Resumo do conteúdo contido na página número 1
12 volt Jump-start
and power supply
38391
set up and operating instructions
note: after purchase
and before initial use
of the Jump-start,
fully charge the Jump-
start battery until the
dc charging led
turns off.
after each jump start,
fully recharge the
battery until the dc
charging led turns
off.
Fully charge Jump-
start battery every 30
days to ensure long
battery life.
visit our website at: http://www.harborfreight.com
read this material b
Resumo do conteúdo contido na página número 2
lighted. Do not use in the presence speciFications of flammable gases or liquids. Start Amps 400 3. Keep children away. Children must Peak Amps 900 Battery 12 V, 17 Ah, Lead-Acid, never be allowed in the work area. Rechargeable Do not let them handle this product. Charging Current = 0.18A Booster Cables #4 Gauge, 17” Length 4. store idle equipment. When not Includes: 12 Volt Cigarette Lighter Charger, in use, tools must be stored in a dry AC Adapter Receptacle, Built-in Light, loca
Resumo do conteúdo contido na página número 3
10. stay alert. Watch what you are clamps only. Keep it in the “off” doing, use common sense. Do not position except when jumpstarting. operate any tool when you are tired. 17. Lead-acid batteries vent hydrogen gas during normal operation and 11. check for damaged parts . Before charging. Hydrogen is highly using any tool, any part that appears flammable and explosive. Charge damaged should be carefully checked batteries only in a well-ventilated to determine that it will operate
Resumo do conteúdo contido na página número 4
120 v~ charging controls and components Jump Start ON/OFF Black Red Work Test Clamp Clamp Light Meter Cigarette Lighter Plug-In Power Cord (5) Figure 2 1. Plug the Power Cord (5) into a wall outlet and plug the female end of the Power Cord into the 120V male Charging Plug of the 120V~ Charging Port (see Figure 2, above). 2. Before first use, fully charge the Jump-start battery until the dc Voltage Charging 120 V
Resumo do conteúdo contido na página número 5
o note: The LED light will go on (when note: Charging room temperature: 50 F o Switch is in the OFF position) to - 104 F. indicate a reverse polarity condition. operation 12 vdc charging using the Jump-start as a 12 vdc note: This system is equipped with a 12 power source VDC Cigarette Lighter Adapter so you can charge the Jump-Start from a warning!! the on/off switch (see vehicle or boat battery. This method Figure 1) regulates power to the of recharging will not charge the cla
Resumo do conteúdo contido na página número 6
If you use the Jump-Start with a Jump starting a v ehicle power inverter (not included) as a 1. note: Press the Light Switch to 120 V~ power source, Table 3 will activate Work Light in case it is give you approximate times to expect needed. with a fully charged unit. 2. Attach the red (+) Clamp (1) to the t able 3 red (+) positive battery terminal. 120 V~ Power Source Usage Times using a power inverter (not included) 3. Attach the black (-) Clamp (2) to a estimated estimated non-movi
Resumo do conteúdo contido na página número 7
recharging using 12 vdc supply battery replacement 1. Insert the Cigarette Lighter Recharger 1. Remove the eight screws around the Plug into the Front Panel port labeled back panel and lift off the cover plate. recharge . Lift out the battery. 2. Insert the other end of the Cigarette note: Notice how the red and black Lighter Recharger Cord into the 12 cables connect to the old battery and VAC Cigarette lighter receptacle on make sure to keep them in place, your vehicle or boat. connectin
Resumo do conteúdo contido na página número 8
parts list and assembly drawing part description 1 Red Clamp 2 Black Clamp 3 Light Bulb 4 Battery (Internal, not shown) 5 Power Cord 6 Cigarette Lighter Recharger 3 5 1 2 6 please read the Following careFully THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR
Resumo do conteúdo contido na página número 9
limited 90 day warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
