Resumo do conteúdo contido na página número 1
Resumo do conteúdo contido na página número 2
Contents Chapter 1: Introduction .................................................................................................. 3 The NetComm 11G 54Mbps Wireless Access Point ...................................... 3 Chapter 2: Planning Your Wireless Network ................................................................ 4 Network Topology ............................................................................................ 4 Roaming ...................................................
Resumo do conteúdo contido na página número 3
Chapter 1: Introduction The NetComm 11G 54Mbps Wireless Access Point Congratulations on your purchase of the Netcomm 11G 54Mbps Wireless Access Point (AP). This product is designed specifically for high-speed wireless LAN environment needs. It is easy to configure and operate even for non-technical users. Instructions for installing and configuring this product are included in this manual. Before you install and use this product, please read the manual carefully so you may take full advantage of
Resumo do conteúdo contido na página número 4
Chapter 2: Planning Your Wireless Network Network Topology A wireless LAN is a group of computers, each equipped with one Instant Wireless Series adapter. Computers in a wireless LAN must be configured to share the same radio channel. The Instant Wireless Series adapters provide access to a wired LAN for wireless workstations. An integrated wireless and wired LAN is called an infrastructure configuration. A group of Instant Wireless Series adapter users and an Instant Wireless 11g Wireless Acc
Resumo do conteúdo contido na página número 5
How to Make Your Wireless Network More Secure Wireless networks can be vulnerable to an outsider gaining access if the encryption settings are not set adequately. Some of the default security settings on some wireless hardware, and in Microsoft Windows, may allow access to your wireless network from other wireless devices. The concepts that are presented here are offered only as a guide, and may help make your wireless network more difficult for an outsider to gain access. For more specific info
Resumo do conteúdo contido na página número 6
Chapter 3: Your NetComm 11G Wireless AP The Back Panel Antenna Connection INIT Button Selection Switch LAN Cable Power Input Antenna Connection Please install the external dipole antenna directly into the reversed SMA connector of AP. After the AP starts to work, you may adjust the angle of the antenna or reposition the AP to get a better performance and reach. INIT Button “INIT” means “Initiation”. While pressing the button, the AP will reboot and ERASE all current settings, and restore to fact
Resumo do conteúdo contido na página número 7
The Front Panel LED Color Status Description Power Green ON The AP power on OFF The AP power off DIAG Green ON 1) The AP is in normal operation mode 2) While in firmware upgrade process, it indicates the AP is writing the firmware into Flash ROM Blinking 1) The AP is in self-diagnostic mode. 2) While in firmware upgrade process, it indicates the AP is waiting the Wireless Navigator sending firmware image OFF 1) The AP starts to boot up the system. 2) While in firmware upgrade process, it indicat
Resumo do conteúdo contido na página número 8
Chapter 4: Connecting the Wireless AP Before continuing, please ensure you have the following package contents ready for the hardware installation. Package Contents One Wireless Access Point One External Antenna with Reversed SMA Connector One UTP straight LAN Cable (RJ-45 connector) One Power Adapter One CD-ROM (Wireless Navigator utility software & user’s manual included) One User Guide Hardware Installation Following illustration is an example showing how to install AP with hub/sw
Resumo do conteúdo contido na página número 9
1. Find an optimum location for the Access Point. The best place for the Access Point is usually at the center of your wireless network, with line of sight to all of your mobile stations. Placing the unit in the celing is ideal. 2. Fix the direction of the antenna. Try to place it in a position which can best cover your wireless network. Normally, the higher you place the antenna, the better the performance will be. The antenna's position enhances the receiving sensitivity. 3. Connect a standar
Resumo do conteúdo contido na página número 10
Chapter 5: Setting Up the Wireless Access Point Connecting the AP to your Network For optimal performance, usually the center of your wireless network is the best place for your AP, with line of sight to all of your mobile stations. Try to place it in a position where can best cover your wireless network and is away from any potential source of interference. And normally, the higher you place the AP, the better the wireless signal coverage will be. The following picture describes how to use the
Resumo do conteúdo contido na página número 11
