Resumo do conteúdo contido na página número 1
EM316-2SFP
Transparent SFP-to-SFP Converter
With EM316NM or EM316LNXNM-OT Management
User Guide
PN 1259003-001
Revision C3
October 30, 2007
Resumo do conteúdo contido na página número 2
EM316-2SFP User Guide Table of Contents 1 Preliminary Considerations.............................................................................................................iv 1.1 Trademarks..................................................................................................................................iv 1.2 Copyright .....................................................................................................................................iv 1.3 Cu
Resumo do conteúdo contido na página número 3
EM316-2SFP User Guide 4 Module Management .......................................................................................................................13 4.1 Remote Command Line Interface (CLI) Setup ...........................................................................14 4.2 Serial Command Line Interface (CLI) Setup...............................................................................14 4.2.1 EM316NM Serial Console Setup ....................................
Resumo do conteúdo contido na página número 4
EM316-2SFP User Guide Table of Figures Figure 1 -- Unpacking ...........................................................................................................................3 Figure 2 -- Front Panel Schematic of the EM316-2SFP .......................................................................4 Figure 3 -- LED Legend ........................................................................................................................4 Figure 4 –
Resumo do conteúdo contido na página número 5
EM316-2SFP User Guide 1 Preliminary Considerations 1.1 Trademarks All trademarks are the property of their respective holders. 1.2 Copyright MRV Communications reserves the right to make changes to products and documentation without notice in order to improve reliability, function, or design. The user assumes sole responsibility for applying the information supplied herein. Copyright © 2007 MRV Communications. All rights reserved. 1.3 Customer Support Before con
Resumo do conteúdo contido na página número 6
EM316-2SFP User Guide 1.4 MRV Regulatory Compliance Contact your sales representative for more regulatory compliance information regarding specific MRV products or product families. Fiber Driver Chassis FCC Part 15 (Class A); IC (Class A); EMC Directive: Emission (Class A) and Immunity; LVD Directive: Electrical Safety; CE Marking; TUV CUE Mark (Canada, USA, EU); GOST; RoHS Directive, WEEE Directive: Wheelie Bin Mark; ETSI, NEBS, C-Tick Fiber Driver Modules FCC Part 15 (
Resumo do conteúdo contido na página número 7
EM316-2SFP User Guide 1.5 General Safety 1.5.1 Cautions and Warnings Disconnect all power from electronic devices before servicing. Some equipment may have multiple power cords requiring disconnection. 1.5.2 Laser Safety WARNING: Fiber optic equipment may emit laser or infrared light that can injure your eyes. Never look into an optical fiber or connector port. Always assume that fiber optic cables are connected to a laser light source. CAUTION: Do not install or termina
Resumo do conteúdo contido na página número 8
EM316-2SFP User Guide 1.5.3 Static Electricity Eliminate static electricity in the workplace by grounding operators, equipment, and devices including components and computer boards. Grounding prevents static charge buildup and electrostatic potential differences. Transporting products in special electrostatic shielding packages reduces electrical field damage potential. 1.5.4 Workplace Preparation A safe and effective workplace provides the following items. • ESD pr
Resumo do conteúdo contido na página número 9
EM316-2SFP User Guide 1.6 Specific Document Information Document Number: P/N 1259003-001 Rev C3 Document: EM316-2SFP User Guide Release Date: October 30, 2007 12:24:44 PM 1.7 Latest Revision and Related Documents The latest revision of MRV documents may be found at http://www.mrv.com. Release Notes for Fiber Driver products are produced as required. MegaVision User Guide: Describes management of Fiber Driver modules and other MRV ® Communications SN
Resumo do conteúdo contido na página número 10
EM316-2SFP User Guide 2 Product Overview The EM316-2SFP transparent converter contains two MSA compliant SFP sockets connected back- to-back. No components on the EM316-2SFP board are connected to the data path, so the module is considered transparent. Supported speed ratings range from 100 Mbps up to 2.7 Gbps where speed- matching or multi-rate SFPs are required in both ports. This EM316-2SFP converter is hot-pluggable, and it is managed through the Fiber Driver management bus fro
Resumo do conteúdo contido na página número 11
