Resumo do conteúdo contido na página número 1
User’s Manual
SCREEN POSITION
DOWN STOP UP
RCM-SC
ROOM CONTROL
SCREEN POSITION LIGHTING
ON / OFF
RCM-SCLT
Relay Control Modules
Control Accessories
Extron Electronics, USA Extron Electronics, Europe Extron Electronics, Asia Extron Electronics, Japan
1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road, #04-01 Daisan DMJ Building 6F
Anaheim, CA 92805 3821 AH Amersfoort PM Industrial Building 3-9-1 Kudan Minami
68-631-01
USA The Netherlands Singapore 368363 Chiyoda-ku, Tokyo 102-0074 Japan
Resumo do conteúdo contido na página número 2
Precautions Safety Instructions • English Warning FCC Class A Notice Power sources This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Note: This equipment has been tested and foun
Resumo do conteúdo contido na página número 3
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 About the Relay Control Modules ................................. 1-2 Features ...................................................................................... 1-2 Chapter 2 Installation and Operation ......................... 2-1 Installation Overview .......................................................... 2-2 UL Requirements ......................................................
Resumo do conteúdo contido na página número 4
Table of Contents, cont’d Relay Control Modules Chapter One 1 Introduction About the Relay Control Modules Features ii Relay Control Modules Table of Contents
Resumo do conteúdo contido na página número 5
Introduction About the Relay Control Modules Relay Control Modules The Extron Relay Control Modules (RCMs) are hard-wired remote control keypads designed for use with the Extron MediaLink Controller (MLC). Refer to the MediaLink Controllers User’s Manual for information on installing, operating, and setting up the controller. All setup must be done via RS-232. See chapter two and refer to the MediaLink Control Program or the MediaLink Controllers User’s Manual for details. Each control module
Resumo do conteúdo contido na página número 6
Installation and Operation 9 Connect a MediaLink Switcher (MLS) to the MLC 206 and Installation Overview to the projector, if applicable. Installation and service must be performed by CAUTION authorized personnel only. These products should 10 Restore power to the MLC, and connect the optional MLS be used with UL approved electrical boxes. See switcher to a power supply. “UL Requirements”, page 2-3. 11 Set up the MLC. To install and set up Relay Control Modules, follow these steps: The setup/c
Resumo do conteúdo contido na página número 7
Installation and Operation, cont’d Rear Panel Connectors and Switches Cabling For each control module to be connected to an MLC, set the rear 1 1 panel DIP switches, then follow these steps: 1. If it hasn’t already been done when the wall box was AD BC EAD BC E installed, cut a length of Extron Comm-Link cable to go between the MLC and the control module. 2. Using the following diagram as a guide, attach a 3.5 mm, 5-pole captive screw connector to the end of the cable that will be plugged into t
Resumo do conteúdo contido na página número 8
Installation and Operation, cont’d 5. Plug one end of the cable into the control module’s remaining communications connector, and plug the other AD BC E AD BC E end into a communications connector on the next control module. The photo below shows control modules (RCM, IRCMs, and/or ACMs) connected to an MLC in a typical daisy chain setup. To 1–2 additional Control Modules (IRCMs, ACMs, RCMs) Control Module #2 MLM faceplate rear view MLC 206 rear view Control Module To an A MLS switcher B C Co
Resumo do conteúdo contido na página número 9
Installation and Operation, cont’d MLC relay wiring for an RCM-SC For Stewart Filmscreen screen controllers, a momentary closure between the up and common terminals, the down Low Voltage and common terminals, or the stop and common terminals Controller will cause the screen to go up, go down, or stop. Stop SCREEN POSITION DISPLAY Low Voltage Controller MLC Relay Ports POWER DOWN STOP UP VCR DVD Laptop VOLUME UNSWITCHED MAX/ MIN RCM-SC 1A 100-240V - 5AMAX Up Extron MLC 206 Up MediaLink Controller
Resumo do conteúdo contido na página número 10
Installation and Operation, cont’d The diagrams included here are examples only. Your The following two illustrations give examples of how to equipment may have different wiring requirements. connect a relay controller to the MLC to turn lights or Refer to the specific wiring instructions provided by the another device on and off. Refer to the manual that came manufacturer of the screen controller and AC power with the controller for specific wiring information for controller that you are usin
Resumo do conteúdo contido na página número 11
Installation and Operation, cont’d Front Panel Features and Operation 120 VAC 50/60 Hz MAX LOAD 15 A SCREEN POSITION ROOM CONTROL DOWN STOP UP SCREEN POSITION LIGHTING C ON / OFF LISTED 7Z37 PROFESSIONAL RCM-SC RCM-SCLT AUDIO EQUIPMENT 1 2 1 1 3 Front Front 1 Screen Position Up ( )/Down ( ) buttons — These buttons can be set up (via the control software) to toggle the screen to move up or down. MINIPORT-15 POWER RELAY Screen Position Stop button — Press this button to stop the POWER 2 CLASS2 WIR
Resumo do conteúdo contido na página número 12
Installation and Operation, cont’d Testing/Troubleshooting Before installing the control modules into the wall or furniture, test the system to make sure that the connections are correct and the modules are working correctly. 1. Connect the cables between the MLC and the control module(s), connect IR Emitters or an IR Broadcaster to the MLC (if IRCM modules are used), and connect a host computer to the MLC’s Config port. If available, cable the A/V source device(s) to the display device (projec
Resumo do conteúdo contido na página número 13
Installation and Operation, cont’d All IR control signals are sent to all devices (video Relay Control Modules sources, projector, etc.) at the same time even if two or three IR Emitters or an IR Broadcaster are installed. The IR sending devices share the same IR Display/Control port on the MLC. For RCM modules, ensure that the wiring from the MLC to the screen motor’s low voltage controller is correct. Refer to the screen manufacturer’s user’s guides. For the RCM-SCLT, ensure that the wiri
Resumo do conteúdo contido na página número 14
Specifications, Part #s, Accessories, Dimensions Specifications Included Parts These items are included in each order for a control module: General Power ............................................. 12VDC from the MLC 206 Included parts Part number Temperature/humidity .............. Storage -40° to +158°F (-40° to +70°C) / RCM-SC (grey, black, white) 70-183-01, -02, -03 10% to 90%, non-condensing Operating +32° to +122°F (0° to +50°C) / or RCM-SCLT (grey, black, white) 70-184-01, -02, -03 10%
Resumo do conteúdo contido na página número 15
Specifications, Part Numbers, Accessories, cont’d Dimensions The following diagrams have been reduced to fit on the page. All dimensions are given in inches. The symbol “ø“ indicates a diameter. RCM dimensions .363 .182 .320 .160 DETAIL A +.000/ Ø.160 max. extrusion around -.010 stud on far side, +.003/ +.003/ Ø.112 thru (4 places). -.000 Ø.166-.000 thru (2 places). PEM insert FHS-440-6 or equiv. PEM insert BSOS-440-16 or Insert from near side. (4 req'd) equiv. Insert from near side. +.
