Resumo do conteúdo contido na página número 1
iDP-3540/41 User’s Manual
CITIZEN
User’s Manual
MINI DOT MATRIX PRINTER
MODEL
iDP-3540/3541
Japan CBM Corporation
Information Systems Div.
CITIZEN 1/48
Resumo do conteúdo contido na página número 2
iDP-3540/41 User’s Manual 1995.09.04(10-DCL)1 Declaration of Conformity Manufacturer's Name : : Japan CBM Corporation Manufacturer's Address : 1-1-7, Okubo, Shinjuku-ku, Tokyo 169, Japan Declare the Product Product Name Dot Matrix Printer Model Number (s) iDP-3540, 3541 Series (iDP3540R, iDP3540P, iDP3541R, iDP3541P) (S.NO.50901072 - ) Conform to the following Standards LVD : EN60950 :1992+A1+A2:1993 EMC : EN
Resumo do conteúdo contido na página número 3
iDP-3540/41 User’s Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. * Do not use this product near water. * Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product. * Slots and open
Resumo do conteúdo contido na página número 4
iDP-3540/41 User’s Manual CONTENTS 1. Introduction ......................................................................................................................................................6 1-1. Features .....................................................................................................................................................6 1-2. Accessories....................................................................................................................
Resumo do conteúdo contido na página número 5
iDP-3540/41 User’s Manual 11-3. Slide Switch Setting (Serial interface specifications only)....................................................................32 11-4. Dip-Switch Location .............................................................................................................................32 12. Print Control Functions.................................................................................................................................33 12-1. Control Codes......
Resumo do conteúdo contido na página número 6
iDP-3540/41 User’s Manual 1. Introduction The iDP3540 is a dot impact printer which can be utilized for a wide range of applications, such as data communications terminals, P.O.S. terminals and kitchen printers. High speed performance is made possible by a bi-directional printing system and, since this printer is compact, lightweight and equipped with an abundance of functions, they can be easily employed for a variety of different tasks. The iDP3541 has a built-in automatic cutter capable of pe
Resumo do conteúdo contido na página número 7
iDP-3540/41 User’s Manual 2. Basic Specifications 2-1. Type classifications Printer types are classified according to the system shown below. iDP 3540 F 23 P J 120 G B P 28 R F 220 N 40 X 240 I Idp 3541 F IDP 3540 – F 23 R J 100 – G B Model Memory Back-up IDP3540 B: With Back-up IDP3541: With Auto Cutter
Resumo do conteúdo contido na página número 8
iDP-3540/41 User’s Manual 3. Specifications 3-1. General Specifications Item iDP3540F iDP3540P iDP3541 1 Print Method Bidirectional serial dot impact method 2 Character 7 × 7 dots (incl. Half-dot) composition Character Printer DP-610: 23 columns 230 dots/line 3 number per DP-612: 28 columns 280 dots/line line DP-614: 40 columns 360 dots/line DP-617G: 40 columns 400 dots/line Printer DP-610: 23 columns approx 4.0 line/sec. 4 Print speed DP-612: 28 columns approx 3.0 line/sec.
