Manual do usuário Black Box LE180A

Resumo do conteúdo contido na página número 1

NETWORK SERVICES
LE180A 10Base-T Transceiver
• Stand-Alone model
• Attached Unit Interface (AUI) to
Ethernet RJ-45 connectors
No external power requirement
The LE180A transceiver is a media access unit
(MAU) that connects the AUI port of data
terminal equipment, repeaters, or other
network devices either directly or through an
AUI cable to an Ethernet 10BASE-T device. The Ethernet device is connected to the
transceiver through an unshielded or shielded twisted-pair copper cable with RJ-45
conne

Resumo do conteúdo contido na página número 2

LE180A LE180A General Description LE180A Features • Provides a complete interface of the AUI to Ethernet UTP cable. The LE180A IEEE802.3 compliant Ethernet transceiver uses 10Mbps Ethernet CSMA/CD protocol to provide a connection interface to 10Base-T Ethernet unshielded • Supports 10Mbps data transfer rates. twisted-pair (UTP) cables. The transceiver connects to the AUI connector of an • Supports Carrier Sense Multiple Access/Collision Detection (CSMA/CD) contention Ethernet device via standard

Resumo do conteúdo contido na página número 3

LE180A LE180A Connectors & Cables -- Continued Connectors & Cables -- continued AUI connector -- continued UTP cable (RJ-45 connector) -- continued Table 1: AUI Male Connector Pinouts Table 2: RJ-45 Pin Assignments Pin Name Pairs Use Pin Out Jack Assignments 3 DO + Transmit Data Out + 1 Outgoing Data 1 (+) 10 DO - Pair Data Out - 2 Outgoing Data 2 (-) 11 DO S Data Out Shield 3 Incoming Data 1 (+) 5 DI + Receive Data In + 4 Not connected 12 DI - Pair Data In - 5 Not connected 4 DI S Data In Sh

Resumo do conteúdo contido na página número 4

LE180A LE180A Installation -- Continued Installation Connecting to a Device AUI port Switches The LE180A can connect to any Ethernet device with an AUI port. To connect to a The LE180A has a 3-position DIP switch. See Figure 6. Two of the switches provide device with an AUI port, an AUI cable or direct connection is required. See Figure 7. options for enabling and disabling the SQE test and LINK test functions. Both test functions are Ethernet and 10Base-T standards. SW2 SW1 SW3 AUI Cable Lengt

Resumo do conteúdo contido na página número 5

LE180A LE180A Operations Technical Specifications For use with Black Box Model LE180A or equivalent. LEDs Standards IEEE 802.3ab, IEEE 802.3 Figure 9 shows the LE180A LEDs: Data Rate 10 Mb/s Status Receive Dimensions 1.77" x 0.81” x 3.14" (44.96 mm x 20.57mm x 79.76mm) Weight 0.2 lbs. (90.72 g) approximately Power Consumption 500mA @ 12VDC Power Source AUI port Operating Temp 0 to 50°C (32°F to 122°F ) Storage Temp: -25 to 85°C (-13°F to 185°F ) Humidity: 5 to 95%, non-condensing Collision

Resumo do conteúdo contido na página número 6

LE180A LE180A Cable Specifications Contact Us The physical characteristics of the media cable must meet or exceed IEEE 802.3 Black Box, Headquarters specifications. 1000 Park Drive Lawrence, PA 15055-1018 Copper cables By Telephone: 877-877-2269 Category 3: (minimum requirement) Gauge 24 to 22 AWG By Fax: 724-746-0746 Attenuation 11.5 dB/100m @ 5-10 MHz By E-mail: info@blackbox.com Maximum cable distance: 100 m Category 5: (recommended) Technical Support Gauge 24 to 22 AWG Attenuation 22.0

Resumo do conteúdo contido na página número 7

LE180A Compliance Information CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful