Resumo do conteúdo contido na página número 1
User’s Manual
HSA 822
®
Hideaway Surface Access Enclosure
68-617-02 Rev. G
08 08
© 2008 Extron Electronics. All rights reserved.
Resumo do conteúdo contido na página número 2
Precautions Safety Instructions • English Warning Extron’s Warranty Power sources � This equipment should be operated only from the power source This symbol is intended to alert the user of important indicated on the product. This equipment is intended to be used with a main operating and maintenance (servicing) instructions power system with a grounded (neutral) conductor. The third (grounding) pin is in the literature provided with the equipment. Extron Electronics warrants this product agains
Resumo do conteúdo contido na página número 3
Resumo do conteúdo contido na página número 4
Table of Contents Chapter 1 • Introduction .......................................................... 1-1 ® About the HSA 822 Hideaway Enclosure................. 1-2 Features ...................................................................................... 1-4 Chapter 2 � Installation ............................................................. 2-1 Installation Overview .......................................................... 2-2 Preparing the Routing Template ...........................
Resumo do conteúdo contido na página número 5
Table of Contents, cont’d ® HSA 822 Hideaway Enclosure Chapter One 1 Introduction ® About the HSA 822 Hideaway Enclosures Features All trademarks mentioned in this manual are the properties of their respective owners. 68-617-02 Rev. G 08 08 ® ii HSA 822 Hideaway Enclosure � Table of Contents
Resumo do conteúdo contido na página número 6
AUDIO IN SE PL U E TCT COMPUTER INPUTS SOG V-SYNC WIDTH AUDIO ANALOG C AO B N T CR O D L E VIDEO OUTP SU E DR T DR SP NC EG O M SP Y N SC YNC LEVEL PEAKING RGB 580xi AUDI O SIE N PL E UT CT C OM P UT E R Introduction ® The installed enclosure fits nearly flush within a table or About the HSA 822 Hideaway Enclosure podium top, storing the AAPs and connectors out of the way The Extron HSA 822 is a furniture-mounted, architectural and out of sight. To access the AAPs and connectors, the user sol
Resumo do conteúdo contido na página número 7
Introduction, cont’d The HSA 822 is available in a variety of surface finishes, ® HSA 822 Hideaway Enclosure including black anodized aluminum, brushed aluminum, brushed brass, and polished aluminum. Features • UL/CUL listing � CSA certification � Easy access to connectors and controls � Durable mechanical movement and latching mechanism � A variety of surface finishes available � A variety of colors of included RJ-45 connector bezels included: black, red, blue, orange, gray, white, ivory, yell
Resumo do conteúdo contido na página número 8
Width of Mounting Surface Installation Installation Overview Preparing the Routing Template Install and set up the HSA 822 as follows: Extron provides a metal routing template for the HSA 822 at no charge. The HSA 822 template is part #70-191-01. Extron 1 If desired, install the optional RJ-45 to RJ-11 conversion recommends using this template as a guide to cut the hole in the kit(s) to replace one or more RJ-45 connectors with RJ-11 table where the HSA will be installed. connectors. Refer to
Resumo do conteúdo contido na página número 9
Installation, cont’d Preparing the Table and Mounting the Enclosure The preferred and recommended method for preparing the table is to use the appropriate Extron metal routing template and a router. Alternatively, you can use a paper cut-out template (see appendix A, “Reference Information”) and a sabre saw or keyhole saw, but this method is not recommended. Prepare the table as follows: The opening in the table for the HSA 822 should be CAUTION cut only by licensed and bonded craftspeople. Exer
Resumo do conteúdo contido na página número 10
AUDIO IS NE PL U E TCT COMPUTER Installation, cont’d 6. Remove the plastic strips that protect the flanged edges of the top of the surface enclosure. If a sticky residue remains, remove it with an appropriate metal cleaning product. Do not use isopropyl alcohol or other solvents to CAUTION clean the HSA. Strong solvents will ruin some finishes. HSA 822 7. Carefully lower the HSA enclosure into the hole to test the fit. If necessary, remove the enclosure and use a file or rasp to enlarge or sm
Resumo do conteúdo contido na página número 11
HSA 822 HSA 822 AUDIO INPUT COMPUTER SELECT Installation, cont’d Cabling and Installing the AAPs Remove two The space behind the AAP panel is limited. The online screws ea. side. Connectivity Configurator, available at www.extron.com, offers guidance as to the fit of AAPs into this space. Extron’s various single space and double space AAP devices, including the various RGB 580xi AAPs, can be mounted to the HSA 822. See appendix A, “Reference Information”, for RGB 580xi AAP part numbers. The sc
