Resumo do conteúdo contido na página número 1
PS536GS P/N 50236
Gas November 18, 2008 Rev.E
Domestic, Std. Export & CE Price $30.00
ENGLISH/French/Spanish
PS536GS Gas Ovens
Models: Combinations:
• PS536GS Gas • Single Oven
• Double Oven (Two-Stack)
• Triple Oven (Three-Stack)
OWNER'S OPERATING, INSTALLATION,
AND PARTS MANUAL
for domestic, standard export and CE export ovens
© 2003 Middleby Marshall, Inc.
is a registered trademark of Middleby Marshall, Inc. All rights reserved.
Middleby Cooking Systems Group • 1400 Toastmaster Drive •
Resumo do conteúdo contido na página número 2
ENGLISH NOTICE: This Owner's Operating and Installation Manual should be given to the user. The operator of the oven should be familiar with the functions and operation of the oven. This manual must be kept in a prominent, easily reachable location near the oven. Ovens are shipped from the factory configured for use with natural gas. If permitted by local, national and international codes, at the time of installation the oven may be converted to propane gas operation. This conversion requires
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS page page SECTION 1 - DESCRIPTION ................................................... 4 B. Connection ...................................................... 13 I. OVEN USES ............................................................. 4 V. GAS SUPPLY .......................................................... 14 II. OVEN COMPONENTS ............................................. 4 A. Gas Utility Rough-In Recommendations ....... 14 A. Window ........................................
Resumo do conteúdo contido na página número 4
ENGLISH SECTION 1 - DESCRIPTION J. Conveyor: Moves the food product through the oven. I. OVEN USES Not Shown: PS536GS ovens can be used to bake and/or cook a wide variety of food products, such as pizza, pizza-type products, K. Gas Burner: Heats air, which is then projected to the air cookies, sandwiches and others. fingers by the blowers. L. Blowers: Fans that project hot air from the gas burner to II. OVEN COMPONENTS - see Figure 1-1. the air fingers. A. Window: Allows the user to see and
Resumo do conteúdo contido na página número 5
SECTION 1 - DESCRIPTION Table 1-3: Electrical specifications for gas ovens (per oven cavity) Main Blower Control Current Voltage Circuit Voltage Phase Freq. Draw Poles Wires 208/240V 120V conv. speed control 1 Ph 50/60 Hz 6A * 2 Pole 3 Wire (2 hot, 1 gnd) & drive motor; all others as per line (208/240V) * The current draw shown above is an average value for normal operation. The initial amperage draw on oven startup may exceed the listed value. Table 1-4: Gas orifice and pressure specificat
Resumo do conteúdo contido na página número 6
ENGLISH SECTION 2 - INSTALLATION WARNING - For gas ovens, after any conversions, readjustments, or service work on the oven: • Perform a gas leak test. • Test for correct air supply. • Test for proper combustion and gas supply. • Check that the ventilation system is in operation. WARNING Keep the appliance area free and clear of combustibles. WARNING The oven must be installed on an even (level) non-flammable flooring and any adjacent walls must be non-flammable. Recommended minimum clearances
Resumo do conteúdo contido na página número 7
SECTION 2 - INSTALLATION Figure 2-1 - Installation Kit 2 3 1 4a, 4b, 4c, 4d 8 12 16 14 13 15 6 11 5 10 7 9 I. INSTALLATION KIT - see Figure 2-1 Qty. Qty. Qty. Inc. with Inc. with Single Double Triple domestic CE Item Oven Oven Oven Part No. ovens? ovens? Description 1 1 1 1 48605 Yes Yes Top panel 2 4 4 4 3A80A8801 Yes Yes Screw, pan head #10 x 2″ 3 1 1 1 42893 Yes Yes Base pad 4a 4 4 -- 42890 Yes Yes 17-1/2″ (445mm) leg extension, for single and double ovens 4b -- 4 -- 45360 Yes Yes 20-1/2″ (52
Resumo do conteúdo contido na página número 8
ENGLISH SECTION 2 - INSTALLATION B. Recommendations II. VENTILATION SYSTEM NOTE THAT THE HOOD DIMENSIONS SHOWN IN FIGURE 2- 2 ARE RECOMMENDATIONS ONLY. LOCAL, NATIONAL AND INTERNATIONAL CODES MUST BE FOLLOWED WHEN IMPORTANT INSTALLING THE VENTILATION SYSTEM. ANY APPLICABLE Where national or local codes require the CODES SUPERSEDE THE RECOMMENDATIONS SHOWN IN THIS MANUAL. installation of fire suppression equip- ment or other supplementary equipment, The rate of air flow exhausted through the ve
Resumo do conteúdo contido na página número 9
SECTION 2 - INSTALLATION Figure 2-3 - Leg extension and casters installation III. ASSEMBLY A. Top Panel and Base Pad Assembly Finished sides of 1. Install the four leg extensions onto the base pad using the leg extension 3/8"-16x1" screws, 3/8" flat washers, and 3/8" lockwashers face corner of supplied in the Base Pad Kit. See Figure 2-3. Check that base pad the finished sides of each leg extension face OUTWARDS. 3/8" flat For domestic and standard export ovens: washer One rear leg should be a
Resumo do conteúdo contido na página número 10
ENGLISH SECTION 2 - INSTALLATION B. Stacking 1. Stack an oven cavity on top of the lower oven. Check the following: For single ovens, skip ahead to Part C, Restraint Cable • All four sides of the lower lip (on the bottom edge of the Installation. oven cavity) overlap the top of the lower oven. IMPORTANT • The oven is level. Middleby Marshall STRONGLY RECOMMENDS that PS536GS • The oven is firmly seated. oven cavities be stacked using the following: See Figure 2-6. • PS500 Series Stacking Lift Ki
