Resumo do conteúdo contido na página número 1
54Mbps Wireless Access Point w/bridge, inter-building
WAP-4030A
User’s Manual
Resumo do conteúdo contido na página número 2
Copyright Copyright © 2005 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET. PLANET makes no representations or warranties, either expressed or implied, with respect to the contents hereo
Resumo do conteúdo contido na página número 3
interference received, including interference that may cause undesired operation. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. R&TTE Compliance Statement This equipment complies with all
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS Chapter 1 Introduction ..................................................................................5 1.1 Package Contents.................................................................................................... 5 1.2 System Requirements.............................................................................................. 5 1.3 Features ................................................................................................................
Resumo do conteúdo contido na página número 5
Chapter 1 Introduction Thank you for purchasing WAP-4030A. The WAP-4030A supports both IEEE 802.11b and IEEE 802.11g standards. You can use it to connect an existing WLAN, or to build up a new wireless LAN. Except for essential AP mode, WAP-4030A also provides Repeater, Bridge, and Client modes to accommodate all kinds of network topology. High data rate (up to 54Mbps) support allows faster communication between LAN and WLAN. Maximize network efficiency while minimizing your network inves
Resumo do conteúdo contido na página número 6
Provide WPA-PSK, 64/128-bit WEP Encryption and MAC Filter to protect the wireless data transmissions Support Wireless AP / Client / Repeater and Bridge mode Support MAC Address Filter Support DHCP client for auto IP address assignment Provide a reverse-polarity SMA connector for external antenna connection Auto Fall-Back Data Rate for Long-Distance communication and noisy environment Web-based configuration 1.4 Specification Standard IEEE 802.11g / 802.11b Frequency Band 2.40
Resumo do conteúdo contido na página número 7
LED Indicators 3; PWR, WLAN, LAN Power 12V DC, 1A Temperature 0 ~ 55°C (Operating) Humidity 10 ~ 90%, non-condensing (Operating) Dimension 169 x 87 x 30 (mm) Weight 155g Emission FCC Class B, CE-mark 1.5 Wireless Performance The following information will help you utilizing the wireless performance and operating coverage of WAP-4030A. 1. Site selection To avoid interferences, please locate WAP-4030A and wireless client away from transformers, microwave ovens, heavy-duty motors, f
Resumo do conteúdo contido na página número 8
Chapter 2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about the WAP-4030A. 2.1 Hardware Connection 12V DC RESET ANT + LAN 1. Locate an optimum location for the WAP-4030A. The best place for your WAP-4030A is usually at the center of your wireless network, with line of sight to all of your mobile stations. 2. Assemble the antenna to WAP-4030A. Try to place them to a position that can best cover your wireless network.
Resumo do conteúdo contido na página número 9
Chapter 3 Configuring the Wireless AP Web configuration provides a user-friendly graphical user interface (web pages) to manage your WAP-4030A. An AP with an assigned IP address (e.g. http://192.168.0.1) will allow you to monitor and configure (via web browser e.g., MS Internet Explorer or Netscape). 1. Open your web browser. 2. Enter WAP-4030A IP address (default IP address is http://192.168.0.1) into the address field of the web browser. Please also make sure your PC’s IP address is in
Resumo do conteúdo contido na página número 10
3.1.1 Client Mode In this screen, you can configure WAP-4030A as a wireless client. It is used to let a network device with only wired Ethernet function to have wireless LAN communication capability. It provides both Ad-Hoc and Infrastructure modes for the “Client Mode”. With “Ad-Hoc mode”, it can let your network device join a wireless LAN with peer-to-peer communication. With “Infrastructure mode”, it can let your network device join a wireless LAN through an access point. 10
Resumo do conteúdo contido na página número 11
Parameter Description Station Mode 802.11b: It allows to select the transmit rate up to 11Mbps. Mixed: It allows to select the transmit rate up to 54Mbps. MAC Cloning Mode Disabled: It will use it’s own MAC address to access the wireless LAN. Enabled: It will use PC’s MAC address to access the wireless LAN. SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure t
Resumo do conteúdo contido na página número 12