Resumo do conteúdo contido na página número 12
Installation, cont’d an appropriate telecommunications or data network or to an Cabling the Enclosure Extron TP product. Bottom panel features An RJ-11 (telephone) plug can be connected to the RJ-45 jack. 3 When cabling the AAP panels and the bottom panel, the bottom RJ-45 connectors match up with the AAP panel RJ-45 connectors as shown in figure 2-7. For example, match the AAP panel RJ-45 2 connector A1 with the underside RJ-45 connector A1, match A2 with A2, and so forth. 1 4 1 B1 A1 A2 B2 3
Resumo do conteúdo contido na página número 13
Installation, cont’d Routing the AAP Cables Bezels The AAP cables must have freedom of movement to permit The HSA 822 ships with RJ-45/RJ-11 connector bezel plug-ins in opening and closing the surface mount enclosure. At the same a variety of colors and a black, blank bezel. Bezel time, they need to be restrained to prevent their rubbing against To change to a different color RJ-45 connector the edges of the enclosure cable access hole in the underside of bezel or if an RJ-45 connector is not n
Resumo do conteúdo contido na página número 14
Installation, cont’d ® HSA 822 Hideaway Enclosure Chapter Three 3 Maintenance and Modifications Replacing an AAP Replacing the Bezels Removing and Replacing the Enclosure Replacing the Gas Lift Adjusting the Top Surface ® 2-14 HSA 822 Hideaway Enclosure � Installation
Resumo do conteúdo contido na página número 15
HSA 822 AUDIO INPUT COMPUTER SELECT HSA 822 I AUD O INPUT COMPUTER SELECT Maintenance and Modifications The HSA 822 surface mount enclosures can be modified in the 3. Disconnect any cables from the rear of the AAPs that are future to replace an AAP. The most probable corrective being replaced. If a cable is no longer required in your maintenance procedures required are leveling the top surface system, carefully pull the cable through and out the and replacing the gas lift. Most of the mainten
Resumo do conteúdo contido na página número 16
Maintenance and Modifications, cont’d Replacing the Bezels Removing and Replacing the Enclosure The HSA 822 ships with RJ-45 connector bezel plug-ins in a The procedures for replacing the gas lift and adjusting the variety of colors and a black, blank bezel. Replace a bezel as levelling of the top surface require removing the HSA 822 from follows: the table. Remove and replace the surface mount enclosure for maintenance as follows: 1. Remove the top and bottom screws on the right and left side
Resumo do conteúdo contido na página número 17
AUDIO IS NE PL U E T CT COMPUTER Maintenance and Modifications, cont’d The flanged edges of the top of the surface enclosure are sharp when the HSA is removed from the table. Exercise caution when handling to prevent personal HSA 822 injury. Enclosure The flanged edges of the top of the surface enclosure CAUTION are bevelled to an ultra-fine thickness of less than 0.04 (4/100)" (approximately 1 mm). These edges Remove (16) are soft and can be easily nicked or bent. Exercise screws. caution whe
Resumo do conteúdo contido na página número 18
Maintenance and Modifications, cont’d 14. Replace the AAP panels in the surface mount enclosure and secure them in place with the screws removed in step 3. If you lose an AAP panel screw, four spare screws are stored in the underside of the enclosure. 15. Secure the two shroud halves to the enclosure frame with the eight screws per shroud half (four per side) removed in step 9. Orient the shroud halves such that the vertical column of center holes align with the column of screw inserts on the
Resumo do conteúdo contido na página número 19
Maintenance and Modifications, cont’d With the top panel bracket detached from the lifting CAUTION platform, the bracket will be floppy atop the gas lift. Ensure that the bracket does not bang into the top flange. Marring of the soft surface of the flange may result Top Panel 5. Turn the enclosure frame rightside-up. Bracket 6. Remove and retain the 9/32" nut and bolt that secure the gas lift to the top panel clevis. Lift the top panel and clevis off of the gas lift and set it aside on the bra
Resumo do conteúdo contido na página número 20
AUDIO IS NE PL U E T T COMPUTER C Maintenance and Modifications, cont’d Adjusting the Top Surface The top lifting panel of the HSA 822 can be adjusted to raise or lower its level flush with the flange. It can also be adjusted to ensure that the lifting panel is horizontal and not tipped. Adjusting the height of the top surface You may be able to adjust the height of the top lifting panel without removing the HSA 822 from the table. If you can reach the height adjustment lock screw slots (figur
