Resumo do conteúdo contido na página número 1
INDUSTRIAL
1000BASE-T TO 1000BASE-X
MEDIA CONVERTERS
KCD-400 Series
Installation Guide
DOC.060227-KCD-400
-1-
Resumo do conteúdo contido na página número 2
(C) 2005 KTI Networks Inc. All rights reserved. No part of this documen- tation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without per- mission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change. For more information, contact: Unite
Resumo do conteúdo contido na página número 3
The information contained in this document is subject to change without prior notice. Copyright (C) All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. FCC NOTICE This device complies with Class B Part 15 the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received including the interference that may cause. CE NOTICE Marking by the symbol indicate
Resumo do conteúdo contido na página número 4
Table of Contents 1. Introduction ......................................................... 5 1.1 Features ........................................................................................ 6 1.2 Specifications ................................................................................ 7 1.3 Special Functions.........................................................................11 2. Installation ......................................................... 13 2.1 Unpacking ............
Resumo do conteúdo contido na página número 5
1. Introduction The industrial 1000BASE-T to 1000BASE-X media converter series pro- vides industrial strength Ethernet copper-to-fiber media conversion, allow- ing for 1000Base-T-to-1000Base-X over multi-mode or optional single- mode fiber optical media. For industrial environment, the converters are designed with the follow- ing enhanced features exceeding that of commercial media converters: High and wide operating Temperature Wide operating voltage range for DC power input Power input i
Resumo do conteúdo contido na página número 6
1.1 Features Gigabit copper to fiber conversion: 1000Base-T-to-1000Base-SX/LX over multimode or single-mode fiber SFP design : For flexibility, an SFP (Mini-GBIC) connector is provided for the fiber port to accommodate any type of SFP fiber transceiver when needed. Support full wire speed copper to fiber conversion Auto MDI/MDI-X detection function on the copper port Auto-negotiation support Plug and play : no configuration settings is required Link Fault Pass Through : this funct
Resumo do conteúdo contido na página número 7
1.2 Specifications This figure shows the important components of the converter: -7-
Resumo do conteúdo contido na página número 8
Twisted-Pair Interface (Copper Port) Connector Shielded RJ-45 Signal Compliance IEEE 802.3ab 1000BASE-T std. Pin Assignments Auto MDI/MDI-X detection Data Speed 1000Mbps Duplex Mode Half-duplex or Full-duplex Configuration Auto-negotiation support Cable Types Category 5 or higher UTP Link Distance Up to 100 meters Fiber Optic Interface (Fiber Port) Signal Compliance IEEE 802.3z 1000BASE-SX/LX std. Connector SFP for pluggable fiber transceiver Data Speed 1000Mbps Duplex Mode Full duplex Cable Typ
Resumo do conteúdo contido na página número 9
DC Power Interface Interface Screw-type terminal block 1. Two pairs for power wire cascading 2. One pair for power failure relay output DC Jack (-D6.3mm/+D2.0mm) Operating Input Voltages +7V ~ +30V(+5%) Power consumption 2.25W @+7.5VDC input 2.3W @+24VDC input 2.5W @+30VDC input Basic Information Conversion Full wire speed 1000Mbps - 1,488,00pps at 64-byte packets Packet Types Transparent and no modification for - IEEE 802.3 standard packets - IEEE 802.1Q VLAN tagged packets Packet Length No
Resumo do conteúdo contido na página número 10
Certificate FCC Part 15 Class B CE/EMC EMI EN50081-1 Class B EMS EN55024 CE/LVD Safety EN 60950 EN 50081-1/1992 : EN55022:1994/A1:1995/A2:1997 EN61000-3-2:2000 EN61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001 IEC 61000-4-2:1995 ESD Test IEC 61000-4-3:1995 RS Test IEC 61000-4-4:1995 EFT/BURST Test IEC 61000-4-5:1995 Surge Test IEC 61000-4-6:1996 CS Test IEC 61000-4-8:1993 Magnetic Field IEC 61000-4-11:1994 Volatge Int. Dips -10-
Resumo do conteúdo contido na página número 11
