Resumo do conteúdo contido na página número 7
5 Follow voice prompts to connect your phone to your headset. When your headset successfully pairs with your phone, you hear “pairing complete”. When connected, you hear “phone 1 connected” and see the indicator light rapidly flash in blue and purple. To connect to both phones, simply turn on the first phone while the second phone is connected. When you hear “phone 2 connected” , your headset is connected to both phones. The last paired phone (your second phone) is now your primary pho
Resumo do conteúdo contido na página número 8
test your connection 1 Place the headset over your ear. 2 On one phone, dial a number and press the Call/Send key. Repeat for the second phone. If your phones and headset are successfully connected, you hear ringing on the headset. For daily use, make sure your headset is turned on, and your phone’s Bluetooth feature is on. Your headset and phone will connect automatically. 6 pair & connect
Resumo do conteúdo contido na página número 9
turn on & off turn on Open the headset boom. The indicator light flashes blue three times, then flashes in blue and purple (if connected with a device) or is steadily blue (if ready to be paired). turn off Close the headset boom. The indicator light flashes three times then turns off. turn on & off 7
Resumo do conteúdo contido na página número 10
put it on You can wear your headset using either an earhook or ear cushion. wear with earhook 1 Remove and install all the supplied earhooks to find a good fit. 2 Your headset comes ready for your right ear. To change for your left ear: 1 2 From Right Ear To Left Ear 8 put it on
Resumo do conteúdo contido na página número 11
3 Flex the earhook and loop it over your ear. wear with ear cushion 1 Remove earhook from headset. put it on 9
Resumo do conteúdo contido na página número 12
2 Try out all the supplied ear cushions to get a good fit. 10 put it on
Resumo do conteúdo contido na página número 13
battery check Press both Volume Up and Volume Down buttons while not on a call. indicator voice talk time light prompt red “battery less than 1.5 hours level is low” yellow “battery between 1.5 to 3.5 hours level is medium” green “battery more than 3.5 hours level is high” To save battery power, turn off the headset when you don’t use it for an extended time by closing the boom. battery check 11
Resumo do conteúdo contido na página número 14
calls To... answer call Press the Call button. reject call Press and hold a Volume button until you hear an audio tone make a voice Press the Call button and you dial call hear an audio tone. redial last call Press and hold the Call button until you hear an audio tone. mute or Press and hold both Volume Up unmute a call and Volume Down buttons until you hear “mute on” or “mute off”. end a call Press the Call button. answer Press the Call button. second incoming call 12 calls
Resumo do conteúdo contido na página número 15
To... reject Press and hold a Volume button second until you hear a tone. incoming call Tip: When connected to two phones, voice prompts help manage call functions such as voice dial, redial, and end call. Follow the voice prompts to execute a function on the desired phone. Note: Your headset supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See the instructions that came with your phone. Note: Some call features are pho
Resumo do conteúdo contido na página número 16
status indicators indicator light (with charger plugged in) headset headset status indicator red charging (battery level less than 50% charge) yellow charging (battery level more than 50% charge) green charging complete 14 status indicators
Resumo do conteúdo contido na página número 17
indicator light (with charger not plugged in) headset headset status indicator off power off three blue powering on/off flashes steady pairing/connect mode blue rapid blue/ connection successful purple flashes quick blue incoming/outgoing call on flash phone 1 status indicators 15
Resumo do conteúdo contido na página número 18
headset headset status indicator quick incoming/outgoing call on purple phone 2 flash slow blue connected (on a call) pulse slow blue standby (connected to one phone) flash slow standby (connected to two green phones) flash slow red idle (not connected to a phone) flash 16 status indicators
Resumo do conteúdo contido na página número 19
headset headset status indicator slow connected call muted purple pulse steady red attempting to connect quick red low battery flash Note: After 1 minute on a call or 20 minutes of inactivity, the light stops flashing to conserve power, but the headset remains on. status indicators 17
Resumo do conteúdo contido na página número 20
tips & tricks enable/disable voice prompts With the headset turned on, press and hold either Volume button and Call button until you hear “voice prompts on” or “voice prompts off”. restore to factory settings Caution: This action erases all pairing information stored in your headset. To restore your headset to original factory settings, with the headset turned on, press and hold both the Volume Up and Volume Down buttons and Call button for 10 seconds until you hear “welcome to the Motoro
Resumo do conteúdo contido na página número 1
motorola H17
Quick Start Guide
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
your headset Take a moment to familiarize yourself with your new H17 Headset. Earhook Volume Up Indicator Button Light Volume Down Ear Button Speaker Boom Charging Port Call Microphones Button your headset 1
Resumo do conteúdo contido na página número 4
charge it You’ll need to charge your headset before using it. Close the boom and plug the charger into the charging port on your headset and a wall outlet. The indicator light is red or yellow while the battery is charging. When the battery is fully charged, the indicator light turns green. Note: Headset is not functional while charging. Note: Your battery is designed to last the life of your product. It should only be removed by a recycling facility. Any attempt to remove or replace your
Resumo do conteúdo contido na página número 5
pair & connect Let’s get your headset paired and connected to your Bluetooth phone(s). pair & connect first phone 1 Turn off any Bluetooth devices previously paired (linked) with your headset. 2 Turn on the Bluetooth feature on your phone. 3 Turn on your headset and put headset on your ear (see “turn on” on page 7 and “put it on” on page 8 for help). The indicator light becomes steadily lit in blue and you hear “ready to pair”. 4 Follow voice prompts to connect your phone to your headse
Resumo do conteúdo contido na página número 6
When your headset successfully pairs with your phone, you hear “pairing complete”. When connected, you hear “phone 1 connected” and see the indicator light rapidly flash in blue and purple. pair & connect second phone (optional) 1 Turn off first phone and any other Bluetooth devices previously paired with your headset. 2 Turn your headset off by closing boom. 3 Turn on the Bluetooth feature on your phone. 4 Turn on your headset by opening boom and put headset on your ear. The indicator