Resumo do conteúdo contido na página número 11
SECTION 2 - INSTALLATION D. Conveyor Installation Figure 2-9 - Conveyor installation 1. Unfold the conveyor as shown in Figure 2-9. Then, begin to slide the conveyor into the end of the oven. The conveyor can only be installed from the end of the oven with the drive motor. Folded frame 2. Continue moving the conveyor into the oven until the frame protrudes equally from each end of the oven. Check that the crumb tray supports located on the underside of the con- veyor frame rest firmly against
Resumo do conteúdo contido na página número 12
ENGLISH SECTION 2 - INSTALLATION 5. If it is necessary to add or remove conveyor links to achieve E. Final Assembly the correct tension, OR if it is necessary to reverse the 6. Install the drive chain between the conveyor drive sprocket conveyor belt for correct orientation, the belt will need to be and the motor sprocket. To install the chain, it will be removed from the conveyor frame. If this is necessary, necessary to lift the drive end of the conveyor slightly. perform the following proce
Resumo do conteúdo contido na página número 13
SECTION 2 - INSTALLATION IV. ELECTRICAL SUPPLY WARNING The oven requires a ground connection to the oven ground Authorized supplier personnel normally accomplish screw located in the electrical junction box. (The box is shown the connections for the ventilation system, electric supply, in Figure 2-14.) The ground connection must comply with all and gas supply, as arranged by the customer. Following applicable local, national, and international codes. If necessary, these connections, the fact
Resumo do conteúdo contido na página número 14
ENGLISH SECTION 2 - INSTALLATION V. GAS SUPPLY Appliances, ANSI Z21.69 (in U.S.A.), as well as a quick-disconnect device that complies with the Standard for Quick-Disconnect CAUTION Devices for Use With Gas Fuel, ANSI Z21.41 (in U.S.A.). DURING PRESSURE TESTING NOTE THE FOLLOWING: C. Gas Conversion 1. The oven and its individual shutoff valve must be discon- Where permitted by local and national codes, it is possible to nected from the gas supply piping system during any convert ovens from natur
Resumo do conteúdo contido na página número 15
SECTION 2 - INSTALLATION ® Figure 2-16. Gas Burner Assembly 5. Disconnect electrical connection of the Moduplus . Gas Burner 6. Check minimum pressure setting and readjust if necessary. (See Adjusting Minimum Pressure Setting for proper adjusting procedure.) 7. Reconnect pressure feedback connection (if appcable). 8. If minimum and maximum pressures are set, wire the ® Moduplus in circuit. 9. Close pressure tap screw. F. Adjusting the Minimum Pressure Setting 1. Disconnect pressure feedback co
Resumo do conteúdo contido na página número 16
ENGLISH SECTION 2 - INSTALLATION NOTES 16
Resumo do conteúdo contido na página número 17
SECTION 3 - OPERATION E D B A C I. LOCATION AND DESCRIPTION OF CONTROLS "BLOWER" Switch: Turns the blowers and A. E. Digital Temperature Controller: Continuously cooling fans on and off. The HEAT Switch has monitors the oven temperature. Settings on the no effect unless the BLOWER Switch is in the Digital Temperture Controller control the activa- “ON” position. tion of the burner. Keypad controls allow the operator to select the cooking temperature and B. "HEAT" Switch: Allows the burner t
Resumo do conteúdo contido na página número 18
ENGLISH SECTION 3 - OPERATION 7. Wait for the oven to heat to the setpoint temperature. Higher II. NORMAL OPERATION - STEP-BY-STEP setpoint temperatures will require a longer wait. The oven A. DAILY STARTUP PROCEDURE can reach a temperature of 500°F (232°C) in approximately 5 minutes. 1. Check that the circuit breaker/fused disconnect is in the on position. Check that the window is closed. 8. (Optional) Press the Tem- perature ( ) key to show 2. Turn the "BLOWER" ( ) the Actual Temperature wa
Resumo do conteúdo contido na página número 19
SECTION 3 - OPERATION III. QUICK REFERENCE: DIGITAL TEMPERATURE CONTROLLER Display "HEAT ON" Shows the Set Point Light or the Actual Tem- Lights when the perature in degrees burner is in Fahrenheit (F) or operation. Celsius (C). "SP LOCK" Light Lights when the "SET PT" set point is locked out from changes. (setpoint) This setting can Light only be changed by Lights when the service personnel. set point is shown in the display. OVERTEMP Light Lights when the oven "ACTUAL temperature is TEMP" L
Resumo do conteúdo contido na página número 20
ENGLISH SECTION 4 - MAINTENANCE WARNING Before ANY cleaning or servicing of the oven, perform the following procedure: 1. Switch off the oven and allow it to cool. Do NOT service the oven while it is warm. 2. Turn the full-flow gas safety valve to the off position. 3. Turn off the electric supply circuit breaker(s) and disconnect the electric supply to the oven. 4. If it is necessary to move a gas oven for cleaning or servicing, disconnect the gas supply before moving the oven. When all cleanin
