Resumo do conteúdo contido na página número 1
UB-E02
Technical Reference
Guide
10Base-T/100Base-TX
Ethernet Interface board
English
EPSON
404999001
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
UB-E02 Technical Reference Guide CAUTIONS ❏ This document shall apply only to the product(s) identified herein. ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. ❏ The contents of this document are subject to change without notice. Please contact us for the latest information. ❏ While every precauti
Resumo do conteúdo contido na página número 4
Revision Information Revision Page Altered Items and Contents Rev. A ii Rev. A
Resumo do conteúdo contido na página número 5
UB-E02 Technical Reference Guide About This Guide This guide is intended to provide all information necessary for system planning, design, installation and application of the UB-E02 for designers and developers of POS systems. Contents of the Guide The configuration of the guide is as follows: Chapter 1, “System Preparation” Supported operating system, network protocols, TM printers, and other limitations. Chapter 2, “Installation” Gives information on how to install and use the UB-E02. Cha
Resumo do conteúdo contido na página número 6
EMC and Safety Standards Applied Product Name: UB-E02 Model Name: M155B The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the EPSON power supplies and TM series printers.) Europe: CE marking North America: EMI: FCC/ICES-003 Class A Japan: EMC: VCCI Class A Oceania: EMC: AS/NZS 3548, CISPR22 Class B WARNING The connection of a non-shielded interface cable to this board will invalidate the EMC standards of this device. You are cautioned t
Resumo do conteúdo contido na página número 7
UB-E02 Technical Reference Guide CAUTION: Connecting an outdoor overhead LAN cable directly to your product Connecting an outdoor overhead LAN cable directly to your product may lead to lightning damage. If you need to connect such a cable to your product, the cable must be protected against an electrical surge between the cable and your product. You should avoid connecting your product to a non-surge protected outdoor overhead LAN cable. GEREÄUSCHPEGEL Gemäß der Dritten Verordnung zum Gerät
Resumo do conteúdo contido na página número 8
Safety Precautions This section presents important information to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. CAUTION: Be careful to avoid dropping conductive objects such as paper clips on the circuit ❏ board, as they could short circuit connections and cause damage from excessive current. ❏ This product should only be connected to the devices specified in this guide. Connecting other devices could cause damage,
Resumo do conteúdo contido na página número 9
UB-E02 Technical Reference Guide Introduction ® The UB-E02 is the 10Base-T/100Base-TX Ethernet interface board designed for the EPSON TM printers. The board lets you connect your EPSON printer directly to your network and use it as a kitchen printer. Operating Environments Supported Operating Systems ® ® ® ® ❏ Microsoft Windows 95, Windows 98 Second Edition, Windows 2000 Professional, ® and Windows XP Professional ® ❏ Windows NT 4.0 Supported Protocols ❏ TCP/IP Environments for Setup Utility
Resumo do conteúdo contido na página número 10
Supported TM Printers The following printers can use the UB-E02. (The TM-J8000, TM-T285, and RP-U420 cannot use the UB-E02. For new models, please ask your dealer.) ❏ TM-U200 Series ❏ TM-U210 Series ❏ TM-U230 ❏ TM-U325 ❏ TM-U590 ❏ TM-U675 ❏ TM-T88/T88II/T88III ❏ TM-T90 ❏ TM-H5000/H5000II ❏ TM-H6000/H6000II ❏ TM-J2000/J2100 ❏ TM-J7000/J7100 ❏ TM-J7500/J7600 ❏ TM-L90 viii Rev. A
Resumo do conteúdo contido na página número 11
UB-E02 Technical Reference Guide How to Use this Guide Installation Overview Be sure to read Chapter 1, “System Preparation,” before using the product. Perform the following steps to install and configure the UB-E02. See the indicated chapters for detailed information. 1. Install the UB-E02 in your printer. See Chapter 2. 2. Install the TCP/IP protocol in your operating system, if necessary. See Chapter 5. 3. Set the functions of the UB-E02. See Chapter 5. 4. To set the functions of the UB-E02
Resumo do conteúdo contido na página número 12
Contents Chapter 1 System Preparation Supported Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Supported Network Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Supported TM Printers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Other Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 13
UB-E02 Technical Reference Guide Chapter 5 Specifications Printer Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Line Display Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Overview . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 14
xii Contents Rev. A
Resumo do conteúdo contido na página número 15
UB-E02 Technical Reference Guide Chapter 1 System Preparation 1.1 Supported Operating Systems ❏ Microsoft Windows 95, Windows 98 Second Edition, Windows 2000 Professional, and Windows XP Professional ❏ Windows NT 4.0 1.2 Supported Network Protocols ❏ LPR ❏ Socket printing (port 9100 for OPOS) 1.3 Supported TM Printers The following printers can use the UB-E02. ❏ TM-U200 Series ❏ TM-U210 Series ❏ TM-U220 Series ❏ TM-U230 ❏ TM-U325 ❏ TM-U590 ❏ TM-U675 ❏ TM-T88/T88II/T88III ❏ TM-T90 ❏ TM
Resumo do conteúdo contido na página número 16
The following printers cannot use the UB-E02. ❏ TM-J8000, TM-T285, RP-U420 1.4 Other Limitations Be sure to note the following: ❏ When the UB-E02 is installed, the display module connector (DM-D) of the TM printer cannot be used. CAUTION: Do not connect the Ethernet connector cable to the display module connector (DM-D) or the drawer kick-out connector. 1-2 System Preparation Rev. A
Resumo do conteúdo contido na página número 17
UB-E02 Technical Reference Guide Chapter 2 Installation 2.1 Installation Precautions WARNING ❏ Before installing, disconnect the Power Unit from the TM Printer (as well as turning the power switch off). Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the Power Unit is connected can cause damage to the UB-E02 and the printer. ❏ A grounded wrist strap should be worn during installation, to avoid damage from static ele
Resumo do conteúdo contido na página número 18
2.2 Unpacking ❏ UB-E02 ❏ UB-E02 User’s Manual 2.3 Part Names Power supply connector of the printer LED (green) Drawer kick-out 10BASE-T/100BASE-TX LED (yellow) Switch connector of the printer Ethernet interface connector Note: This photograph shows the TM-T88III printer with the UB-E02 installed. 2.4 Functions The switch and LEDs of the UB-E02 provide you with important information on operation and status of the UB-E02. 2.4.1 Switch Type: Non-locking push switch You can do the following
Resumo do conteúdo contido na página número 19
UB-E02 Technical Reference Guide 2.5 UB-E02 Installation CAUTION: Before installing the UB-E02, be sure to set the DIP switches or Memory switches as shown in the table below. For other models, please ask your dealer. Model Setting TM-U200 Series DIP SW 2-8: ON TM-U210 Series DIP SW 2-8: ON TM-U220 Series (STD) *1 DIP SW2-8: ON TM-U220 Series (US) *1 DIP SW2-4: ON TM-U230 Series DIP SW 2-4: ON TM-U325 Series DIP SW 2-8: ON TM-U590 Series DIP SW 2-8: ON TM-U675 Series DIP SW 2-8: ON TM-T88/T8
Resumo do conteúdo contido na página número 20
remove screw remove screw 3. Tighten the screws. If you have removed an interface circuit board that was already installed, fix the UB-E02 using the removed screws. 4. Plug the twist pair cable into the 10BASE-T/100BASE-TX Ethernet connector of the UB-E02 until it clicks. CAUTION: Be sure not to connect a telephone line, display module connector, or drawer kick-out connector cable to the 10BASE-T/100BASE-TX Ethernet connector of the UB-E02. The display module connector on the TM printer canno