1.3 Special Functions Auto MDI/MDI-X Function This function allows the copper port to auto-detect the twisted-pair sig- nals and adapts itself to form a valid MDI to MDI-X connection with the remote connected device automatically. Link Fault Pass Through Function When a link fault is detected on the copper port, the device will force a link down on the fiber port immediately. Similarly, a link fault detected on the fiber port will also force a link down on the copper port. As illustrated in the
Resumo do conteúdo contido na página número 12
Far End Fault Function The fiber port is facilitated with this function. When the fiber port detects a link failure on its receiving circuitry, it will send out an FEFI (Far End Fault Indication) signal to the remote connected device to indicate a remote fault is detected. It also is capable to receive FEFI signal sent from the remote link partner if the link partner detected a receiving fault. Upon receiving an FEFI signal, it indicates a link failure occurred on the transmitting path. This fun
Resumo do conteúdo contido na página número 13
2. Installation 2.1 Unpacking Check that the following components have been included: Information CD The Media Converter unit DIN-rail mounting bracket If any item is found missing or damaged, please contact your local reseller for replacement. The following are available optional accessories: Panel Mounting Bracket The bracket is used for mounting the converter on a panel surface. Commercial-rated AC power adapters: - Rated AC120V/60Hz DC7.5V 1A - Rated AC230V/50Hz DC7.5V 1A - Rated A
Resumo do conteúdo contido na página número 14
2.2 Safety Cautions To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions. Do not service any product except as explained in your system documentation. Opening or removing covers may expose you to electrical shock. Only a trained service technician should service components inside these compartments. If any of the following conditions occur, unplug the product from the electrical outlet and replace the part or contact y
Resumo do conteúdo contido na página número 15
2.3 DIN-Rail Mounting In the product package, a DIN-rail bracket is installed on the device for mounting the converter in a industrial DIN-rail enclosure. The steps to mount the device onto a DIN rail are: 1. Install the mounting bracket onto the device unit as shown below: 2. Attach bracket to the lower edge of the DIN rail and push the unit upward a little bit until the bracket can clamp on the upper edge of the DIN rail. 3. Clamp the unit to the DIN rail and make sure it is mounted securely.
Resumo do conteúdo contido na página número 16
The final mechanical dimensions after installing DIN rail mounting bracket are: -16-
Resumo do conteúdo contido na página número 17
2.4 Panel Mounting The device is provided with an optional panel mounting bracket. The bracket support mounting the device on a plane surface securely. The mounting steps are: 1. Install the mounting bracket on the device unit. 2. Screw the bracket on the device unit. 3. Screw the device unit on a panel. 4. Make sure that there are proper heat dissipation from and adequate ventilation around the device. Do not place heavy objects on the device. -17-
Resumo do conteúdo contido na página número 18
The screw locations and final dimension are shown below: -18-
Resumo do conteúdo contido na página número 19
2.5 Applying Power The power specifications of the device are: Operating V oltage +7 ~ +30VDC Power Consumption Max. 2.5W @30VDC The device provides two types of power interfaces, terminal block and DC power jack for receiving DC power input from external power supply. Using Terminal Blocks Either DC1 interface or DC2 interface can be used to receive DC power from an external power system. Or, DC2 also can be used to deliver the power received on DC1 to next device in cascading way. DC1 + Vdc P
Resumo do conteúdo contido na página número 20
2 Power wires: 24 ~ 12AW G (IEC 0.5~2.5mm ) Install the power source wires with the plug properly. Screw the wire with plug securely. Then, plug in DC1 contacts. If cascading the power to next device is needed, install the power wires and plug for another switch. Then, use DC2 contacts. Note: Only up to four device units can be cascaded to receive power from one main power input source. -20-
