Resumo do conteúdo contido na página número 1
Featuring
Resumo do conteúdo contido na página número 2
INTRODUCTION Thank you for purchasing a Monitor 2 mixer, brought to you with pride by the SPIRIT team of Andy, Colin, Chris, James, Simon, Mukesh, Graham, Martin, Paul, Tony and Peter, with the support of many others - we hope you will have as much fun using it as we did building it! SAFETY PRECAUTIONS The SPIRIT MONITOR 2 mixer must only be connected For your own safety and to through the Power Supply supplied. avoid invalidation of the warranty please read this section carefully. The wires
Resumo do conteúdo contido na página número 3
Connecting Up 24 INPUTS Page 3
Resumo do conteúdo contido na página número 4
100Hz HI-PASS FILTER USING MONITOR 2 Pressing this switch activates a steep 18dB per octave filter which reduces the level of bass frequencies only. Use this in live PA situations to clean up Mono Input Channel 1 the mix, reducing stage rumble or popping from microphones. XLR Input INSERT POINT The UltraMic Plus padless input preamp is designed to accept BALANCED or The unbalanced, pre-EQ insert point is a break in the channel signal path, UNBALANCED signals at a wide range of input levels up
Resumo do conteúdo contido na página número 5
MONITOR SENDS 7 These controls route the input channel signal to any one or more Monitor busses and the associated Monitor Outputs, allowing a number of unique monitor mixes to be created. The sends are arranged as a group of mono sends (1-8) and two stereo pairs (9/10 & 11/12). Each group of sends is normally POST-FADE, POST-EQ but may be switched to PRE-FADE, POST-EQ by pressing the corresponding PRE switch. All sends are muted when the MUTE switch (9) is pressed. Sends 9-12 are arranged
Resumo do conteúdo contido na página número 6
FOH Facility OUTPUT SECTION A sub-grouping facility is included on outputs 1-10 to allow the console to be used as a FOH mixer. Pressing the 11-12 switch MONITOR OUTPUTS routes the post-fade, post-insert signal to the Monitor 11/12 These outputs provide summing of the corresponding input channel busses, enabling these outputs to be used as a stereo final mix. monitor sends, and drive XLR-type output sockets from impedance The PAN control positions the monitor signal in the stereo 11 balanced ou
Resumo do conteúdo contido na página número 7
FX RETURNS MASTER SECTION Two balanced Stereo Returns are included for the outputs of effects units WEDGE SOURCE and are made available for mixing directly to the Monitor outputs at a level The Engineers Wedge outputs are normally fed from a mix of the MNTR set by the FX1 RET or FX2 RET controls. If a mono source is used, plugging feeds from outputs 1-12. The pre-fade wedge signal feeds the headphones into the Left jack only automatically feeds the signal to both Left and Right. 2 and meters
Resumo do conteúdo contido na página número 8
l Feed the signal to selected monitor outputs by Setting Up & Troubleshooting Troubleshooting setting the appropriate monitor sends to an initial Hum on outputs when SPLIT OUT sockets are used working level (approx. position 7 on the send No Power Initial Set Up knob). Listen to the signal by feeding the l Check for ground loops, and try isolating the Once you have connected up your system (see the selected monitor signal to the engineers wedge l Is the mains supply present? Check the mains S
Resumo do conteúdo contido na página número 9
APPLICATIONS Live Monitor with Effects BAND INSTRUMENTS/VOCALS Page 9
Resumo do conteúdo contido na página número 10
Live Monitor with In-Ear Monitoring BAND INSTRUMENTS/VOCALS Page 10
Resumo do conteúdo contido na página número 11
Theatre Page 11
Resumo do conteúdo contido na página número 12
FOH Console Page 12
Resumo do conteúdo contido na página número 13
FOH Console with Subgrouping Page 13
Resumo do conteúdo contido na página número 14
System Block Diagram +48V +48V PEAK DETECT INPUT & PFL ON PHASE PFL SENS PEAK 100Hz DETECT SOLO/PFL MIC TRIM INPUT PFL 2 3 PHONES SOLO L 1 PHONES MONITOR EQ SPLIT INSERT SOLO R 2 3 1 MASTER T/B 1 TIP: SEND RING: RETURN MASTER SPLIT OUTPUT WEDGE/SOLO (Internal Link) DIM 2 SOLO L METER L Link - Grounded No Link - Ground Lift SIG MNTR WEDGE 3 SIGNAL SOURCE 11-12 WEDGE DETECT WEDGE L 3 4 DIM 1 2 MUTE 5 WEDGE 6 R 3 DIM 2 1 1-8 7 PRE PFL/SOLO SOLO R 8 ENABLE INPUT WEDGE/SOLO FADER METER R 9 9-10
Resumo do conteúdo contido na página número 15
Connecting Leads ’Y’ Leads (Balanced) Balanced Unbalanced Headphone Splitter ’Y’ Leads (Unbalanced) Insert Leads Lamp Connections Page 15
Resumo do conteúdo contido na página número 16
Control Position Sheet You may freely copy this page to mark control positions to assist in resetting the desk between performances.
Resumo do conteúdo contido na página número 17
INPUTS MONITOR 2 CONSOLE Typical Starting Out Control Positions Page 17
Resumo do conteúdo contido na página número 18
Dimensions 87.5 mm Specifications (3.44") dim. ’x’ Noise Measured RMS, 22Hz to 22kHz Bandwidth. Inputs at unity gain and terminated 150W Output Noise 24 inputs routed, sends down, master @ unity < -80dBu EIN dim. ’y’ Mic EIN @ max. gain (150Wterminated) -129dBu THD+N Width without end trim Mic sens. -10dBu, Faders @ unity, send at max., (for flight case mounting) +20dBu at all outputs @ 1kHz <0.005% Crosstalk (@1kHz) Typical Channel send range >90dB Console dim ’x’ dim ’y’ Channel fader
Resumo do conteúdo contido na página número 19
A Harman International Company Part No: ZM0192
