Manual do usuário Epson LQ-570

Resumo do conteúdo contido na página número 1

LQ-570+
Printable columns:

80
10 wi
Buffer: 0 or 8 Kbytes (DIP-switch selectable)
character fonts:
Font Point 10.5
0 0 0
Epson
Epson 0 0 0
Epson Roman 0 0 0 0
LQ-570 and LQ-570+ Differences
LQ-570 LQ-570+
Acoustic Noise: 55dB( A) 465dB(A)
Scalable Fonts: 2 4
Epson Roman Epson Roman
Epson Sans Serif
Epson Sans Serif
You can also select other font/pitch combinations using ESC/P 2
Epson Roman T
Epson Sans Serif H commands.
Print speed: 315cps (15cpi draft) 337 cps (15cpi draft)
Scalable fonts:

Resumo do conteúdo contido na página número 2

Dimensions and weight: Labels: 63.5x23.8mm(2%x15/16imhes) Size 160mm (6.3 inches) Height 101x23.8mm(4x15/16inches) Width 434mm(17.1 inches) 101x27mm(4x17/16inches) Depth 368mm(14.5 inches) Thickness 0.07 to 0.09 mm (0.0028 to 0.0031 inches) for Weight 6.7 kg (14.8 lb) backing sheet 0.16 to 0.19 mm (0.0063 to 0.0075 inches) total Electrical l Use continuous type labels only. Rated voltage: AC 120 V (120 V model) l Use labels only under normal temperature and humidity conditions. Input voltage ran

Resumo do conteúdo contido na página número 3

LQ-570+ The Control Panel ALT While holding down this button, pressing certain other buttons The indicator lights give you the current status of the printer. The buttons let you control many of the printer settings. results in the following: BUFFER CLEAR (PAUSE) clears the printer’s buffer and initializes the printer settings MICRO FEED :h ? (LOAD/EJECT) feeds paper forward in l/ 180-inc increments & (LF/FF) feed paper backward in 1/18@inch increments Lights Bin Select/TEAR OFF This button selec

Resumo do conteúdo contido na página número 4

Table 2 DIP switch 2 lnternational character sets SW ON ( OFF DIP switch 1 2-l Page length (for See Table 5 below 24 60 2-2 tSe[\J^‘{:)’ 2-3 1 Tear off 1 On 1 off 2-4 / Auto line feed I On I off 1 France 2 Germany 3 E $ e [ \ J A t { i } * Table 3 lnternationd character sets 4 Denmark I Off On On 5 Sweden Off Off On Off ‘3W 7 I R s e j w i - t ,, OffOffOffOff The following eight additional sets are available only by using the ESC R software command. Off Off On off Additional inte

Resumo do conteúdo contido na página número 5

LQ-570+ Input buffer capacity Connector pin assignments and a description of their respective interface signals are shown in the following table. The printer stores print data. sent from your computer in its input buffer. Keep DIP switch 1-7 off to select an 8Kbyte buffer. Signal Pin Pin . Skip-over-perforation. I 19 STROBE IN STROBE pulse to read data. Pulse wrdth must be more than 1 at the receiving Turning DIP switch l-8 on when you are using continuous paper enables the skip-over-perforatio

Resumo do conteúdo contido na página número 6

LQ-570+ Paper: Interface timing Slngk sheets The figure below shows the timing for the parallel interface: 18 2 t o 21 6 mm Width (7.17 to 18 2 t o 21 6 mm 16 5 t o 24 1 mm (7.17 to (6.60 to 9.49 Inches) STROBE Paper storage conditions: Temperature: 18” to 22°C (64” to 72OF) Humidity: 40% to 60% Environmental Interface Cards Temperature: Operation 5” to 35°C (41” to 95°F) Storage: -30” to 60°C (-22” to 140°F) You can use optional interface boards to supplement your printer’s Humidity (witho

Resumo do conteúdo contido na página número 7

LQ-570+ Non-recommended Commands Information Reference List Epson recommends against using the following commands because some of these commands are not supported in existing printers and Engineering Change Notices some are duplicates of other commands. None. BEL Backspace Bs Product Support Bulletins DC1 select printer None. Deselect printer Technical Information Bulletins CAN Cancel data EsC# Cancel MSB control None. E!3< Unidirectional printing for one Iine Related Documentation ESC= SetMSBto