Resumo do conteúdo contido na página número 1
®
FALCON ELECTRIC INC.
SVR SERIES
PRECISION UTILITY VOLTAGE
REGULATOR AND CONDITIONER
OWNER’S MANUAL
SVR1K-1T & SVR2K-2T
SVR2K-1T &SVR2K-2T
SVR3K-1 & SVR3K-2T
®
FALCON Electric Inc., 5106 Azusa Canyon Rd., Irwindale, California 91706 800-842-6940 Fax: 626-962-7720 Email: sales@falconups.com
®
2005 Falcon Electric Inc. All rights reserved.
All other brand names and trademarks are the property of their respective owners.
Resumo do conteúdo contido na página número 2
SVR SERIES FEATURES • COMPACT SIZE, LIGHT WEIGHT • WIDE INPUT VOLTAGE WINDOW • TIGHT OUTPUT VOLTAGE REGULATION (±2%) • INPUT POWER FACTOR CORRECTION • SURGE PROTECTION • HIGH EFFICIENCY • OVER CREST RATIO LED INDICATOR • RS-232 INTERFACE SYSTEM BLOCK DIAGRAM OM48021-1 Rev. C 2
Resumo do conteúdo contido na página número 3
This following User’s Manual is provided to better enhance your understanding of the product and ensure its proper installation and usage. Reading this manual carefully prior to installation of the SVR Series Precision Utility Voltage Regulator and Conditioner will save time and ensure worry-free operation. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important safety instructions that must be followed during the installation, operation and ma
Resumo do conteúdo contido na página número 4
CARE & MAINTENANCE The SVR Series Precision Utility Voltage Regulator and Conditioner is designed to be maintenance-free. It can be cleaned with a damp cloth or nonabrasive cleanser providing it is turned off and the input plug is disconnected from the utility source. Be sure vents and fans are kept free from accumulation of dust, dirt or lint. ® FALCON ELECTRIC SVR SERIES INSTALLATION AND STARTUP CHECK LIST 1. Verify the following is included in the SVR shipping carton
Resumo do conteúdo contido na página número 5
FRONT PANEL INDICATOR AND FUNCTION KEYS 5 1 6 4 8 7 2 3 LOAD LEVEL INDICATOR LEDS 1 • The first or bottom LED is lit when the output load is greater than 25% of the rated output of the SVR. • The second LED is lit when the output load is greater than 50% of the rated output of the SVR. • The third LED is lit when the output load is greater than 75% of the rated output of the SVR. 2 BYPASS INDICATOR LED (Not on frequency converter m
Resumo do conteúdo contido na página número 6
5 FAULT INDICATOR LED This LED is lit during the following conditions: • The inverter voltage is too high or low. • SVR over temperature condition. • Internal DC Bus has an under or over voltage condition. • Internal microprocessor or memory failure. 6 ON / OFF BUTTON The following describes the different modes of operation for this button: • Pressing this button while the SVR is on and utility is present will turn the SVR inverter an
Resumo do conteúdo contido na página número 7
Audiable Alarms Audible alarm signals are divided into two catagories. Each category represents a different level of alarm status. Catagory One Alarms represent normal or correctable operational alarms. Category Two Alarms are sounded in the event of abnormal operation This will provide the end-user a more detailed notification of the SVR’s status. 1. Category One Alarms: • One long beep prior to a short beep, lets the user know the SVR is in an OVER LOAD, OVER CREST, or
Resumo do conteúdo contido na página número 8
DIP SWITCH SETTINGS (All SVR 1kVA – 3kVA Models) OFF = 0 DIP SWITCHES SELECTION ON = 1 TABLE REAR PANEL VIEW FOR 100-120Vac NOMINAL LINE VOLTAGE SW2 SW1 VOLTAGE Down Down 100V Down Up 110V Up Down 120V Up Up 115V FOR 220-240Vac NOMINAL LINE VOLTAGE SW2 SW1 VOLTAGE Down Down 220V Down Up 230V Up Down 240V Up Up 200V SW3 – DISABLED Up GREEN MODE OFF (Default) NOTE: THE SVR MUST BE TURNED OFF AND BACK ON BEFORE NEW DIP SWITCH SETTINGS WILL BECOME ACTIVE
Resumo do conteúdo contido na página número 9
INSTALLATION DETAILS SVR1K-1, SVR2K-1, SVR3K-1, SVR1K-2T, SVR2K-2T & SVR3K-2T Tower Models TYPICAL FRONT VIEW Input Power Circuit Breaker (On the rear panel) Front Control panel Cooling Vents Must not be obstructed REAR VIEW SVR1K-1T DIP SWITCHES COVER PLATE FOR OPTIONAL SNMP AGENT RS- 232 CONNECTOR COOLING FAN DO NOT BLOCK OUTPUT INPUT CIRCUIT BREAKER RECEPTACLE
Resumo do conteúdo contido na página número 10
REAR VIEW SVR1K-2T DIP SWITCHES COVER PLATE FOR OPTIONAL SNMP AGENT RS- 232 CONNECTOR COOLING FAN DO NOT BLOCK OUTPUT INPUT FUSE RECEPTACLES 4 each IEC 320 POWER INLET OPTIONAL EXTERNAL BATTERY CONNECTOR REAR VIEW SVR2K-1T & SVR3K-1T DIP SWITCHES COVER PLATE FOR OPTIONAL SNMP AGENT RS- 232 CONNECTOR COOLING FANS DO NO BLOCK Optional Receptacle
Resumo do conteúdo contido na página número 11
REAR VIEW SVR2K-2T & SVR3K-2T DIP SWITCHES COVER PLATE FOR OPTIONAL SNMP AGENT RS- 232 CONNECTOR COOLING FANS DO NOT BLOCK OUTPUT FUSE S (2 places) OPUTPUT RECEPTACLES Shown with (1) L6 -20R & (2) 5- 20R Receptacles MAIN POWER SWITCH & INPUT CIRCUIT BREA KER LINE CORD IN LET OTHER OUTPUT RECEPTACLE CONFIGURATIONS AVAILABLE
Resumo do conteúdo contido na página número 12
GENERAL PROVISIONS FALCON® ELECTRIC INC. hereby warrants product shipped under this agreement to be free from defective workmanship for a period of two years following date of shipment. This Limited New Product Warranty Agreement only applies to covered repairs to the product occurring within the United States and Canada. EXCLUSIONS: The following are not covered by the Falcon Electric Limited New Product Warranty. 1. DAMAGE DUE TO ACCIDENTS, FRAUD, INTENTIONAL NEGLIGENCE, MISUSE,
Resumo do conteúdo contido na página número 13
FCC CONSIDERATIONS This equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. All models covered in this manual have been tested and found to comply with the limits for a Class A computing device, in accordance with the specifications in FCC regulations, Part 15, Subpart J, which are designed to provide reasonable protection against
