Resumo do conteúdo contido na página número 1
R9988
3 band Stereo PLL Synthesised
Personal Radio
Operating Instructions
ROBERTS
Resumo do conteúdo contido na página número 2
Contents Contents ..........................................................................................1 Controls ......................................................................................... 2-5 Display ............................................................................................6 Battery .............................................................................................7 Lock switch ......................................................................
Resumo do conteúdo contido na página número 3
Controls 1 2 3 4 Front 5 1. Memo button 3. Tuning + button 2. Waveband button 4. Tuning - button 5. Loudspeaker If you need any further advice, please call our Technical Helpline on :- 2 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 4
Controls Left side Right side 7 6 8 6. Stereo/Mono/Speaker switch 7. Recall button 8. Deep bass boost button 3
Resumo do conteúdo contido na página número 5
Controls Rear 9 10 11 9. Lock switch 10. Belt clip attachment point 11. Battery compartments If you need any further advice, please call our Technical Helpline on :- 4 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 6
Controls Top 12 13 14 12. Headphone socket 13. Volume control 14. Power button 5
Resumo do conteúdo contido na página número 7
Display BC D A E H G F A. Waveband indicator E. Frequency indicators B. Auto power off indicator F. Battery indicator C. Stereo indicator G. Lock indicator D. Preset indicator H. Deep bass boost indicator If you need any further advice, please call our Technical Helpline on :- 6 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 8
Battery 1. Open the battery covers located on the rear of your radio by sliding in the direction shown by the arrows. 2. Insert two LR03 (AAA) size batteries, one in each compartment. Ensure that batteries are inserted in accordance with the diagram shown on the rear of your radio. 3. Close the battery cover 4. Batteries should be replaced when the low battery indicator appears in the display. 5. Battery replacement should be completed within three minutes to prevent loss of stations stored
Resumo do conteúdo contido na página número 9
If you need any further advice, please call our Technical Helpline on :- 8 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 10
Lock switch The Lock switch is used to prevent unintentional operation of your radio. 1. Set the Lock switch located on the rear of your radio to the ‘Lock’ position . The power and all other buttons will be disabled. This will prevent accidental operation when your radio is packed in a suitcase or travel bag . 2. To prevent accidental operation of the controls when your radio is switched on, set the Lock switch to the up ‘Lock’ position. The symbol will appear in the display . 3. To release th
Resumo do conteúdo contido na página número 11
If you need any further advice, please call our Technical Helpline on :- 10 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 12
Aerials The lead connecting earphones to your radio acts as an FM aerial when plugged into the earphone socket. The lead should be extended as much as possible to increase FM reception. There is a separate directional aerial built into the radio for MW and LW reception. To achieve the best MW/LW reception, it may be necessary to rotate the radio. Loudspeaker On/Off switch & Earphones Your radio may be operated using the built in loudspeaker or the earphones supplied. 1. The built in loudspeaker
Resumo do conteúdo contido na página número 13
If you need any further advice, please call our Technical Helpline on :- 12 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 14
Scan tuning 1. Switch on your radio by pressing the Power button . 2. Select the required waveband by pressing the Band button. 3. Press and hold down either the Tuning + or - buttons until the frequency in the display begins to change rapidly. Release the button. Your radio will scan the selected waveband and stop automatically when it finds a station of sufficient strength. 4. Adjust the Volume control to the required setting. 5. Press and hold down either the Tuning + or - buttons for more t
Resumo do conteúdo contido na página número 15
If you need any further advice, please call our Technical Helpline on :- 14 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 16
Presetting stations There are 10 preset memories on each waveband giving a total of 30 preset memories. 1. Switch on your radio by pressing the Power button. 2. Select the required waveband by pressing the Band button . 3. Tune into the required station using one of the tuning methods previously described. 4. Press the Memo button, M and the preset number will flash. 5. Select the required preset number using the Tuning + or - buttons. 6. Press the Memo button to complete setting of the memory
Resumo do conteúdo contido na página número 17
If you need any further advice, please call our Technical Helpline on :- 16 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 18
Recalling a preset station 1. Switch on your radio by pressing the Power button. 2. Select the required waveband by pressing the Band button . 3. Press the Recall button, the preset number will flash. 4. Select the required preset number using the Tuning + or - buttons. 5. Press the Recall button to complete selection of the preset . 17
Resumo do conteúdo contido na página número 19
If you need any further advice, please call our Technical Helpline on :- 18 020 8758 0338 (Mon-Fri)
Resumo do conteúdo contido na página número 20
Mono mode (FM only) 1. If a station being received is weak some hiss may be audible. To reduce the hiss slide the Stereo/Mono/Speaker switch to the “Mono“ position. The stereo indicator will be removed from the display. Deep Bass Boost switch 1. Pressing the DBB button will enhance bass sounds. The display will show . Press the DBB button again to switch off the DBB function. The symbol will be removed from the display. Note: It is recommended for best results that the DBB function is used on
