Resumo do conteúdo contido na página número 1
®
PowerClass
COMPONENT SPEAKER SYSTEM
Resumo do conteúdo contido na página número 2
INTRODUCTION ® Thank you for your purchase of this PowerClass Component Loudspeaker ™ System from PrecisionPower . Our engineers have combined state of the art materials such as foamed prolypropylene cones and vapor-deposit titanium dome tweeters with cutting edge industrial design to achieve competition-ready performance levels. ™ PRACTICE SAFE SOUND Continuous exposure to sound pressure levels over 100dB may cause permanent hearing loss. High power automotive sound systems can generate sound p
Resumo do conteúdo contido na página número 3
TOOLS OF THE TRADE Listed below are tools you may wish to have on hand before starting your installation. Having the proper tools will make the installation much easier. Some of these tools are necessities, some will just make the job easier. Marking Pen Phillips Scre wdriver Electric Drill Volt/Ohm Meter (Optional) 1/4" Drill Bit Assorted Tin Snips 1/8" Drill Bit Wire Cutters 3/8" Drill Bit Wire Crimpers Hole Saw Arbor Wire Strippers 4¾" Hole Saw (5¼” woofer install.)
Resumo do conteúdo contido na página número 4
REAR DECK MOUNTING In rear deck installations, check the operation of the trunk suspension springs or tension bars. These tension bars can move when opening and closing the trunk and can exert a great deal of force against anything that obstructs their movement, such as a speaker basket or motor assembly. In addition, try to avoid locating the speakers too close to the back edge of the rear deck. Installing the rearmost screws may not be possible without the removal of the rear window. INSTALLIN
Resumo do conteúdo contido na página número 5
Step 6: Using the plastic grille ring as a template, mark the mounting holes with a pen. Step 7: Pre-drill mounting holes using a 1/8" drill bit. WARNING: Window mechanisms and electrical wires and other expensive car parts have a nasty habit of hiding where you least expect. CHECK BEFORE YOU DRILL! Step 8: Pull the wire through the speaker opening and connect to the speaker. Be sure to observe proper midrange polarity during this process. Step 9: To mount the speaker, the speaker is placed thro
Resumo do conteúdo contido na página número 6
NOTE: To remove the trim ring from the tweeter housing: 1. Rotate the trim ring a few degrees in a clockwise direction until you feel a detent. 2. Remove the trim ring by lifting it straight up. INSTALLING THE TWEETER SURFACE MOUNTING Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Place the surface mount housing against the panel and mark the two holes at the rear of the housing. Step 3: Drill the smaller center hole usi
Resumo do conteúdo contido na página número 7
MOUNTING SCREWS SURFACE SURFACE MOUNT HOUSING MOUNT TRIM RING WIRING HARNESS TWEETER TWEETER WIRE PANEL FLUSH MOUNTING INTO REMOVED PANELS Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Mark the center point of the tweeter location. Step 3: If using a hole saw, first drill a pilot hole, then cut out the hole using a standard 2-1/8" hole saw. Step 4: If not using a hole saw, use either the cardboard packaging for the tweet
Resumo do conteúdo contido na página número 8
TRIM RING FLUSH MOUNT TWEETER WIRE HOUSING WIRING HARNESS FLUSH MOUNTING INTO MOUNTED PANELS Step 1: Determine the tweeter mounting location, then route the wires from the crossover to the tweeter location. Step 2: Mark the center point of the tweeter location. Step 3: If using a hole saw, first drill a pilot hole, then cut out the hole using a standard 2-1/8" hole saw. Step 4: If not using a hole saw, use either the cardboard packaging for the tweeters or the surface mount trim ring as a templa
Resumo do conteúdo contido na página número 9
Step 8:Screw the bolts in until the tweeter housing is firmly mounted to the panel. (Make sure the arrow at the rear of the tweeter housing is pointing in the desired direction.) Step 9: Insert the tweeter into the housing and attach trim ring. INSTALLING THE CROSSOVER Step 1: Find a location for the crossover away from any factory or aftermarket electrical wires. It is recommended to mount the passive crossover close to the amplifier. In the event you decide to upgrade and biamplify the system,
Resumo do conteúdo contido na página número 10
PC PASSIVE CROSSOVER (COVER REMOVED) Woofer To amplifier 0 -3 Tweeter 0,-3dB level switch SPECIFICATIONS Model PC 525S PC 650S Nominal Impedance 4 ohms 4 ohms Power 50/100 watts 60/120 watts Continuous/Peak Frequency Response 90 Hz–20kHz 90 Hz–20kHz Sensitivity 92 db 92 db (2.83v @ 1w/1m) Woofer 2-7/8” 2-15/16” Mounting Depth Woofer 4-3/4” 5-3/4” Mounting Diameter Tweeter 1-3/4” 1-3/4” Mounting Diameter 9
Resumo do conteúdo contido na página número 11
Warranty LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be defective in workmanship or material under normal use, for a period of two years from the date of purchase from the dealer as indicated by the date code marking of the product PROVIDED the product was installed by an authorized Directed dealer. During this two-year period, there will be no charge for this replacement PROVIDED the unit is return
