Resumo do conteúdo contido na página número 1
Raid SATA-150+USB2.0
Combo Low Profile PCI
User Manual
English
LINDY No. 70536
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2004)
Resumo do conteúdo contido na página número 2
1. Introduction This Low Profile PCI Host Adapter is a PCI controller board to support Low profile PCI and regular size PCI both in one card. The card can upgrade your desktop computer to have 2 ports Serial ATA to support RAID 0 / RAID 1 features, and five USB2.0 / USB1.1 ports. The board supports a 32-bit 33 MHz PCI bus revision 2.2, USB transfer rate of 1.5Mb/s, 12Mb/s, 480Mb/s and Serial ATA Generation 1 transfer rate of 1.5 Gb/s (150 MB/s). SATA port can access SATA storage m
Resumo do conteúdo contido na página número 3
Provides RAID 1 (Mirroring) to protect the data from a disk failure by writing identical data on 2 drives. Fully compliant with Serial ATA 1.0 specifications. Independent 256-byte FIFOs (32 bit * 64 deep) per Serial ATA channel for host reads and writes. Supports Spread Spectrum in receiver. Features Serial ATA to PCI interrupt masking. Features Watch Dog Timer for fault resiliency. 1.1.3. USB Interface Provides three USB2.0 / USB1.1 ports ( 3 External + 2 Internal). Compl
Resumo do conteúdo contido na página número 4
Disk Mirroring (RAID 1) Disk mirroring creates an identical twin for a selected disk by having the data simultaneously written to two disks. This redundancy provides instantaneous protection from a single disk failure. If a read failure occurs on one drive, the system reads the data from the other drive. 3. RAID BIOS Installation Creating and deleting RAID sets is a function found in the BIOS. During boot up, the RAID setting message will appear and pause for a few moments to allow th
Resumo do conteúdo contido na página número 5
6. Press CTRL+E and then press Y to exit the setup. 7. Continue with conventional Fdisk and Format steps as if you are installing a conventional hard drive. 8.Your RAID configuration is complete. Please proceed to software installation section. 3.3. Deleting RAID Sets 1. As the BIOS boots, Press CTRL+S or F4 to enter the raid bios utility. 2. Select Delete RAID set. Press Enter. 3. Answer Y to remove the RAID set. If the RAID set being deleted is a Striped set, then all of the data wi
Resumo do conteúdo contido na página número 6
Follow the instructions in this section if you are performing a new installation of Windows 2000/XP, and you wish to boot from a device attached to the SATA port. 1. Power off the system. Insert Combo Card into an available PCI slot. Connect serial ATA cable(s) between the SATA port and serial ATA device(s). Power up the system. 2. Put your Windows 2000/XP CD into the CD-ROM/DVD drive, or the 2000 boot diskette #1 in the floppy drive if your system cannot boot from the CD. 3. Press F6 for
Resumo do conteúdo contido na página número 7
installing the driver. 13. The wizard will now copy the required files to the system and start the Driver. After starting the driver the wizard will display a completion dialog, click 'Finish' to exit the wizard. 4.3. Windows XP installation 1. Power off the system. Insert Combo Card into an available PCI slot. Power up the system. 2. During OS boot up, Windows will display the 'Found New Hardware Wizard'. 'Universal Serial Bus (USB) controller'. 3. Select 'Install the software autom
Resumo do conteúdo contido na página número 8
USB Root Hub The driver has started correctly. 4. Double click on 'SCSI and RAID Controllers', if there is no yellow '!' or '?' in front of 'Silicon Image SiI 3112 SATARaid Controller' the driver has started correctly. 5. To view information about the devices attached to the controller, right click the 'Devices' and select Properties from the context menu, then select the tab labeled 'General'. 4.5. Windows 98 SE /ME Fresh OS installation Follow the instructions in this se
Resumo do conteúdo contido na página número 9
standard PCI-to-PCI bridge', click 'Next'. Select 'Search for the best driver for your device [Recommended]' and click 'Next'. 3. Select 'Floppy disk drives' and click 'Next'. 4. When the wizard indicates that it found a driver for the device click 'Next'. Then click 'Finish' to exit the wizard. 5. The Hardware wizard will display that it found 'NEC USB Open Host Controller', click 'Next'. 6. Select 'Search for the best driver for your device (Recommended)' and click 'Next'. 7. Select 'F
Resumo do conteúdo contido na página número 10
SiI 3112 Controller. 4.7. Windows ME installation 1. Power off the system. Insert Combo Card into an available PCI slot. Power up the system. 2. During the system boot up, the Hardware Wizard will display that it found 'PCI standard PCI-to-PCI bridge', select 'Automatic search for a better driver (Recommended)', click 'Next'. Then click 'Finish' to exit the wizard. 3. The Hardware wizard will display that it found 'PCI Universal Serial Bus'. Select 'Automatic search for a better dr
Resumo do conteúdo contido na página número 11
'General'. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. - 11 -
