Manual do usuário Yamaha DSP1D-EX

Resumo do conteúdo contido na página número 1

-EX
Owner’s Manual
V480360 R0 1 IP 16
E
200 AP Printed in Japan

Resumo do conteúdo contido na página número 2

FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instruc

Resumo do conteúdo contido na página número 3

n Precautions • Do not allow water to enter this unit or allow the unit • The digital circuits of this unit may induce a slight to become wet. Fire or electrical shock may result. noise into nearby radios and TVs. If noise occurs, relocate the affected equipment. • Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked • If the message “WARNING LOW BATTERY!” appears on the unit. Failure to do so is a fire and electrical when you turn on

Resumo do conteúdo contido na página número 4

Thank you for choosing the DSP unit “DSP1D/DSP1D-EX”, specifically designed for the Yamaha PM1D digital audio mixing system. The DSP1D/DSP1D-EX is an engine controlled by the CS1D control surface. Be sure to ask an authorized Yamaha service engineer to install the boards and set up the unit. Never perform installation and setup by yourself. The following optional boards can be installed in the DSP1D. • CIB1D : Console interface board • EMB1D : Engine management board • PDB1

Resumo do conteúdo contido na página número 5

A ENGINE ID A/B indicators D POWER ON/OFF switch These indicators indicate whether the DSP1D/ Use this switch to turn the power to the DSP1D/ DSP1D-EX is connected to the engine A or engine B DSP1D-EX on or off. When the power is turned on, channel. the indicators 1 - 3 light up. Indicator A lights up if the DSP1D/DSP1D-EX is con- E MIDI IN/OUT/THRU connectors nected to the engine A channel jacks of the CS1D con- These connectors

Resumo do conteúdo contido na página número 6

K TIME CODE IN connector N OUTPUT 1–6 slot This balanced XLR3-31 connector receives SMPTE Use these slots to connect the INPUT connectors of an time code (LTC) for analog input from the external analog output unit AO8 series or DIO8 digital I/O device. The rated input level is –10 dB, and the pin unit to output multi-channel digital audio signals assignment is as follows. from the DSP1D/DSP1D-EX. Use a genuine Yamaha 1=ground, 2

Resumo do conteúdo contido na página número 7

Slots (for IDB1D board) Unit Input channel * DPS1D INPUT 1-48 & ST IN 1-4 DPS1D-EX INPUT 1-96 & ST IN 1-8 (DSP1D + IDB1D for expansion) *The DSP1D has an empty slot available for the IDB1D board. n Dimensions 480 ENGINE ID A B CONTROL I/O 1 2 INPUT CONFIGURATION 48CH 96CH POWER ON/ OFF unit: mm • Specifications and appearance are subject to change without notice for improvement. • For European Model Purchaser/User information specified in EN55103-1 and EN55103-2. Inrush Current: 3

Resumo do conteúdo contido na página número 8

YAMAHA CORPORATION Pro Audio Division, #18/3 P.O. Box 3, Hamamatsu, 430-8651, Japan