Infrastructure: It can let your network device join a wireless LAN through an access point. Channel Select the appropriate channel from the list provided to correspond with your network settings. Channels differ from country to country. Channel 1-11 (North America) Channel 1-14 (Japan) Channel 1-13 (Europe) Security Disable: Disable the security function. WEP: It is an authentication algorithm, which protects authorized Wireless LAN users against eavesdropping. The Authentication type
Resumo do conteúdo contido na página número 13
Parameter Description Mode 802.11b mode: It allows to select the transmit rate up to 11Mbps 802.11g mode: It allows to select the transmit rate up to 54Mbps Mixed mode: It provides best performance for 11g transmission when you enable the AP mode selection to “Mixed mode”. SSID The SSID (up to 32 printable ASCII characters) is the unique name identified in a WLAN. The ID prevents the unintentional merging of two co-located WLANs. Please make sure that the SSID of all stations in the sa
Resumo do conteúdo contido na página número 14
securely. You may refer to section 3.5 to know the detail settings of it. WPA: You can use a pre-shared key to authenticate wireless stations and encrypt data during communication. You may refer to section 3.6 to know the settings of it. Advance setting It provides more powerful features for you to configuring. Access Filter This Access Point allows you to provide a Filter List of MAC addresses that are allowed associating with this AP. Please click “Apply” button to save the above configu
Resumo do conteúdo contido na página número 15
and multicast messages. Protection Mode It provides best performance for 11g transmission when you enable it. Transmit Rate When you enable the station mode selection to “802.11b” and it allows you to select the speed of 1-11Mbps. When you enable the station mode selection to “802.11g” and it allows you to select the speed of 1-54Mbps. Preamble Type Preamble type defines the length of preamble block in the frames during the wireless communication. Auto: It will auto switch to the more s
Resumo do conteúdo contido na página número 16
3.1.2.2 Access Filter This Access Point allows you to provide a Filter List of MAC addresses that are allowed/denied associating with this AP. Parameter Description MAC Filtering You can enable or disable the MAC Filtering function. Filter Mode If you select “Only deny PCs with MAC listed below to access this device”, then all the PCs in the list will be denied to access and all other PCs will be allowed to access. If you select “Only allow PCs with MAC listed below to access this de
Resumo do conteúdo contido na página número 17
3.1.3 Repeater Mode In this mode, WAP-4030A can be a repeater between Access Point and wireless clients, that can extend the connect distance of your Access Point. When it works in this mode, it will also work as an access point. WAP-4030A has provided two repeater modes, you may select the suit one to your wireless network. Parameter Description Repeater Type WAP-4030A has support two type of Repeater mode - WDS Repeater and Universal Repeater. When different Repeater mode selected
Resumo do conteúdo contido na página número 18
be 50% as the clients connect to AP directly. When clients connect to second WDS Repeater, the performance will be 25%. Universal Repeater: This repeater mode will connect your WAP-4030A to the Access Point when the SSID and channel are the same. You will need to enter remote AP's SSID to Parent SSID field and set the Channel the same as your Access Point. The Repeater mode configuration is include two parts. The upper part is use to show which device the WAP-4030A will connect. The lo
Resumo do conteúdo contido na página número 19
access point easily. If you are building a public wireless network, enabling this feature is recommended. Disabling "Response to Broadcast ESSID requests" can provide better security. Security Disable: Disable the security function. WEP: WEP is an authentication algorithm, which protects authorized Wireless LAN users against eavesdropping. The Authentication type and WEP key of wireless stations must be the same with the Access Point. This Access Point supports 64/128-bit WEP Encryption
Resumo do conteúdo contido na página número 20
Parameter Description AP MAC Address You have to enter the MAC addresses of another WAP-4030A that it will connect to. Mode 802.11b mode: It allows to select the transmit rate up to 11Mbps 802.11g mode: It allows to select the transmit rate up to 54Mbps Mixed mode: It provides best performance for 11g transmission when you enable the AP mode selection to “Mixed mode”. Channel Please select the same channel on both WAP-4030A. Security Disable: Disable the security function. WEP: WEP
