The printing interval setting is printed print the marker. whenever the [MODE] key is pressed. 1.3 Turning on the Power Changing the printing interval Flip down the thermal paper cover and turn Press the [INTERVAL] key
Resumo do conteúdo contido na página número 8
2. REPLACEMENT OF THERMAL PAPER When the thermal paper runs out, the PAPER LED blinks, printing stops automatically and Adhesive may the audible alarm sounds for five seconds. remain on the paper Tape With 1 m of paper remaining, a red paper end after tape is removed. This may cause a mark appears on the paper. When the red paper jam, so cut mark appears, replace the thermal paper as paper to remove Adhesive shown in the procedure below. adhesive. REQUIRED THERMAL PAPER Typ
Resumo do conteúdo contido na página número 9
3. INSTALLATION 3.1 Complete Set Name Type Mass Qty Remark 3.1 kg Main Unit PP-505 1 (with hanger) Spare Parts SP08-01600 1 Installation CP16-00800 1 Materials Accessories FP08-00500 1 Flush Mount Kit OP08-4 1 Option (004-511-330) Heat accumulation 3.2 General Mounting Considerations The PP-505 consumes very little power, so there is no need for forced air ventilation. This equipment can perform its intended However, it is recommended to provide at functions only if it is installed p
Resumo do conteúdo contido na página número 10
3. INSTALLATION 3.3 Tabletop/Bulkhead 3.4 Flush Mount Mount Flush mount panel kit is optionally supplied. The main unit can be mounted on a desktop, bulkhead, or in a panel. Make sure the Flush mount kit OP08-4 selected location is strong enough to support (Code No.: 004-511-330) the main unit against possible vibration and shock. If necessary, appropriate Name Type Code No. Qty reinforcement measures should be made on Flush 22-008-0125 100-103-351 1 the mounting area. mo
Resumo do conteúdo contido na página número 11
3. INSTALLATION 1. Referring to the illustration below, prepare 3.5 Wiring a cutout in the mounting area and drill four Refer to the interconnection diagram at end pilot holes for the flush mount angles. of manual for connection. Refer to the outline drawing at end of manual. 2. Fix the liner and the flush mount angles to the main unit. 3. Connect the cables at the rear of main unit. 4. Fix the main unit to the panel cutout with four tapping screws. 5. Fix the flush mount pan
Resumo do conteúdo contido na página número 12
4. MAINTENANCE Checking the power connector Fuse Replacement Check for loosened or disconnected power To protect the equipment from serious connector. damage, a 3A fuse is provided on the rear cabinet of the main unit. The fuse protects against overvoltage/reverse polarity of the WARNING ship’s mains or internal fault of the equipment. Do not open the cover of If the fuse has blown, first find out the cause the equipment. of the trouble before replacing it. A fuse rated for more than
Resumo do conteúdo contido na página número 13
APPENDIX REPLACEMENT OF PRINTER ASSEMBLY/TERMAL HEAD 1. Loosen the four M4 × 15 screws fixing the 4. Move the carriage to position A by rear cabinet to the main unit assembly. rotating the carriage shaft by fingers, as 2. Disconnect the connectors connected to shown below, where the thermal head the rear cabinet to detach the rear assembly can be replaced easily. cabinet. Carriage Shaft Carriage Rear Cabinet A P1 NH 4P P5 NH 6P M4 × 15 screw (4 pcs.) Main Unit Assembly 5. Rem
Resumo do conteúdo contido na página número 14
6. Pull out the connector end of the flexible 9. Hold the flexible cable end with a cable from the connector. Take care not to tweezers and pull it out until it is damage the flexible cable. positioned as shown below. Head Holder End of Flexible 180° 90° Cable (Connector) Thermal Head 7. Remove the thermal head from the head holder with a screwdriver as shown below, 10. Turn the head by 90° so that it is parallel and then take the thermal head assembly with the head holder as sho
Resumo do conteúdo contido na página número 15
11. Fix the flexible cable to the carriage with 12. Fold back the end of the cable and insert the flexible cable support, inserting the it into the connector. projection on the carriage into the hole of 180° the cable. End of Flexible Cable Flexible Cable Support Carriage Projection AP-3
Resumo do conteúdo contido na página número 16
FURUNO SPECIFICATIONS OF PRINTER PP-505 1 DATA FORMAT 1.1 Receiving System RS-232C 1.2 Speed 9600 bps 1.3 Data Length 8 bits 1.4 Parity Non 1.5 Stop Bit 1 bit 2 PRINTER SECTION 2.1 Printing System 9 dots serial thermal head printing system 2.2 Character Alphanumeric 2.3 Dot Pitch 0.28 mm/ dot 2.4 Number of Dot in Line 300 dots 2.5 Number of Characters Max. 80 characters/ line 2.6 Print Speed 31 characters/second 2.7 Roll Paper TP-0340, 112 mm (W) x 40 m (L) 3 RATED VOL
Resumo do conteúdo contido na página número 17
Resumo do conteúdo contido na página número 18
Resumo do conteúdo contido na página número 19
Resumo do conteúdo contido na página número 20