EM316-2SFP User Guide 2.1.2 Loopback The EM316-2SFP module supports loopback either by DIP switch setting or controlled through the CLI or SNMP software settings. For software control the Loopback DIP switch must be set to OFF. It the Loopback switch is ON, it cannot be over-ridden by software. Loopback is one way to assure that the fiber optical communication path is valid and error free. Packets sent over a short-circuit link should be received by the sender without any
Resumo do conteúdo contido na página número 12
EM316-2SFP User Guide 3 Preparation and Installation 3.1 Unpacking the Fiber Driver Module Follow the steps below as illustrated in the figure. Step 1. Open the cardboard box. Step 2. Remove the static bag containing the device. Step 3. Check for additional accessories in the box that may move beneath the module tray during transit. In the unlikely event that anything is missing, contact your authorized dealer or representative. If it becomes necessary to return the
Resumo do conteúdo contido na página número 13
EM316-2SFP User Guide 3.2 Front Panel Description Figure 2 -- Front Panel Schematic of the EM316-2SFP The EM316-2SFP module is equipped with the following interfaces: Port 1 (P1): SFP port rated 100 Mbps to 2.7 Gigabit depending on SFP interface Port 2 (P2): SFP port rated 100 Mbps to 2.7 Gigabit depending on SFP interface Cable Lengths The maximum cable length for SFP links is dependent upon the optical characteristic of the SFP transceivers only. The EM316-2SF
Resumo do conteúdo contido na página número 14
EM316-2SFP User Guide 3.3 DIP Switch Configuration The EM316-2SFP factory default configuration is designed to operate in the most common applications. Network Management = Enabled LIN = Disabled Loopback = Disabled The default configuration optimizes the EM316-2SFP module in most applications. Network management configuration does not override hardware DIP switch settings. These settings can only be changed using the DIP switches (SW1) on the EM316-2SFP module, regardless
Resumo do conteúdo contido na página número 15
EM316-2SFP User Guide 3.4 Module Installation EM316xx cards are hot-swappable, and they are designed to insert into a powered Fiber Driver chassis. Install the EM316xx module into a single slot or multiple slot chassis by aligning the edge of the card with the rail of the chassis and hand-tighten the thumb screw. The thumb screw points to the left in the BU-1, BU-2, BU-3, and BU-4 chassis. The thumb screw points to the bottom in the BU-16 chassis. Tools • 6-inch Phillips
Resumo do conteúdo contido na página número 16
EM316-2SFP User Guide Step 2. Install the module inside a Fiber Driver chassis by aligning the edge of the card with the rail of the chassis. Tighten the thumbscrew by hand. Figure 7 -- Module installation (not all chassis are shown) Handle the module by the edges to avoid damaging any components. Follow all ESD precautions listed at the front of this manual. Use your thumb to push the module securely into the chassis slot. Do not use excessive force, but make s
Resumo do conteúdo contido na página número 17
EM316-2SFP User Guide 3.5 Small Form Pluggables (SFP): Handling and Installation The EM316-2SFP accepts any SFP that complies with the MSA standard. Use MRV components for guaranteed results. Follow all ESD precautions listed at the front of this manual. 3.5.1 Cleaning Fibers Fiber optic components and cables are very sensitive to dirt, dust and mishandling, especially in high- speed networks. Dirty or mistreated fiber may cause errors and an unwanted degradation of signal qua
Resumo do conteúdo contido na página número 18
EM316-2SFP User Guide 3.5.2 Working with SFPs The pluggable optics modules used in the EM316xx products are extremely portable, and consequently may be easily mistreated. If SFPs are not protected against dust, remove the dust caps and clean them with 1.25 millimeter cleaners. Figure 11 -- SFP cleaners 3.5.2.1 Cleaning SFPs (1) Requirements: SFP to be cleaned 1.25 mm cleaners (2) Procedure: • Insert the 1.25mm cleaner into the SFP • Turn ¼ turn • Remove
Resumo do conteúdo contido na página número 19
EM316-2SFP User Guide 3.5.2.2 Mylar Tab SFP Modules The Mylar tab or nail latch on the module has a tab that you must pull in order to remove the module from a switching module port. Figure 12 -- Mylar Tab on SFP Module (3) Inserting a Mylar Tab SFP Module To insert the Mylar tab SFP module into a switching module port, line up the SFP module with the port, and slide it into place Figure 13 -- Insertion of a Mylar Tab SFP Module (4) Removing a Mylar Tab SFP Modul
Resumo do conteúdo contido na página número 20
EM316-2SFP User Guide 3.5.2.3 Actuator/Button SFP Modules The actuator/button SFP module has a button that you must push in order to remove the SFP module from a switching module port. Figure 15 – Actuator/Button SFP Module 3.5.2.4 Inserting an Actuator/Button SFP Module To insert the actuator/button SFP module into a switching module port, line up the SFP module with the port and slide it in until the actuator/button clicks into place. Be sure not to press the actuato