TCP/IP Setup for Windows 98 and Millennium 1. Click the Start button, select Settings, and open the Control Panel. Inside the Control Panel, double-click the Network icon. 2. If the TCP/IP Protocol is listed for your network adapter, go to step five. Otherwise, click the Add button. 3. When the Component Type window appears, select Protocol and click the Add button. 4. Select Microsoft in the Manufacturers list and choose TCP/IP in the Network Protocols list. Then, click the OK button. 5. When t
Resumo do conteúdo contido na página número 12
TCP/IP Setup for Windows 2000 1. At the Windows 2000 desktop, right click My Network Places and select Properties. Then, right click Local Area Connection. Choose Properties. 2. If the TCP/IP Protocol is listed for your network adapter, go to step five. Otherwise, click the Install button. 3. When the Component Type window appears, select Protocol, and click the Add button. 4. Select Internet Protocol (TCP/IP) from the list and click the OK button. 5. When the Local Area Connection Properties w
Resumo do conteúdo contido na página número 13
Installing the Wireless Navigator The Wireless Navigator Utility is provided to allow user(s) easily to configure the AP through any Windows-based PC over wired or wireless LAN port. This section describes procedures for installing the Wireless Navigator Utility to PC. 1. Insert the installation CD-ROM into the CD-ROM drive. Run SETUP.EXE program on the CD-ROM. 2. After the InstallShield Wizard preparation has completed finished, the Install Shield window will be shown. Click the Next button to
Resumo do conteúdo contido na página número 14
Startup and Login Follow the procedures below to startup Wireless Navigator and find the AP. Before you start the following procedure, please connect the Ethernet cable, connect the power cord, and then turn on the AP. All wireless clients should be requested to set the their SSIDs to the same as the AP SSID in advance before continuing. 1. Refer to previous section "Install the Wireless Navigator to your PC" in order to startup the configuration. 2. Click Start and select Programs, Wireless Nav
Resumo do conteúdo contido na página número 15
Configuring the Access Point The Wireless Navigator includes nine tabs to help you customise your Access Point settings to fit your Network: the Info tab the Assoc tab the Wireless tab the Access tab the Advanced tab the Security tab the IP Address tab the Admin tab the Help tab Rev. 1 - YML668 www.netcomm.com.au NP5400 11g Wireless Access Point User Guide Page 15
Resumo do conteúdo contido na página número 16
The Info Tab The Info Tab displays the current AP settings. Access Point Information Access point name: Displays current device name of the AP. You also can change the name. MAC address of AP: Displays the unique fMAC number burned into this AP that identifies itself from other Ethernet devices Associated stations: Displays the number of wireless client devices associated with this AP. Wireless Firmware version: Displays the version number of wireless LAN firmware embedded in this AP. AP version
Resumo do conteúdo contido na página número 17
The Assoc Tab The Assoc Tab displays all the wireless clients, which are currently associated with this AP. Mac address: Displays the list of the MAC address of associated wireless client.If you click the refresh button of your web browser, then the list will be updated. The Wireless Tab The Wireless Tab lets you select the network settings. Performance Mode: In Maximum interoperability mode, the AP will accept connections to both 802.11b and 802.11g client devices. In Maximum performance mode,
Resumo do conteúdo contido na página número 18
The Access Tab The Access Tab allows you to set the filter to specific wireless client device(s). Enable access control: If it is checked, the AP will start to filter any wireless client device with MAC address listed below. MAC address #: Please enter the MAC address of the wireless devices which need filtered in wireless LAN network. The device with same MAC address listed will not be able to associate with this AP. Note: Click button "Save" to store the settings. The settings will work after
Resumo do conteúdo contido na página número 19
The Security Tab The Security Tab displays 802.11b/g security and encryption options on this AP. WEP configuration: Display the Wired Equivalent Privacy security configurations Enable WEP: Enables the Wired Equivalent Privacy security function. WEP key length: Selects 64-bit or 128-bit WEP encryption. Be sure that the key length setting in the AP shall be the same as in wireless clients, or the communication will not work. WEP key: For 64-bit WEP encryption, a key of 10 hexadecimal characters in
Resumo do conteúdo contido na página número 20
The IP Address Tab The IP Address Tab displays IP settings options on this AP. IP Address Mode: Select "Static" or "DHCP" mode. For "Static" mode, the IP address settings are given by user. For "DHCP" mode, these settings will be overridden by a DHCP server on your network. The default setting is "Static" Default IP Address: The static IP address you want to assign to the AP. The default value is "192.168.1.100". Default subnet mask: The subnet mask you want to assign for the AP. The default val