Resumo do conteúdo contido na página número 9
iDP-3540/41 User’s Manual *1 Input buffer can be selected by setting the DIP switch. *2 However, when the input buffer is set for two lines, back-up of graphic data is not possible. *3 Single color cassette ribbon is available as option. Black print: IR-61B Purple print: IR-61P CITIZEN 9/48
Resumo do conteúdo contido na página número 10
iDP-3540/41 User’s Manual 4. Block Diagram CITIZEN 10/48
Resumo do conteúdo contido na página número 11
iDP-3540/41 User’s Manual 5. External Appearance and parts Description 5-1. External appearance and parts names Model : iDP3540 CITIZEN 11/48
Resumo do conteúdo contido na página número 12
iDP-3540/41 User’s Manual 5-2. External appearance and parts names Model : iDP3541 CITIZEN 12/48
Resumo do conteúdo contido na página número 13
iDP-3540/41 User’s Manual 5-3. Parts Descriptions (1) Power Cord Insert the plug end into an electric outlet. (2) Power Switch Power is supplied to the printer by turning this switch on. (3) Power Lamp This lights up when the power switch is “ON” and goes out when turning “OFF”. (4) SEL / ALARM Lamp This lights up when the printer is in SELECT state (ON-LINE) and goes out when in DESELECT state (OFF- LINE). The printer can print out the data only when this lamp
Resumo do conteúdo contido na página número 14
iDP-3540/41 User’s Manual 6. Preparation 6-1. Inserting / Removing the Printer Cover Inserting and removing the printer cover as shown in Fig. 1, 2. Fig. 1 Fig. 2 6-2. Opening and Closing the Cutter Unit (iDP3541) 1) To open the unit, grasp two levers and lift upward. 2) When closing the unit, press downward until it completely lock place. Fig. 3 CITIZEN 14/48
Resumo do conteúdo contido na página número 15
iDP-3540/41 User’s Manual 6-3. The Ribbon Cassette Installation To insert the ribbon, disconnect the power source beforehand. If the printer has been printing for many hours, be careful not to touch the printer head as it might be hot. 1) Remove the printer cover 2) While inserting the ribbon into the space between the print head and the ribbon guide, press the cassette into the holder unit it clicks into place. (Ref. to Fig. 4&5) 3) Turn the cassette ribbon knob in the direction of the arrow to
Resumo do conteúdo contido na página número 16
iDP-3540/41 User’s Manual 6-4. Loading and Changing the Paper 6-4-1. Using Paper Roll (iDP3540F, 3541) 1) Cut the paper in right angle to its longitudinal center line as shown in Fig. 7. 2) Insert the paper into insertion inlet on the rear side of printer. 3) Turn on the power switch and feed the paper by pushing the LF switch. 4) When the printing paper comes out of the clearance (paper cutter part) on the printer cover, fix the paper by means of paper holder, then set in on the main unit. CIT
Resumo do conteúdo contido na página número 17
iDP-3540/41 User’s Manual 6-4-2. Using Fan-Fold Paper (iDP3540P) 1) Remove the printer cover 2) Set the imprint face of the paper downward and put into the paper entrance. 3) If necessary to adjust the sprocket-wheel’s position, free the wheels using the lever on both sides. Slide them to the appropriate position, and lock them back. 4) Hook some of the paper’s perforations on the sprockets and forward the paper into the printer mechanism by pulling and turning the paper-feed knob until the pape
Resumo do conteúdo contido na página número 18
iDP-3540/41 User’s Manual 6-6. Self Test Printing Your printer has a built in self print function for purpose of checking print operation without the need for any other external device. Procedures for Actuating the Print Function 1) Be sure that a paper roll is properly loaded. 2) Confirm that the ribbon cassette is properly installed and turn the power switch off. 3) Turn the power switch ON while pressing the LF switch, and release the LF switch after the self test operation has begun. In t
Resumo do conteúdo contido na página número 19
iDP-3540/41 User’s Manual 8. Parallel Interface 8-1. Specifications a) Data Input system : 8 bit parallel (DATA 1~8) b) Control Signals : ACK, BUSY, STB, FAULT, PE, RESET c) Compatible Connector : Printer side : 57LE-40360 (AMPHENOL or equivalent) : Cable side : 57-30360 (AMPHENOL or equivalent) 8-2. Connector Pin Assignment Pin No. Signal Name Pin No. Signal Name 1 STB 19 Twisted Pair GND 2DATA 1 20 ² 3DATA 2 21 ² 4DATA 3 22 ² 5DATA 4 23 ² 6DATA 5 24 ² 7DATA 6 25 ² 8DATA 7 26 ² 9D
Resumo do conteúdo contido na página número 20
iDP-3540/41 User’s Manual 8-3. Description of Input / Output Signals 8-3-1. Input / Output Signals a) Input / Output Signals *DATA : 8 bit parallel signal. (Positive logic) *STB : A strobe signal for reading in 8 bit data. (Negative logic) *RESET : A signal which resets the entire printer. (Negative logic, 1 ms or more) b) Output Signals (From Printer) *ACK : This is a pulse signal for requesting 8 bit data, issued at the end of a BUSY signal. (Negative logic) *BUSY : This signal
